Search Documents

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By Marco Sonnenschein

Belt conveyors for tunnelling are industry standard and key to high performance of TBM drives. Conveyors reduce traffic in the tunnel and increase safety in the tunnelling process. This paper will illustrate the state of the art of tunnel belt applications in very long and curvy tunnels like the Coxwell Bypass Tunnel Project in Toronto, Canada.

Jun 23, 2024

By Clay Haynes, Tim Pearia, Robert Robinson, Judy Cochran

A 1.89 km-long, 4.5 m-I.D. tunnel was successfully constructed through saturated hard clay, and highly abrasive dense sand and gravel, with groundwater heads ranging from 10 to 20 m. In order to address these conditions, a Lovat earth pressure balance TBM was used, with soil conditioning by foam, water and various polymers. Support was provided by a single-pass segmented concrete lining. Groundwater inflows of 400to 1,600 lpm at times created challenges for changing cutting tools. Surface settlements were generally less than measurement thresholds, except under very low cover at startup. This project provides a pivotal case study of the successful application of EPBM technology in saturated, abrasive glacial soils and the successful application of soil conditioners.

Jan 1, 2003

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental and technical aspects of openpit mining operations. Factors influencing ore loss and dilution fall into two categories: (1) controllable factors, like mine equipment selectivity and blast design, and (2) uncontrollable factors, such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls preblast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, through a number of case studies, the study investigates the relationship between spatial entropy, cutoff grades, blast movement, dig-limits optimization model running time, and profit. The results show that changes in cutoff grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy

Jun 1, 2024

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By Felicia F. Peng

A laboratory fixed bed reactor was used in a study of generating clean thermal energy from coal fine refuse-limestone agglomerates. The major operation variables, including Ca/S mole ratio, agglomerate size, air flow rate and temperature, which affect the rate of sulfur fixation and combustible material utilization, have been examined. The test results show that 70 percent or more of sulfur fixation and 100% of combustible material utilization can be achieved depending upon sorbent, agglomeration, and combustion conditions. The coal fine refuse limestone pellet combustion process (CLC process) requires a simple flowsheet to convert coal fine refuse as a clean solid fuel, while meeting the strict air quality standards for SO2 emissions into the atmosphere. The CLC process is an attractive method to clean up coal slurry impoundments to protect our environment.

Jan 1, 1984

By B. Das, D. D. Mishra, M. I. Ansari

Experiments conducted with a 75-mm-diem hydroryclone have shown it is possible to obtain an iron ore concentrate containing 60% Fe. 2.65% SiO2, and 4.0% Al2O3 from Barsua iron-ore washing-plant slimes. About 60% of the iron values are recovered from slimes containing approximately 49% Fe, 8.9% A1203 and 11% SiO2. The obtained products can be used in the sinter feed for iron and steel making. The key to achieving process success lies in establishing the correct cut point (d50) of the hydrocyclone through the manipulation of operating and design variables, such as spigot and vortex finder diameter, solids concentration and operating pressure. The cyclone efficiency is represented by the partition curve. The cyclone performance, evaluated mathematically from the reduced efficiency curve, is represented by the equation Y = 100[1 -exp(-axb)], where: •X = did 50, •Y = corrected of efficiency (%) and •a and b are constants.

Jan 1, 1994

By Zhou Aimin, Xie Benxian, Song Chongkai, He Zhexiang, Zhang Changqing

Concrete pump is commonly used to transport paste and high-density backfill over relatively long horizontal distances. However, since the investment in concrete-pump and its operating cost are quite high, the application of paste backfill is limited in China. For seeking an alternative paste backfill technology, squeezed-transport technique and equipment has been developed. The new technology has been adopted at Tonglushan Copper Mine of Daye Nonferrous Metals Corp for overcoming a difficulty of long-distance transportation of high-density cemented tailings fill. It proved to be an alternative paste backfill method with simple backfill system, saving investment and low operating costs.

Jan 1, 2001

By Harry Deitzer

Within the industrial marketplace barium sulfate has an established role as a filler or extender pigment for use in a wide array of applications. The focus of this paper is to outline a number of these applications and in each one characterizes those features of barium sulfate which provide value. Following this is a discussion of the process techniques which have been used to develop value from a selected class of barite ores found in southern Missouri. It is appropriate to define some terms which may help in clarifying some concepts as presented. Use of the term barium sulfate refers broadly to the chemical compound BaSO4 Barite will generally refer to the naturally occurring barium sulfate ores and their properties. Barytes, whether bleached or not, will refer to barite ore made suitable for industrial applications.

Jan 1, 1993

By Charles N. Alpers, Jane M. Hammarstrom, Robert R. II Seal, Nora K. Foley

Geoenvironmental models are compilations of geologic, geochemical, and hydrologic information that describe both the pre- and post-mining environmental signatures of mineral deposits. The environmental behavior of seafloor massive sulfide deposits varies according to deposit type. This study has divided massive sulfide deposits into six categories: (1) Noranda-type, (2) Kuroko-type, (3) Cyprus- type, (4) Bathurst-type, (5) Besshi-type, and (6) sedimentary-exhalative deposits. In addition to Fe and Al, the heavy metals most commonly associated with drainage from these deposits are Cu, Zn, Cd, Pb, and As. Metal ratios of mine drainage and natural background waters tend to reflect the primary character of the ores. Variations in pyrite and pyrrhotite contents are reflected in lower pH values associated with pyrite-rich deposit types.

Jan 1, 2000

By H. E. M. N. Moursy, M. N. Ahmad, C. R. Holland, G. M. Walker, R. D. Chandler

This work describes the effect of process parameters on the acidulation of Moroccan phosphate rock using nitric acid, i.e., the nitro-phosphate process. A series of bench scale experiments were conducted, using a stirred tank reactor (STR) system, to investigate the chemical reactions involved and optimum conditions for the formation of nitro-phosphate fertilizer. The effect of reaction time, temperature, mixing speed, acidulation ratio, and acid concentration were investigated, and were found to have an effect on the dissolution of P2O5 from the phosphate rock, using nitric acid. An increase in nitric acid concentration resulted in an increase in P2O5 dissolution, however, the dissolution was also found to be a function of acidulation ratio. A nitric acid phosphate rock ratio of 4:l ensured 90% dissolution for nitric acid concentration > 30%.

Jan 1, 2002

By M. Sagisaka

The purpose of this study is to obtain carbon dioxide emissions by copper production systems and quantitative merit to use copper scraps in Japan. Electrolytic copper and sulphuric acid originating from the refining gas are produced in the system. In this study, the inventories such as the fuel consumption of the unit processes and the in-house electricity generation were obtained from published papers and public statistical data. The following observations were made based on the Life Cycle Assessment (LCA) method: (1) Carbon dioxide emissions from the production of electrolytic copper and sulphuric acid in the system are about 1.0 kg and 0.4 kg/kg-product respectively. The carbon dioxide emissions attributable to the transportation of copper concentrate correspond to 20% of the total emission. This emission is higher than that of zinc because the metal content in the concentrate is lower than zinc. (2) The carbon dioxide emissions from the system decrease with the recycling of copper scrap to the converting process because the consumption of copper concentrate is reduced. The reduction is estimated to be 0.18 kg-CO2/kg-Cu at the point of 0.1 kg-scrap/kg-blister Cu. This corresponds to 9% reduction for the present system. However, this recycling leads to the decrease of sulphuric acid by 450x103 tonne at the point. The recycling of scrap should be evaluated not only from the reduction of carbon dioxide emissions, but also in terms of sulphuric acid demands as well as advantage of waste management.

Jan 1, 2003

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985

By Gilman Y. Murray

The problems connected with the development of economically acceptable water supplies in arid regions are discussed. The techniques for capture and retention of runoff from infrequent desert storms are described and the major factors involved are emphasized. The exploration and planning for a typical water development in southwest United States is described, including an analysis of capital and operating costs for the proposed system.

Jan 1, 1963

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By D. R. Zeni

Current mine development requires the safe, &apos;expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994

By M. B. Mooiman

Cyanidation of gold and silver ores by conventional mining and milling techniques has been practiced for over a century. During the past decade, heap leaching has emerged as a viable process for treating certain gold and silver ores. (1) The rapid development of heap leaching for gold and silver ores is largely a result of lower capital and operating costs and faster start-up time than that offered by conventional mining and milling. In general, these features make heap leaching an ideal approach for exploiting either small or large low-grade disseminated deposits of gold and silver considered to be uneconomic by conventional methods. The development of heap leaching technology has evolved from the operations initiated in the western United States. The basic components of a typical heap leaching operation are depicted in Figure 1. Run-of-mine or crushed ore (usually 1 to 5 ppm gold) is delivered to specifically prepared impervious pads. Alkaline cyanide solution is applied to the surface of the heap and allowed to percolate through the heap (typically 10-30 ft high). Pregnant leach solution which drains from the heap is collected and stored in tanks of sufficient size or in collection reservoirs. Gold and silver are recovered from the pregnant solution and the barren solution is recirculated back to the heaps after reagent make-up.

Jan 1, 1983

By J. W. Gunnett

Abstract. The Surface Mining Control and Reclamation Act of 1977 (PL-95-87), Section 522, establishes requirements for state regulatory authorities to designate lands unsuitable for all or certain types of surface coal mining. Any party having an interest in an area that may be affected can petition for it to be designated unsuitable for mining. Section 522 could present major obstacles to the mining industry by typing up an area in an endless round of petitions. The program under development for Kentucky is examined and analyzed as an example for determining the hidden impacts of Section 522.

Jan 1, 1980

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982