Search Documents

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By P. Crouse, J. Obermeyer

"INTRODUCTION Site location and history The Holden Mine is a former underground copper mine that was developed and operated by the Howe Sound Mining Company (Howe Sound) from 1938 to 1957. The mine is located in north-central Washington State, U.S., near Lake Chelan in the area shown as Holden Village in Figure 1. Although Rio Tinto never owned or operated the mine, they are managing and funding a several hundred million dollar clean-up to prevent future water and soil contamination and to reclaim the former mine site under the United States Environmental Protection Agency (USEPA) Superfund process. The former mine included an onsite mill and a nearby housing complex for the miners. Howe Sound developed the mine as a series of near-horizontal drifts and tunnels, interspersed with stopes and shafts that connect different mine levels underground. The tunnels that were excavated to develop the mine total nearly 100 km in length.During development of the underground workings, Howe Sound removed more than 230,000 cubic meters (m3) of waste rock from the tunnels and deposited this material in two waste rock piles. Ore was processed from the mine in the onsite mill to produce a copper concentrate that was shipped off site for smelting. Roughly 10 million tonnes of tailings were produced as a by-product of the milling operation, most of which were deposited in three large impoundments (Tailings Piles 1, 2 and 3) directly south of and adjacent to Railroad Creek. Howe Sound closed the mine in 1957. In 1961, the property was transferred to Holden Village, Inc. (Holden Village), a not-for-profit corporation that maintains a year-round community and operates an interdenominational religious retreat in the former miners’ town. With the exception of the patented private land, the remainder of the Site is on National Forest lands and is administered by the U.S. Forest Service. The mine is remote. It is only accessible by boat or float plane from Chelan, Washington, up Lake Chelan to Lucerne, nearly 40 km. Vehicle access from Lucerne to the mine is provided through a 17.5-km-long winding gravel road that climbs 640 meters in elevation. The general site features are shown in Figure 2. Physical setting The Holden Mine is located on the eastern slopes of the Cascade Mountain Range at an elevation between 975 and 1,050 m above mean sea level. Holden Mine was developed adjacent to Railroad Creek, which lies in a glacial U-shaped valley carved into the igneous and metamorphic bedrock with steep-sided slopes (Figure 2)."

Jan 1, 2017

By Gary P. Thomason

We have all heard a great deal about how various projects were financed or certain companies were successful in obtaining a bank loan. There are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of sources available to finance minerals operations, but let me assure you that these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to almost all minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. In the following pages I hope to provide some insight into what I define as the loan approval process. Having pre-offered my definition, I intend to delineate the various stages of the process and the planning and information I believe should be contained in each. My ultimate goal is to help you think like a banker and, in so doing, stay on top of the process so that you can successfully obtain the funding necessary for your projects.

Jan 1, 1983

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By A. Metzer

When paraffinic gases (ethane, propane, butane) are used as the gas phase in flotation systems, the initial rate of flotation and recovery are generally increased as compared with air. The mechanism of the effect of paraffinic gases in flotation was studied and it was shown that they co-adsorb with the collector ions on the mineral-aqueous solution interface. The effect of this co-adsorption was interpreted in terms of apparent increase of the effective chain length of the collector by the co-adsorbed gas. Adsorption densities, contact angles and flotation behaviour were studied on the following systems: a) Quartz - dodecyl ammonium chloride - ethane and propane b) Calcite - sodium oleate - propane and butane. The positive effect of the co-adsorbed gases is a maximum at low collector concentrations or where critical conditions for flotation with air prevail.

Jan 1, 1974

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By Brian J. Gorva

The key objective of forming a cartel is to increase profits to members of the cartel by taking the following action: a) control output; and b) control price. However, while attempting to obtain monopoly profits the cartel members have to contend with costs associated with cartelization and such costs include the following: political costs; the cost of coordinating output and price; organizational costs (such as cheating); and administrative costs (such as the cost of attending cartel meetings). The objective of commodity exchanges is to provide an open, free market where buyers and sellers may openly complete transactions and pricing information can be immediately disseminated. These transactions include the following: a) to provide facilities for "hedging", or transferring price risk from buyers and sellers of physical commodities to "speculators" through the medium of buying and selling futures contracts, and b) taking physical delivery of metal on due dates.

Jan 1, 1983

By D. C. McLean

One of the few innovations in hydrometallurgy in recent years has been the utilization of the chemistry of basic iron sulfates called jarosites. These have been used to make iron-zinc separations in the processing of zinc concentrates and are a very important factor in both the Duval and Cymet copper chloride processes as a means of preventing iron build-up in the closed leaching circuits. Copper oxychlorides are kindred compounds in that they are insoluble basic salts that form at low pH (1.5 to 3) and precipitate selectively from many base metal solutions. They have been reported in the chemical literature as far back as 1860, and a few of them are known in their mineralogical forms (particularly atacamite) usually as nuisance minerals because of their chloride content. Several patents describe their synthesis and use as fungicides and insecticides, and papers have discussed their formation as corrosion pro¬ducts on copper and brass piping (14).

Jan 1, 1979

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By E. A. Wieselmann

In 1970 Texasgulf (Australia) introduced natural gamma radiation logging of drill holes for exploration in the Hamersley Iron Province of Western Australia. Drill hole logs have allowed positive stratigraphic and structural correlations within complexly folded secondary hematite ore deposits and between individual iron ore deposits separated by distances in excess of seventy-five miles. A Neltronics model KPD logging system and gamma-ray sonde are being used to measure the natural gamma radiation of the enriched Brockman and Marra Mamba banded iron formations. The parent banded iron formations are composed of thick, chemically precipitated iron oxide, chert, iron silicate, and carbonate with thin intro-formational clastic horizons. These clastic horizons give a greater natural gamma radiation than the banded iron horizon, and each clastic horizon has a characteristic radiation profile related to its composition and thickness. Because the natural gamma-radiation profile is unchanged during secondary enrichment of the iron formation, the present stratigraphic position of each drill hole can be established and complex folding can be accurately traced in the sub-surface. Gamma ray logging of percussion drill holes has made feasible a significant reduction in diamond core drilling without loss of accuracy. At the same time, it has provided a means of rapid evaluation of complexly folded iron ore deposits.

Jan 1, 1975

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Ltd. contracted to sink a 1500-m (4920 ft) concrete-lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft has an inside diameter of 6.3 m (20.5 ft) and is equipped with steel furnishings. Dynatec used the owner-supplied, 4.6-m (15.1 ft) diam, double-drum hoist to sink the shaft. For muck removal, 12.5¬t (13.8-st) buckets were used. The capacity of the concrete-¬placement buckets was 4.6 m3 (162.4 ft3). One of the unique features of the shaft sinking operation was the use of a two-¬boom, electric-hydraulic drill jumbo permanently mounted in the shaft sinking stage. An in-the-hole (ITH) drill was used to drill a 200-mm (8-in.) cut hole for the 4.8-m (16 ft), full face rounds. This paper describes the performance obtained with the electric-hydraulic drilling equipment and the high-capacity muck removal and concreting equipment.

Jan 1, 1994

By Edward L. Vickers

When I was originally asked to give this talk, I had certain preconceived ideas of the mining industry's reaction to Operations Research. It seemed at the time to be a rather simple task to collect these ideas for presentation here today. Jotting down these notions, I became concerned that overexposure to this activity called OR perhaps had clouded my outlook on what was actually being done on a nation-wide scale. I felt, to have a better cross section, a questionnaire of current industrial activity was in order. I solicited the response of some 75 mining companies varying in sizes and operating characteristics, and I am pleased to report that the response was good. I received answers from 51. The questionnaire was intended to measure the degree to which their concerns were actually engaged in OR efforts. With all due respect to the people who were so gracious as to answer the questionnaire, I feel that there is a tremendous misconception as to the designed purpose of OR. This is not to imply that there are no active OR groups in the mining industry. But by in large, the majority of the companies sampled appear to be somewhat confused as to what OR really is.

Jan 1, 1962