Search Documents

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only ' about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By M. R. Yalamanchili

The in-situ FTIR/IRS technique has been used to spectroscopically characterize interfacial water near a hydrophilic surface. Interfacial water was examined spectroscopically over known distances from the surface of a silicon single crystal by appropriate design of the geometry and optics of the internal reflection system. The in-situ FTIR/IRS spectra of interfacial water were examined by consideration of the 0 -H stretching region (3000 -3800 cm-1) associated with the vibrational spectra of water. The broad peak: in this region which describes the interfacial water structure was deconvoluted in order to isolate the overlapping spectral features of the interfacial water. Preliminary spectral results indicate the prevalence of an ice-like water structure (-3200 cm-!) at the silicon surface. Importantly, it appears that the interfacial water structure may extend a considerable distance (several tens of molecular layers) from the surface as established from the spectroscopic depth profile measurements which show that the free OH stretch at 3600 cm-1 becomes very significant at distances from the surface exceeding 400 nm.

Jan 1, 1995

By Jack C. Haptonstall

The Tayoltita Unit of Minas de San Luis, S. A. is situated in an isolated corner of the state of Durango, Mexico. The ore deposits in the region were first worked by Indians, but by 1757 the Spaniards had discovered them, and the first systematic exploitation of the mines commenced. By the early 1900's most of the mines had been acquired by American interests, and the San Luis Mining Company was organized. The modern period of exploitation, uninterrupted for the last 74 years, began. In 1962 the company was fully "Mexicenized" in compliance with the modification of the mining law, and the name was changed to Minas de San Luis, S. A. Tayoltita continues as one of Mexico's most important silver and gold mines. The ore is extracted in en extensive underground operation, mining epithermal fissure veins by selective methods. The ore is milled and treated in an efficient counter-current cyanide plant, where 95 % of the silver and 96 % of the gold is recovered. Current annual bullion output is 55,000 kg (1.7 million troy oz) of silver and 1000 kg (31,000 troy oz) of gold from milling 165,000 try (181,900 stpy). Rough, 33-kg (1000-troy oz) bullion bars are smelted at the mine, shipped by air to Mazatlan, Sinaloa, and are thence sold to the Met- Mex Peñoles smelter in Torreon, Coahuila. Ore reserves, blocked by very conservative methods, are currently at 540,000 tons (595,000 st). Ore reserve grade is 425 g of silver and 6 g of gold per ton (12.4 troy oz Ag and 0.18 troy oz Au per st).

Jan 1, 1976

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By Amy McBrayer, Andrea Brickey

Limited research has been conducted related to the development of mathematical optimization models for production scheduling at large surface coal mines using the area, i.e., strip, mining method. Increased economic and technical challenges have led to a new interest in production schedule optimization models for these type of mining operations like those currently applied to model underground and open pit mines. While area mines share similar characteristics to both open pit and underground metal operations, neither an open pit nor underground production scheduling model adequately depicts an area mine mathematically. We present an integer programming model with blending constraints and discuss the challenges and opportunities related to the implementation for area mines as well as future research in area mine production scheduling.

Jun 25, 2023

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

By J. C. Stankus

How to quantitatively identify the loads on a square/arch set is a complicated issue in designing the square/arch set in an intersection/entry. From an engineering perspective, understanding the nature and support mechanism of standing support such as a square/arch set can not only help design the support structure to maintain the roof stability, but save the steel materials and costs of manufacturing, labor, and delivery. Based on the design practices in recent years and successful applications in slope bottom intersections, the authors are confident that the concept of interaction and confinement effect between the steel square/arch set and surrounding rocks is critical in designing a proper steel structure to support an intersection/entry. This paper will detail the design concept and its applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.

Feb 23, 2014

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic, in an economic and environmentally safe manner, is an important problem facing the mining industry in the united states. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), the selective leaching of the arsenic from the roast calcine with a heated caustic solution, the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, the reduction of the residual antimony (collecting the precious metals), fuming of the metal to form a marketable antimony oxide, and crucible reduction of the residue to obtain a gold and silver dore. Experiments have been performed to evaluate the first stage of this process. Batch experiments were performed using synthetic concentrates of stibnite and arsenopyrite. Variables that were studied included: mixture weight fractions, temperature, gas flow rate, oxygen partial pressure and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residue was subjected to arsenic leach tests and the leach solutions were subjected to arsenic and sulfate precipitation tests.

Jan 1, 1993

By Timothy J. Matthews, Timothy J. Batchler, Daniel J. McElhinney

The National Institute for Occupational Safety and Health’s (NIOSH) Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division was commissioned for operation in 1981. The MRS was originally designed for longwall shield research and was the only hydraulic press in the world with the capability to apply biaxial loads to these large structures. The results of this forty-year research program have contributed to improved performance and increased knowledge of longwall shields, mobile roof supports and hydraulic cylinders in the mining industry. Also, considerable research and development have been conducted to develop standing support technologies for the mining industry. The Support Technology Optimization Program (STOP) was developed to evaluate how these various technologies can impact and improve both ground control conditions and mine safety. Additional MRS research has included the performance of ventilation stopping walls including the development of a new testing protocol to evaluate the transverse loading capabilities under arching load conditions and evaluating the performance characteristics of welded wire screen as used in underground mine roof surface control. The NIOSH Mine Roof Simulator has been a reliable and valuable tool for the past forty years for the evaluation of safety structures used in mining, and this research has contributed significantly to the advancement toward safer mines. This paper will summarize those research results and provide a glimpse of planned future activities.

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023