Search Documents

By G. T. Adel, W. Z. Choi

In previous work at Virginia Tech, a population balance-model describing the simultaneous processes of size reduction and mineral liberation has been developed. Experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple-composite- class model has been developed. Emphasis is placed on direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By Peter E. Hart

The search for mineral deposits is a difficult high-risk enterprise whose likelihood of success is influenced by a great many factors. Among the most important of these factors are the knowledge and judgment brought to bear on an exploration problem. If, for example, a panel of expert highly experienced geologists could be convened to examine every prospect, it is at least plausible that fewer deposits would be overlooked in the exploration process. Unfortunately, whether a project is undertaken by a private company or a government agency, it is not usually feasible to convene such a panel. Our purpose in this chapter is to describe an experimental system of computer programs called PROSPECTOR that is intended ultimately to provide expert consultation on problems of mineral exploration and resource evaluation. Ideally, PROSPECTOR would serve as a surrogate for a panel of expert economic geologists. However, because the cost of computation is very low and is projected to drop by a factor of about 100 over the next two decades, systems like PROSPECTOR could be made available to the exploration enterprise at large. When consulting about a prospect, the PROSPECTOR system first gives the field geologist an opportunity to tell the program about the most significant features of the site: the major rock types, minerals, and alteration products. The system then compares these observations with a number of stored models of various types of ore deposits and forms alternative hypotheses about the types of deposits that might be present. The system next engages the geologist in a dialogue in order to obtain additional data that would be useful in resolving the multiple hypotheses. The geologist can interrupt the system at any time to obtain clarifications of questions, volunteer additional data, request the reason a particular question has been asked, or obtain a general summary of the state of the consultation process.

Jan 1, 1979

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By V. F. Hollister

Computer programs developed as part of the PROSPECTOR project at SRI International can indicate where the highest grade hypogene copper occurs in porphyry copper prospects. The programs are useful in selecting drilling targets in untested porphyry deposits. Because of mineralogic, structural and lithologic variations in porphyry-type deposits, three distinct computer programs have been constructed; however, this paper considers only the stockwork type in homogeneous rock (similar to the Lowell and Guilbert model). The programs represent models in the form of inference networks that utilize the mineralogic, alteration, lithologic, structural, geochemical and geophysical data normally collected prior to a drilling decision. One example of an application of the PROSPECTOR program for a stockwork-homogeneous porphyry is given: Island Cooper in British Columbia. Computations based on the surface geologic, geochemical and geophysical data for Island Copper clearly disclose the best hypogene grade of the deposit. Other deposits were tested in the programs as well, and in each case PROSPECTOR programs indicate the region with the highest hypogene grade.

Jan 1, 1983

By S. Frimpong, N. Demirel

Overburden excavation is an integral component of the surface mine production chain. The walking dragline is the most economic production equipment for overburden excavation in strip mining. Draglines are capital intensive, and thus, investments in multiple units severely impact the economic viability of projects. The use of few dragline units results in highly concentrated production focus, which must be efficiently managed to derive the potential economic benefits. Efficient use of draglines requires a thorough knowledge of the powered functions, the 3D rotational and translational motions and machine-formation interactions within the operating environment. Dragline kinematics and dynamics are required to understand and characterize machine performance and efficiency. In order to sustain the high productivity in difficult operating conditions, the dynamics of the dragline must be modeled and analyzed based on comprehensive kinematics. This paper investigates the planar kinematics of the front-end assembly and its interactions with the formation during excavation using the “Vector Loop Analysis” formulation with comprehensive simulation modeling in MATLAB Simulink. The kinematic models are used to examine the translational, rotational and angular displacement, velocity and acceleration components of the dragline front-end assembly along defined bucket trajectories during excavation. The results are the precursors for comprehensive modeling to examine the load deformation, torque requirements and dragline stress loading profiles for improving machine health and longevity.

Jan 1, 2006

Mine managers need useful data to support production and maintenance decisions; for example, to evaluate the performance of replacement components. Today, managers rely solely on past experience, supervisors, opinions, and time studies. Our paper describes the concepts and algorithms we are developing for an automatic, intelligent decision support system (IDSS) that will aid managers by reducing and analyzing large amounts of, monitoring system sensor data and report only key production and maintenance information.. IDSS contains a pattern recognition, subsystem (IDSS/PRS) prototype to report graphical trends in traditional time study elements. We are designing. and prototyping a knowledge representation subsystem, using Knowledge Craft Tools, that will learn and adapt to the dynamic mine environment and reason about the recognized patterns using representations of manager's knowledge, equipment, capabilities, and mine layout and operating procedures. This subsystem will reduce, large quantities of time study type information to key issues that interest different managers.

Jan 1, 1989

By J. F. Rakszawski, Robert P. D'Orazio

The use of cyanide in the processing of gold has been documented for over a century. It is still one of the more effective methods of isolating gold, as witnessed by the fact that in 1987 cyanidation was used in the processing of 91.5% of the gold produced in the United States.

Jan 1, 1990

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By Lijun Xu, Ragula Bhaskar

The transport of dust particles from a turbulent air stream on to the surface of a mine entry is mainly due to the effect of diffusion, sedimentation and inertial impaction. While the literature in aerosol science contains many references on particle deposition, most studies apply to smooth surfaces in small, short tubes. The deposition data from those experiments may not be applicable to deposition in mine airways that have large areas of rough surfaces and extend several thousand meters. This paper describes the mechanisms of mine dust transportation and deposition, specifically, by estimating the turbulent deposition velocity for coal dust in mine airways. Data from in-mine experiments on ambient dust concentration and dust deposition along a straight entry were used. A statistical model for dimensionless turbulent deposition velocity was developed, and compared with the models developed by other researchers. The model shows that the distance from the dust source is an important factor in the turbulent deposition of mine dust.

Jan 1, 1995

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By M. J. Howes, C. A. Nixon

INTRODUCTION A safe heat stress control strategy for an underground mine has three elements: Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. Acceptance of a functional relationship between the environ- mental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The environmental measure that reflects physiological strain is the link between the three elements and, since the turn of the century, the discussion of the merits of various indices has been prolific. One problem in selecting a suitable measure or index is the ease with which it can be physically obtained relative to accurately reflecting the physiological strain. For example, wet bulb temperature is simple to measure and, for a particular mining sys- tem, it may adequately represent physiological strain, however, it would not necessarily provide the same relatively safe measure in a different mining system. The acceptance of a measure which can be universally applied has been confounded by both development and predisposition. That is not to say that there is only one "correct" measure and all others are unsuitable. It is self evident that if the application of a particular index has resulted in adequate control, then that mea- sure is correct for that situation. However, an understanding of the limitations is necessary to ensure that adequate control is maintained as mining conditions change. Almost 100 years after the question of heat stress in mines started to be dealt with in a collective manner, an analysis of the available information is leading towards a general strategy to control this problem. In the paper, the developments in heat stress assessment are briefly examined and followed since the earliest published observations on the effect of heat in mines (Haldane, 1905), efforts to determine a relationship between an environmental measure and human performance are reviewed and summarised and the benefits of control strategies such as acclimatisation and shortened shifts are discussed as they relate to Mount Isa Mines. The results of testing the prototype air cooling power instrument are discussed and a heat stress control strategy outlined. HEAT STRESS AND AIR COOLING POWER The operation of the human engine is analogous to other engines where the conversion of chemical energy from the oxidation of fuel to useful mechanical energy is not 100% efficient. In a diesel engine it is about 33% and in a human engine less than 20% resulting in at least five times as much heat produced by the meta- bolic process as useful work done. Metabolic energy production is related to the rate at which oxygen is consumed and is about 340 W for each litre of oxygen per minute. Using measured oxygen consumption and an average body surface area of 2.0 m2, the approximate metabolic energy production associated with different mining tasks is (Morrison et al. 1968):- • Rest, 50 W/m2 • Light work, 75 to 125 W/m2 (machine, LHD or drill jumbo operators) • Medium work, 125 to 175 W/m2 (airleg drilling, light construction work) • Hard work, 175 to 275 W/m2 (barring down, building bulkheads and timbering) • Very hard work, over 275 W/m2 (shovelling rock) Heat balance is achieved when the rate of producing heat (the metabolic heat production rate) is equal to the rate at which the body can reject heat mainly through radiation, convection and evaporation. Heat exchange between the lungs and the air in- haled and exhaled is normally less than 5% of the total and there- fore usually ignored. Any heat not rejected to the surroundings will cause an increase in body core temperature. Since heat stress is related to the balance between the body and the surrounding thermal environment, the main parameters required to be known when determining acceptable conditions are those associated with the heat production and transfer mechanisms. These can be summarised as follows: Metabolic heat production rates (M - W) Skin surface area (A3) (and effects of clothing) Dry bulb temperature (t[ ]) Radiant temperature (t[ ]) Air velocity (V) Air pressure (P) Air vapour pressure (e [ ]) The rate of heat transfer to or from the environment depends on the equilibrium skin temperature t, and the sweat rate S,. These in turn depend on the response of the body to the imposed heat stress and the effect of thermoregulation (Stewart, 1981). Thermoregulation The body contains temperature sensitive structures which send impulses to the brain at a rate depending on the temperature. Both hot and cold signals can be differentiated and the thermoregulatory response ahivated according to which signal pre- dominates. If "cold" signals are dominant, body heat loss is re-

Jan 1, 1997