Search Documents

By Timothy C. Smith, S. Andrew Jacobs, Douglas E. Gonzales, Sandy J. Schexnailder, Carl Urban

At the Schwartzwalder Mine (Cotter Corporation, Golden, Colorado) ion exchange resins have been used in mine water treatment experiments. The experiments, initiated in October 1979 and currently in progress, demonstrate that mine water uranium values can be reduced to levels as low as 10 ppb. Duolite® A-101D, a strongly basic anion exchange resin, was tested in laboratory-scale columns (1 inch diameter) initially and then in pilot-scale columns (4 inch diameter), using both co-current and counter-current operational modes. Observations and conclusions resulting from these studies can be summarized as follows: (1) Duolite® A-101D appears to have successfully extracted uranium at influent levels of approximately 2.0 ppm over multiple loading and elution cycles, consistently producing effluent concentrations as low as 10 ppb uranium. (2) Based upon present test data, counter-current regeneration appears to be the key to successful operation. Upflow loading and downflow elution are the preferred modes for service and regeneration, respectively. (3) Filtration is a necessary pretreatment to remove fine clay and inorganic precipitates that will foul the resin, causing excessive pressure drop and poor loading and elution kinetics. (4) This waste treatment application is unique in that it offers the opportunity to recover some or all of the capital investment in the treatment facility

Jan 1, 1980

By Joseph M. Denk, Gary J. Wirth

This paper summarizes a three phase face ventilation study which was conducted from September 1989 through March 1990 to determine face area methane liberation patterns on two extended longwall sections. The coal seam being mined was considered gassy and the mine liberated an average of 14.4 million cubic feet per day (cfd) or 0.41 million cubic meters per day (cmd) of methane through the mine fans. The mine also used an extensive underground degasification program to recover up to 13.4 million cfd (0.38 million cmd) of methane. Data was collected while the longwall sections were mining from the beginning, middle and end of panel extraction to determine the relationship between the methane liberation and extent of longwall retreat. As expected, methane concentrations did increase from the headgate (intake) to the tailgate (return) side of the longwall face and peak concentrations were detected above the shearer as it passed a methanometer location during mining. There were significant differences in the methane liberations due to the location of the active face within the longwall panel. Results from this study could be used to determine a minimum design face air quantity for an extended longwall section operating under similar conditions.

Jan 1, 1991

By V. Karra, G. Beerkircher

Application of the innovative WaterFlush® crushing technology to the processing of gold, copper, and iron ores is presented for retrofit circuits and productivity gain in each case is stated. New operations containing WaterFlush are described in brief.

Jan 1, 1995

By James G. Donovan, Mario G. Karfakis

A large percentage of Southern Appalachian coal reserves are located in seams less than 36" thick. As thicker and currently more mineable deposits are exhausted, methods of underground thin-seam extraction must be developed. Past experience with highwall mining of thin-seam coal has indicated that recovery rates tend to be lower than in conventional operations. It is suspected that this will also apply to underground thin-seam mining, regardless of proposed technology or mining method. Backfilling is one alternative for thin-seam coal mining; although backfill has been used extensively in hard rock mining its use in coal mining has been limited. The ability of backfill to provide additional ground support may enhance coal recovery by allowing for the design of undersized pillars. Backfill is capable of providing additional ground support by restricting lateral deformation of surrounding coal pillars and roof. This additional support can result in significant increases in recovery from thin-seam coal deposits. However, the overall feasibility of backfill is dependent on the in situ behavior of the fill material, the properties of the fill, the effects of the filling method on the total mining operation, and the cost of filling per extra ton of coal recovered.

Jan 1, 2001

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

By Frank J. Markewicz

The expanding: demand for ilmenite for use in the manufacture of titanium pigments, the knowledge that much of this raw material comes from distant points and therefore has to include a heavy freight charge in the price of the delivered product, and the further knowledge that ilmenite occurs both in the crystalline rocks of northern New Jersey and also in some of the Triassic igneous rocks, were considerations which led to a search for ilmenite-bearing sands in southern New Jersey. That this search was successful is now history, and it is the senior author's privilege to state here that most of the credit belongs to his associates who did all of the heavy work of hand-augering for samples, and who made all of the heavy-mineral separations. We all are grateful to members of the Department of Geology at Rutgers and Princeton Universities for the use of equipment which enabled us to evaluate certain samples from our ilmenite exploration program. In addition, we wish to express our appreciation to many companies for their cooperation and for their permission to publish mineral and chemical analyses. We also acknowledge with much appreciation our debt to the geologists and engineers with whom we have had many lively and rewarding discussions relative to the ilmenite deposits.

Jan 1, 1958

By Norman K. Olson

Hard-rock phosphate was formerly the chief source of all phosphate in Florida. Its mining began as early as 1883 or 1884, reached a peak level in 1907 and ceased in 1966. Production began and ended in the Dunnellon area (Marion County). Nearly all the hard-rock was exported because its P205 value per unit weight is generally more concentrated than that of other phosphate rock. Maximum production, achieved in 1907, was greater than 600,000 tons; the total value for that year was more than $4,000,000. The Florida hard-rock phosphate, considered to be of middle Miocene to early Pliocene age, has an intermittent narrow, linear northwest-southeast trend. The Ocala uplift controls the phosphate distribution for more than 200 miles. Other known, isolated hard-rock areas appear to be related to minor folds on the Ocala uplift. The hard-rock phosphate deposits are a heterogeneous mass of sedimentary fluorapatite, chert and quartz with textures ranging in size from clay to boulder, and in thickness from 0 to 40 feet. Phosphate compounds, principally fertilizers, have been in oversupply since before 1968, but by the middle 1970's some experts forecast a supply-demand balance. A brighter future for exploitation of Florida hard-rock phosphate depends upon one or more of these factors: 1) depletion of present premium grades (74 percent BPL and above) of land-pebble; 2) cheaper electric power from nuclear generators for profitable electric furnace operation; 3) supply and price of sulfur; 4) manageable rail-water transportation costs; 5) development of less costly mining and separation methods; and 6) minimum competition from high-grade foreign phosphate.

Jan 1, 1972

By S. D. Bearden

The world's reserve base is adequate for at least 100 years at the current consumption rate. China, India, and the U.S. are expected to remain the leading producing countries. The U.S. will continue to be the largest consumer of the production. None of the known substitutes for barium sulfate are expected to impact existing applications. World production in 1995 was 4,410Mt. This is about 50% of the projected capacity. Consumption is directly proportional to hydro-carbon well installation activity. Imports are expected to continue to supply more than half of the U.S. requirements.

Jan 1, 1997

By Ronald Allum

Underground copper mining at Magma Copper Company's San Manuel Mine has been un going since 1955. The block caving mine has been producing copper ore at the rate of over 16 million tons per year. Depressed market conditions during the 1980's forced Magma to look at new technology. Late in 1984, Magma began testing new equipment and mining methods at the underground mine at San Manuel, Arizona. The tests resulted in a move towards mechanized production using new procedures and equipment. The goal was to increase efficiency and cut costs through mechanization.

Jan 1, 1988

By J. B. Ackerman, C. S. Bucans

The Sunshine Mining Co. has recently started up its new silver refinery in Kellogg, ID. The new plant recovers silver anc copper values from a high grade tetrahedrite concentrate using hydro- metallurgical processes. The plant and process are both new and have gone through the initial startup phase during the first six months of 1985. The full scale plant was developed from laboratory test work. While the metallurgy of the process worked as expected, the material handling problems were difficult to over-come. As might be expected, those parts of the plant that represented available technology started up easily, while the parts that represented new technology presented the most difficulty. Topics covered in this paper include: 1) insufficient type and amount of agitation in the leach vessels, 2) discharge of a non- homogeneous slurry from the leach vessels, and 3) problems associated with very low flow rates in slurry lines.

Jan 1, 1987

By Svante Lundbrink

A new generation hydraulic rock drill featuring more than 50 percent higher performance than other drills has been introduced by Atlas Copco. In conjunction with the new rock drill, control systems have developed and refined to handle the higher drilling output, and to maintain an acceptable service life of drill string components. These improved features are built into the Rocket Boomer, a new high-performance drill rig, used at the recently completed Hanging Lake project in Colorado. Experiences from this project will be reported together with results from a highway tunnel construction project in Italy.

Jan 1, 1991

By Ricky Chipka, Roshan Thapa, Richard Yovichin, Greg Rogoff, Patrick Niemuth

A 4.5-mile-long, 96-inch-diameter outfall pipeline was constructed between North Texas Municipal Water District’s proposed Sister Grove Regional Water Resource Recovery Facility and the Stiff Creek Discharge Structure. Two TBM-mined tunnel segments were excavated for the outfall pipeline through rock and mixed-face conditions within the Austin Chalk Formation. The TBM mining performance was tracked in detail and evaluated during mining. This paper discusses the TBM configuration, TBM utilization, advance rates, and challenges of both tunnel segments.

Jun 13, 2023

By Tom Plouf, Deepak Malhotra

INTRODUCTION The U. S. mining industry experienced a severe recession in the early 1980's. This resulted in the realization that the domestic mining industry had to compete on a global basis and only the strong or the low-cost producers would survive. The economic viability of a mining company not only depended on maximizing mineral recovery but also on its ability to do so at minimum cost. Companies had to become more productive not only by cutting costs, but also by developing and/or evaluating new technologies in existing or new plants. Several innovative concepts, including in-pit crushing and conveying, fine crushing, improved classification equipment, flotation, column flotation, pressure filtration, etc., have been developed in recent years. This paper addresses the impact of new flotation concepts and equipment on mill design. MILL DESIGN PHILOSOPHY Modern mill design, especially for large capacity plants, has its foundation in minimizing capital and operating costs. Capital costs can be minimized by minimizing the various components of the capital cost: infrastructure, equipment, instrumentation, structural, initial spare parts costs, etc. All these costs are minimized by simplifying the mill design and/or process flowsheet. The simplified process flowsheet, where applicable, consists of a single stage primary crusher followed by a semiautogeneous - ball mill grinding circuit to produce feed for a flotation circuit. Multiple flotation circuits have been eliminated in most cases. These concepts minimize the cost and encourage the use of large capacity equipment while maintaining optimum metallurgical recovery. The philosophy of mill modernization/modification is generally driven by the desire to increase the mill capacity within the limits of the existing mill building. This need is facilitated by using large size flotation equipment and eliminating multiple parallel flotation circuits in order to minimize capital and operating costs. Conventional flotation machine development has paralleled this mill design philosophy. FLOTATION CELL DESIGN Since froth flotation has been the most widely used separation process for over half a century, one would expect that it would be possible to design and select flotation machines for specific applications based on scientific principles. But this has not been the case. Best judgment, experience and personal prejudice have played a key role in equipment selection. These factors, along with the difficulty of evaluating new concepts in commercial plants, has slowed progress in implementation and commercialization of innovative ideas and/or equipment. Conventional Flotation There have been no major technological advances in conventional flotation cell design in recent years. A recent flotation cell survey indicates that 'larger flotation cells are still the order of the day.”(1) A comprehensive review of design of flotation machines indicate that they have been mechanically redesigned and are generally simpler and easier to maintain and less expensive to manufacture. (2,3) The approximate chronological development of conventional cells from the 25 cubic foot cells to the 3000 cubic foot cells, which were recently installed at the Copperton concentrator of Utah Copper, is given in Table 1. Larger flotation cells are the obvious choice for new plants or plants looking for expansion because of the following reasons: • They have lower capital cost per unit volume • Installation costs are generally lower because fewer units require less space • Maintenance costs are lower because of fewer mechanisms • Power requirements (HP/ton dry feed) are generally lower • with increased flotation cell size as illustrated in Table 2 [Table 1. Conventional Flotation Cell Size Development Year Individual Cubic Cell Size, Feet 1925 25 1935 50 1960 100 1965 300 1970 500 1975 1,000 1980 1,500 1985 3,000]

Jan 1, 1989

By J. Leonard Frame

A coal-fired fluidized bed combustion (FBC) system will be installed at the Owatonna Tool Company, Owatonna, Minnesota. Two FBC combustors will burn solid fuels: coal, petroleum coke, and wood and paper wastes. Crushed dolomitic limestone will be used to control sulfur emissions to EPA limits. The combustors will supply indirectly heated hot air and hot water for paint drying operations, washing processes, and space heating. The program is sponsored by the United States Department of Energy and the Owatonna Tool Company, and is one of five programs designed to demonstrate industrial applications of coal-fired fluidized bed equipment. The paper will describe the combustion system and the results of development tests with dolomitic limestone for sulfur emission control.

Jan 1, 1978

By Y. Pan, P. Tukkaraja, R. BHARGAVA, V.V.S. VYTLA, S.J. SRIDHARAN

Panel caving is an underground bulk mining method that uses gravitational force to mine massive, steeply dipping and deep-seated ore deposits at lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. As caving is a dynamic process, designing an effective ventilation system is challenging; therefore, estimating the airflow resistance offered by the broken rock inside the cave is critical. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using the computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

Nov 1, 2022

By Robert Dunne, John Angove

The physical properties of an ore body require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects. This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibil­ity, and to a lesser extent repeatability. The properties looked at were Impact Crushing Work Index, Abrasion Index, Bond Rod Mill Work Index and Bond Ball Mill Work Index. A number of testing laboratories throughout Australia and the US were utilised in the survey. The results showed up some interesting and important features of the procedures used, all of which have become accepted industry standards, and which had varying effects on the final result. Tests such as the rod and ball mill indices would appear to have reasonably robust procedures which allowed for the determinations of the respective index without the introduction of significant variations, although there were indications that variations could occur. The other tests gave a sufficiently different picture to be able to suggest that an argument could be made for a more intensive investigation to be undertaken, with the possible outcome that a modified test procedure or an alternative test is required.

Jan 1, 1997

By A. C. Nixon, A. D. S. Gillies, Hsin Wei Wu

Ventilation and refrigeration strategies for the 3000/3500 orebodies, Mount Isa Mines, Australia were reviewed. The orebodies lie between 1,200 and 1,800 m below surface and are characterised by steep geothermal gradients, intensively mechanised stoping methods and high ambient air temperatures in summer. Providing acceptable working conditions under these situations is difficult and costly. The ventilation air quantity required in the 3000/3500 orebodies exceeds 550 m3/s when the production rate is greater than 2.5 million tonnes per year. The maximum quantity that can be supplied and exhausted using the existing intake and return ventilation system is estimated at about 630 m3/s. For production rates greater than 3 million tonnes per year, either new intake and return airways will need to be developed or innovative approaches such as controlled partial recirculation used. A description is given of technical and economic investigations conducted at Mount Isa into controlled partial recirculation. During these investigations, a major field trial of a controlled partial recirculation system was undertaken with results indicating that an acceptable working environment can be achieved practically and economically utilising this approach. The cost involved in controlled partial recirculation for supplying the required ventilation quantity when the production of 3000/3500 orebodies exceeds 3 million tonnes per year is examined. A cost comparison between recirculation and other conventional alternatives such as new surface shaft or underground booster fans is included. The results indicate that the option of a new surface shaft will incur a high initial capital cost and moderate annual operating costs. The alternative of underground booster fans will necessitate a moderate capital cost and very high operating costs. Controlled partial recirculation, in this case, offers both the lowest capital and operating costs of the three options evaluated.

Jan 1, 1995

By L. C. E. FEIO, R. RAMSDEN

In many parts of the world deep level mining relies heavily on the use of refrigeration for providing safe thermal underground conditions. The trend in South Africa in recent years has been to locate the refrigeration plants on surface and to use these plants to chill water that is then distributed throughout the mine. The surface cooling installation normally consists of a pre-cooling tower in which water is first chilled before it is sent to one or more refrigeration plants for further cooling. Presently, the majority of these refrigeration plants use CFC refrigerants; however, to conform with the Montreal Protocol, these plants will have to be replaced or converted for use with alternative refrigerants. The optimum design criteria for installations using the new generation of refrigerants will be affected by their characteristics and are likely to be different from those currently in use. In light of these developments the industry is examining a number of alternative systems for future installations including water vapour refrigeration. Factors that affect the decision on the type of refrigeration system to be used in mine installations are reviewed. INTRODUCTION Gold mining has been carried out in South Africa for over 100 years and most of the reserves close to surface have been mined out; this has led to mining taking place at greater depths, approaching 4000 m below surface. One of the consequences of operating at these greater depths is that it is necessary to install refrigeration plants to cool the ventilation air so as to provide safe and healthy working conditions. With the current low precious metal prices there is pressure on mines to cut costs and in recent years there has been considerable effort devoted to the design of more cost effective and efficient refrigeration plants and cooling systems. In the last 10 years there have been many studies into the use of ice for specific applications (Eschenburg et al., 1986; Hemp, 1988 and Ramsden and Lloyd, 1992) and at present there are three ice making plants in operation on South African mines, each of which produces ice in different processes. In addition, detailed design studies have been carried out on the "split ammonia system" (Napier and Patterson, 1992). In this refrigeration system the evaporator is located underground close to where the cooling is needed, whilst the condenser and heat rejection system is on surface. As far as refrigeration plants are concerned the trend has been to move away from standard package units to custom built refrigeration installations. This has given the design engineer greater flexibility in the choice of key components for refrigeration installations. For example both screw and centrifugal compressors are used, the heat exchangers for the evaporators and condensers may be either plate or shell and tube, and in a number of installations evaporative condensers are used. In addition, the following refrigerants are in use, R12, R22 and ammonia. The acceptance of the Montreal Protocol and its amendments by the South African government will restrict the use of CFC refrigerants and it will be necessary to re-evaluate various refrigeration systems, including those that do not use conventional refrigerants, such as air cycle and water vapour systems, for new surface installations. Although new systems and refrigerants are being developed, only the following refrigeration installations will be compared in this paper: - a refrigeration system using R134a which has properties similar to R12 - refrigeration system using R22 or a new alternative refrigerant with very similar properties - an ammonia refrigeration system - a water vapour refrigeration system The benefits of new cooling systems are not discussed in detail, since they are largely mine specific and outside the scope of the present paper. Since the optimum design for an air cycle system (del Castillo, 1988) is dependent on the mine layout, this system is also not included.

Jan 1, 1993

By W. R. Hibbard

Emerging from discussions of U.S. energy policy: from the Project Independence Blueprint; from President Ford's statements to Congress; and from several independent appraisals of the situation; there is a clear objective to achieve an appropriate balance of supply and demand in the near term future (1) by developing more efficient ways of using energy and (2) by extending domestic sources of energy. More specifically, the strategy for achieving this goal has three parts (1) Conservation of energy through greater efficiencies in automobiles, appliances, lighting, heating, and industrial processes. (2) Increased domestic production of oil and gas through new sources such as the outer continental shelf and new efficiencies such as tertiary recovery. (3) Substitution of coal and uranium for oil and gas in utility power plants and industrial heating. The goal of energy research and development is to help achieve these goals and to help minimize the economic, environmental and social impact of our shift from imported energy to domestic sources. The focus of this paper is the implications of the expanded use of coal, and the research and development which may help achieve the above goals in so far as coal is concerned.

Jan 1, 1975

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon dioxide (CO2) mineral carbonation is a carbon capture and storage (CCS) technique that can sequester CO2 permanently in the form of durable carbonate minerals. Extendable permanent storage capacity — onshore and offshore storage reservoirs — and the exothermic nature of the mineralization process make this technique attractive [1]. In the present study, maximum carbonation efficiency for aqueous mineral carbonation was achieved through two steps: optimization of calcium leaching from cement kiln dust followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by hydroxylation using sodium hydroxide (NaOH). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in mineral carbonation and also influences and enhances the carbonation efficiency. To maximize the calcium leaching as well as carbonation efficiency, response surface methodology — with either Box-Behnken design or central composite design — was applied. It is the most well-known statistical, fully randomized and bias-free method for determining optimized conditions using quadratic regression models.