Search Documents

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By J. Kang

Supercritical fluid extraction (SFE) has became an attractive alternative technology to be a new process to recover metal, of which can be substitute the existing Leaching/Solvent extraction processes. Solvent extraction of metallic ions is a technically important and also well-established process that is used in the chemical and hydrometallurgical industries.1 Solvent extraction techniques use the chelation of metallic ions dissolved in liquid solution with organic ligands. Conventional solvent-extraction technique needs large amount of organic solvents and often creates environmental problems.2 More environment-friendly technology is needed nowadays, and there have been increasing attentions to extract metal ions by SFE. CO2 becomes one of the most notable alternative organic solvents due to its nonflammable, nontoxic, nonpolluting, and relatively inexpensive properties with its moderate critical point (73.8 bar, 31.06 °C). Many works have been reported in metal extraction under the supercritical CO2 (scCO2) solvent.3-5 In this study, to recover cobalt from wastes especially from spent lithium ion battery scrap, we selected two ligands ? Cyanex 272 and DEA (diethylamine) for the metal extraction in scCO2. Cyanex 272 is a commercially available extractant along with its series, Cyanex 301 and Cyanex 302. Smart and coauthors measured the metal extracting abilities of these three extractants, and found that Cyanex 301 and Cyanex 302 extracted metal ions much better than Cyanex 272 in the scCO2 solvent.10 The pH of water contacted with high pressure CO2 (70-200 bar, 25-70 oC) is about 2.8-2.95 based on the calculation and the measurement.6-7 Cyanex 272 is known to be less effective as a metal extractant in this low pH environment compared with other Cyanex series. However, when DEA is added to metal extraction reaction with Cyanex-272, DEA works as a strong base to Cyanex 272 converting Cyanex 272 to a deprotonated form (Figure 1), which results in an easy formation of metal complex and the enhanced extraction rate of metal ion.8 Therefore, the purpose of this paper is the metal extraction from spent lithium ion battery waste using scCO2 with Cyanex 272 and DEA.

Jan 1, 2010

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By C. H. Sheerin

Remotely located in the jungle near mount Puncak Jaya [16,500 ft (5,030 my), Irian Jaya, Indonesia rests Freeport's Indonesian copper mining operation. Shortly after start up of Freeport's copper concentrator in 1972, lower than estimated throughput was experienced within the crushing circuit. Within one year, Freeport had successfully engineered a solution, and was operating a 5,500 dmtpd wet screening circuit. Today, after 19 years of successful wet screening expansion and operation, the concentrator processes 57,000 dmtpd.

Jan 1, 1993

By O. M. Johnson

Barite and bentonite are the two principal components of drilling fluid systems used in the petroleum industry for oil and gas well drilling with rotary-type rigs. Approximately 87 percent of the world's annual production of barite is used in drilling applications. Of the worldwide production of bentonite, an estimated 30 percent is used. The drilling fluid, or drilling mud, to which barite and bentonite are added, performs five distinct functions: Lubrication-The liquid phase of the drilling mud lubricates the drill bit, preventing premature failure of the cutting edges and bearings. it also helps to soften the formation being drilled. Cuttings Removal-A mud system must be able to carry rock cuttings broken loose by the bit up to the surface where they can be removed by mechanical or chemical methods. The fluid's ability to perform this function depends upon maintaining a proper balance between the rate of circulation of the fluid and the colloidal properties required to entrain the cuttings in the mud to prevent their settling to the bottom of the hole. Hole Stability-The pressure exerted by the mud against the wall of the bore hole prevents the collapse of the uncased portions of the hole. Downhole Information-The fluid characteristics of the mud should be such that good cuttings samples, cores and electric logs may be obtained to help evaluate a well's productive zones and potential. Control Oil, Gas and Water Flows-It is essential that a drilling fluid offset any pressure from naturally occurring formation fluids in order to prevent a potentially wasteful and dangerous blowout.

Jan 1, 1980

By E. C. Watkins

The fiber glass industry is an industry that. hopefully is still in its infancy and far from a mature business. Fiber glass, as will be discussed in this paper, deals with continuous strand glass as used in the textile laminate and reinforced plastics industries. More specifically, we are speaking of glass used for printed circuit boards, tapes, paper, cloth, pipes, tanks, boats, recreational equipment, roofing shingles, and automotive applications. Compared to the flat, container and decorative glass industries, we are very young. The early patents on fiber glass applications were issued in the 1930's. The type of glass most commonly used in the world and that discussed in this paper is designated as "E" glass. This is a boro-silicate type glass having specific chemical and electrical resistance and low thermal expansion properties.

Jan 1, 1986

By H. EI-shall

The conventional beneficiation scheme for Florida phosphates involves reverse flotation with an intermediatory acid scrubbing step. A single reagent flotation process, using fatty acids or amine as the collector, would eliminate the scrubbing step along with the other flotation step. This can not only simplify the process flowsheet, but also result in reduced reagent costs. The potential of single reagent flotation of Florida phosphates using fatty acids as the collector was examined in this study.

Jan 1, 1993

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

By A. B. Cecala

Two recent Bureau studies evaluated workers&apos; dust exposures in automated pallet loading processes. The first study involved a Bureau designed dust control system using a push-pull ventilation technique. The unit was shown to reduce workers&apos; dust exposures by 76% during pallet loading at a ground silica operation. A hydraulic lift table was used to automate the bag stacking process; this kept the loading height constant throughout the entire pallet loading cycle. The second study evaluated different commercial automated pallet loading systems. These systems automatically stack the bags onto pallets, shrink wrap the pallets, and deliver the pallets to a fork lift pickup location. Results from a ground silica evaluation site indicated respirable dust samples taken were below the Threshold Limit Value (TLV) as established by the Mine Safety and Health Administration (MSHA).

Jan 1, 1990

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the&apos; same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By Nik Sokol, Eric Sekulski, Leo Weiman-Benitez, Jon Hurt, Shrinidhi Vijayakumar, Phaidra Campbell

The Silicon Valley Clean Water (SVCW) Gravity Pipeline (GP) is the first Progressive Design Build (PDB) tunnel completed in North America. As part of the Regional Environmental Sewer Conveyance Upgrade (RESCU) Program, the tunnel is a key component to replacing and rehabilitating components of the existing conveyance system in San Mateo County, California. The GP consists of a large diameter Fiberglass Reinforced Polymer Mortar (FRPM) pipe installed inside a 4.1 m (13.5 ft) inside diameter, 5.3 km (3.3 mile) long precast concrete segmentally lined tunnel. The tunnel was constructed using a 4.6 m (15.2 ft) diameter Earth Pressure Balance (EPB) Tunnel Boring Machine (TBM) through heterogenous silts, clays and sands. Construction included two separate TBMlaunches from a centrally located access shaft, and a tunnel alignment below but in close proximity to very soft Young Bay Mud. Settlement criteria and mitigation strategies focused on protection of an existing 1.42 m (56 inch) diameter force main and adjoining structures along the alignment. This paper discusses the results of the theoretical settlement analysis versus the actual observed ground movements, while also presenting mitigation measures and adjustments made during tunneling to reduce the risks of adverse settlement.

Jun 13, 2023

By Seung Han Kim, Andrew Yu, Carlos Jaramillo, Chu-Chieh Jay Lin

The Penstock Access Tunnel (PAT) concrete plug is a reinforced concrete plug separating the pressure tunnels from the personnel accessible tunnels and has leaked since the first filling at the Helms Pumped Storage Plant located in Fresno County, California. A grouting program was successfully implemented in 2009 to reduce the leakage from PAT concrete plug from over 1,000 gpm to 25 gpm. Recent observations indicated increasing water leakage through new pathways, leading to a decision to execute a high-pressure grouting and waterproof membrane installation program in 2017. The high-pressure grouting and membrane installation program was successfully executed in the areas adjacent to the PAT concrete plug where most of the inflows originated and the largest hydraulic gradients are suspected to present. It reduced the leakage from over 300 gpm of inflow to less than 20 gpm.

Jun 13, 2021

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel&apos;s Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By Martin G. Casto

Mixer-settler extractors, among the oldest forms of extraction equipment, have been used since the beginning of this century. Over the past years, a very large number of mixer-settler devices have been designed and operated. Both batch and continuous flow mixer-settlers have been used. The continuous flow mixer-settler extractor offers a great number of advantages over other extraction equipment. The main advantage of the continuous flow mixer-settler is that it is a compact device. A large number of stages can be assembled in a relatively small area, and more stages can be added fairly easily. Many improvements have been made in the design of mixer-settlers. These improvements occurred in almost every phase of mixer-settler&apos; operation; interface control, mixer design, intrastage pumping, interstage flow of the two liquid phases, and stage construction. It is believed that Barstow1 used one of the first continuous mixer-settler extractors. This mixer-settler had concurrent flow within each stage and countercurrent flow overall. The flow for both phases took place by gravity. The Barstow device and other early mixer-settlers had no separate interface control for each stage, therefore, "tilting" of the stages was necessary. In 1934 Holley and Mott2 designed a mixer-settler in which the heavy phase was recirculated within each stage by the use of a valve controlled central line instead of by a pump. Gordon and Zeigler3 in 1939 were among the first to use an adjustable valve to control the interface levels in a mixer-settler, making tilting of the extractor unnecessary. In 1952 Coplan et al. 4 used a modification of the Holley-Mott idea to build a highly improved mixer-settler with flat common walls, and with the

Jan 1, 1971

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015