Search Documents

By Steven J. Van Kauwenbergh, Talaat A. B. Lawendy

Batch laboratory-scale beneficiation tests were conducted on four high-iron phosphate samples. These samples included sedimentary ores (Tilemsi Valley, Mali and Tahoua, Niger), a sample from an igneous phosphate deposit (Matongo, Burundi), and a fine-grained phosphatic iron ore processing residue from Chile. The Matongo phosphate deposit occurs as a thick (up to 80 m) residual blanket of P205-enriched soil over solid parent rock (carbonatite and associated rock types). Although the Matongo deposit is an igneous deposit, ore from the deposit can be subjected to beneficiation treatments commonly used to treat sedimentary rocks. The beneficiation flowsheets designed to process these diverse ore types involve attrition scrubbing, size classification, and flotation. At the best flotation conditions tested, phosphate concentrates assaying 32.0%-39.0% P205 and 1.0%-1.5% Fe2O3, were obtained at 64.2%-82.2% overall P2O5 recoveries from run-of-mine (ROM) ores containing 9.2%-28.6% P205 and 5.9%-16.1% F,20,. A cleaner phosphate concentrate assaying 33.1% P205, 1.8% A1203, and 3.3% Fe2O3 at 53.4% overall P205 recovery was obtained from the phosphatic iron ore residue that originally contained 4.5% P205, 8.0% A1203, and 17.6% Fe2O3.

Jan 1, 1993

By H. Köse, C. Tatar, C. Helvaci, F. Simsir

The Çayirhan coal basin is located 124 km (77 miles) west of Ankara,Turkey. With approximately 520 Mt (570 million st) of lignite reserves, the Neogene Çayirhan basin is one of the important coal districts of the central Anatolia region. The Çoraklar formation consists of crossbedded sandstone, channel fill conglomerates, mudstones, carbonaceous shales and volcanoclastic pebblestones, which are fluvial in origin. The lower and upper lignite seams occur, respectively, in the lower and the uppermost parts of the Çoraklar formation. The lignite deposits are in the Çayirhan and Koyunagili portions of the Beypazari Neogene basin. The Çayirhan coalfield consists of lower and upper lignite seams. The lower lignite seam does not outcrop at the surface. Its lateral discontinuity and relatively low sulfur content, plus sedimentologic and stratigraphic features of the associated sediments, indicate a fluvial origin. Thus, the lateral spreading and geometry of the lower lignite deposits were controlled by the channel, flood plain and well drained marshes of a fluvial system. The mining method employed at Çayirhan is the fullymechanized, retreat, working longwall with caving system. Due to ventilation, haulage and tectonic conditions, panel lengths from 0.6 to 1.7km (0.4 to 1.1 miles) are chosen, and 220-m (720ft) face lengths are used. The annual coal production is 2.2 Mt (2.4 million st).

Jan 1, 1994

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By William C. Cooley

Modern tunnel boring machines are subject to excessive cutter wear and bearing failures when used in hard and abrasive rock. In very hard rock, the high cost of cutter and bearing replacement, combined with slower excavation progress, make it more economical to drive tunnels by conventional drill and blast methods. The use of high pressure water jets to break rock provides a promising alternative. Experimental data indicate that the specific energy (the energy expended per unit volume of rock broken) decreases as the water jet pressure increases. Continuous jets are generally limited to pressures below 100,000 psi, whereas pulsed jets from a water cannon can attain much higher pressures. Therefore, the Federal Railroad Administration of the U. S. Department of Transportation has sponsored the design (Ref. 1 & 2) and the fabrication and testing (Ref. 3 & 4) of a water cannon to determine its effectiveness in rock disintegration at very high pressures. This paper reports the results of laboratory tests with pulsed jets against large rock samples at pressures of 125,000 to 650,000 psi and field tests against dolomitic limestone and granitic gneiss at pressures near 450,000 psi. Although initial tests were made with a small nozzle, operating at off-design conditions (Ref. 4), this paper only covers results with the full-size nozzle, including 55 laboratory test shots and 67 field test shots.

Jan 1, 1974

By G. J. Grott

Direct Production Costs for Solar Sa 1t approximate the trucking cost for 160 Km. Operations near markets appear unusually attractive at first look. However, many desert operations have been plagued by dust storms yielding salt too high in insolubles for most uses. This paper relates the history of a successful operation in a dust storm area. Saturated brine from the solution mining of LPG storage caverns is evaporated in solar ponds yielding 99.95% sodium chloride (dry basis). Purchased energy is one-eighth that of vacuum pan operations. Production scale tests have proved it works at another desert location using a more complex brine. A new approach for refining soluble salts at ambient temperatures is demonstrated by bench scale and pilot work. Again, savings in purchased energy exceed 80%, even when temperatures are raised to reduce refining time.

Jan 1, 1988

Ravensthorpe Nickel Operation (RNO) is a major new mine and processing plant currently being constructed by BHP Billiton in a ?green field? site near the small town of Ravensthorpe, about 150 km west of Esperance and six hours drive from Perth in Western Australia. Ensuring that the project has a positive overall impact on the surrounding region and that this extends well beyond the life of the operation will be a major challenge for RNO, state and local government, and the local community. For the last two years, the Centre for Social Responsibility in Mining (CSRM) has been assisting RNO management and the RNO Community Liaison Committee to develop a community sustainability monitoring framework for the project. This paper reports on the process that was used to develop the framework, describes the main elements and briefly discusses key learnings from the exercise.

Jan 1, 2007

By M. Yekeler

The critical surface tension of wetting values (Ye) of realgar (AsS), talc [Mg3si401o (OH) 2]' stibnite (Sb2S3), and sulfur (S) were determined by flotation in the absence of conventional flotation collectors as 38.7, 38.0, 35.5, and 30.0 dyne/cm, respectively. The surface tensions of flotation media were arranged by methanol. Separation of binary mixtures of these minerals was performed exploiting their Ye differences-which form the basis of the "ganuna flotation process". One step flotation test showed that sulfur floats preferentially from its mixtures with realgar and stibnite at recoveries of 73.6 and 70.7 % and grades of 81.7 and 91.2 %, respectively. The separation of stibnite from realgar gave a recovery of 4.1 % and a grade of 41.2 % for stibnite, indicate that a minimal Ye difference of 3.6±0.2 dyne/cm is essential for such separation when conventional flotation reagents are not used. This paper presents data and describes the approach employed in these separations.

Jan 1, 1994

By C. Huang, S. Lin, Y. J. Wang

Introduction A mine characteristic curve is of great importance for both theoretical analysis and daily management of a mine ventilation network. Ventilation engineers are well acquainted with the ways of obtaining and using a mine characteristic curve that is conventionally associated only with single-fan networks. However, for a multiple-fan network, difficulty has long been recognized in defining the curve, not to mention, obtaining or using it. To extend the concept of mine characteristic curves for a multiple-fan network, a subsystem-based approach has been introduced by Wang (1992a). He defines a subsystem characteristic curve for a multiple-fan network and discusses the numerical procedure for constructing the curve. A graphical method of obtaining a subsystem characteristic curve for serial-parallel, multiple-fan networks has also been accomplished (Wang, 1992b). In spite of the maturity of the fundamental concepts related to and the numerical analysis tool for a multiple-fan ventilation network, information regarding the related laboratory tests is very scarce. To make up this gap, laboratory experiments have been done by using a two-fan experimental network. This paper presents the methodology and major findings regarding the construction and features of a subsystem characteristic curve. Characteristic curves and measurement fundamentals A characteristic curve A characteristic curve is a graphic presentation of the relationship between any two variables of a two-terminal component. It is typically defined in the form of a quantity-pressure curve for a ventilation component, which can be a single branch (airway), a fan, a regulator, a portion of a network or even a whole network. If a component is a single branch, the curve is called a branch characteristic curve. If it is a fan, then the curve is called a fan characteristic curve, and so on. Figure I illustrates the characteristic curves of some typical ventilation components. A general method for obtaining a characteristic curve from measurement is to apply an adjustable-pressure source between the two terminals of a component and measure the quantities corresponding to the different pressures. Mine characteristic curve A single-fan network can be easily divided into two ventilation components, the fan and the remaining network. The latter consists of only branches and regulators. Under this subdivision scheme, two characteristic curves can be constructed. They are the fan characteristic curve and the characteristic curve of the remaining network. The latter is referred to as the mine characteristic curve or the system characteristic curve. Although the general method for constructing a characteristic curve from measurement can be applied to obtain a mine characteristic curve, there is a shortcut for constructing the curve by introducing a mine resistance factor R. It is a constant if all of the resistance factors in the network are constant. R relates mine pressure H with quantity Q as in: H=RQ2 (1) For a given R, Eq. (1) can be directly used to plot a mine characteristic curve by assigning a series of Q values and calculating the corresponding H values. Hence a shortcut to constructing a mine characteristic curve is to measure one set of mine pressure H and quantity Q values, calculate the mine resistance factor R using Eq. (1) and then plot the curve. Subsystem characteristic curve Applying a similar scheme as is used for a single-fan system, divide a multiple-fan network into two components, a fan under consideration and the remaining network that contains all the other elements (branches, regulators and remaining fans) of the network. The fan under consideration

Jan 1, 1994

By Bruce M. Davis

The variogram is the function used to express the intercorrelation of a regionalized variable. It is used to quantify, for example, the natural variability of mineralization and in that sense may be thought of a average disimilarity between metal quantity at two points inside a deposit.2 As David2 explains, appropriate mathematical functions of distance and direction are used to characterize variograms, a process that he says is analogous to selecting a normal or lognormal model for an observed distribution. Methods for choosing a model for the underlying variogram of a random function based on the sample data appear in the literature.3,8 A crossvalidation procedure is available to check the validity of the model.3 However, statistical validation of the choice of the model through the mechanism of hypothesis testing is not presently available. In the section to follow, notation and background material is presented upon which a large sample test procedure will be constructed. The stationarity assumptions presented refer to covariance stationarity. A test procedure is then proposed, and an example is given for the case of the one dimensional random process.

Jan 1, 1979

By Thomas W. Camm

A WINDOWS-based object-oriented expert system for prefeasibility evaluation of hard rock mines is being developed at the Western Field Operations Center (WFOC) of the Bureau of Mines. Designed for use with the Bureau's Cost Estimating System (CES), this expert system assists an evaluator in choosing an underground mining method, and the related design parameters. The system provides the engineering and design guidelines necessary for an evaluator to perform a prefeasibility type cost estimate.

Jan 1, 1992

By Robert F. Conley

In the mining, manufacturing and application of inorganic pigments, dispersion contributes significantly. This is especially true with mineral pigments because of the variety, in slurry operations required for their processing. Such operations include any of the following: (1) mine-transport (2) wet grinding (3) flotation/beneficiation (4) wet magnetic separation (5) selective floculation (6) size classification (7) chemical processing (8) spray drying Dosage levels and general economics of dispersant use are broadly variant, being dependant upon the agents employed, from the simplist, i.e., sodium silicate or sodium carbonate, to the more complex, as polyacrylates and organo-phosphates. In certain unit processes the dispersant must exhibit unusual chemical stability and persistence, e.g., in protracted pigment slurry shipments. In others, the agent should be fugitive to prevent secondary reactions from occurring, e.g., with high temperature calcination where alkali salts can act as aggregation fluxing agents.

Jan 1, 1985

By R. Schuerch, G. Anagnostou, R. Poggiati

"The paper presents dimensionless design diagrams for estimating the stand-up time of a tunnel face in saturated ground of medium-low permeability. The diagrams cover a wide range of ground parameters and apply to shallow tunnels (overburden less than two diameters). As the time-dependency of the face stability in water-bearing ground is associated with the consolidation process in the soil ahead of the tunnel face, the stand-up time is determined by means of hydraulic-mechanical coupled spatial stress analyses. The results presented are important for tunnel engineering practice, e.g. when estimating the feasibility of atmospheric interventions in the working chamber of a closed shield. INTRODUCTION The response of water-bearing medium-low permeability ground to tunnel excavation is time dependent. The time-dependency is due to a transient seepage flow process that is triggered by the excavation and develops slowly over the course of time. Experience shows that the short-term behavior the ground is more favorable than the long-term one: the deformations increase with time; the tunnel face may be stable initially and fail only after some time. The time over which the tunnel face remains stable is called the stand-up time. This paper investigates the time dependency of the tunnel face stability assuming that all time effects are due to consolidation rather than creep. This assumption is reasonable for shallow tunnels crossing water-bearing soils. In the problem under analysis, the unsupported tunnel face remains stable under the undrained conditions prevailing after excavation, but collapses before reaching the drained conditions prevailing at a steady state. The assessment of the stand-up time is important from an economical point of view for both mechanized and conventional tunneling through weak water-bearing ground, as a long stand-up time removes the need for face support or ground improvement works during standstills, thus saving time and money, while short stand-up times require hyperbaric interventions or the implementation of costly and time-consuming auxiliary measures."

Jan 1, 2016

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By J. S. Long

A finite-difference model using a digital computer was constructed to assist in the water management of a proposed oil-shale mining operation in the Piceance Basin in Colorado. The presence of ground water is both a detriment and a benefit for development of the resource. On one hand, dewatering is required because permeable zones are present in and above the oil-shale sequence, and rich oil shale at the proposed mine is as much as 457 m (1500 ft) below the water table. On the other hand, ground water is the most feasible source of water for processing the oil shale. A ground- water model was constructed to simulate the development of an environmentally acceptable water-management system that will satisfy both the mine-dewatering requirements and the water-supply requirements for processing. The ground-water model discussed in this chapter was constructed for the Rio Blanco Oil Shale Co. (RBOSC) by International Engineering Co., Inc., a subsidiary of Morrison-Knudsen Co. The model was applied to evaluate dewatering and water control systems for several open-pit mining plans initially investigated to develop Federal Lease Tract C-a. A collateral application of the model analyses was to project effects of the proposed dewatering operation on the regional ground-water regime in connection with a permit acquisition program by RBOSC. Subsequently, RBOSC has completely changed its mine development plan and has adopted modeling and related techniques more suitable for study of that plan and dewatering operation. The authors of this chapter are solely responsible for the contents and conclusions.

Jan 1, 1979

By R. Schlüter

"The global mining industry is facing increasing challenges in terms of geological, technological and social aspects. Potential exploi-tation of deposits shows a tendency to increasing depth with complex ores and decreasing grades. A promising approach to deal with these constrains is by applying alternative extraction methods like (bio-)hydrometallurgy as in-situ leaching (ISL) technology. The Bergakademie Freiberg University of Mining and Technology established the “Biohydrometallurgical Center for strategic Elements” (BHMZ) to foster the interdisciplinary research along the entire biohy-drometallurgical process chain to extract indium from sulfide ores. The involved Department of Underground Mining Methods deals with the design and implementation of a pilot-scale underground testing facility for microbial in-situ stope leaching in its “Research and Educational Mine”. This paper discusses the potential of in-situ bioleaching under technological aspects. In addition, different conditioning approaches based on hydraulic and explosive methods for enhanced permeability in the formation are introduced and the gathered data will be presened. INTRODUCTION A reliable, substantial and sustainable supply of raw materials is of crucial importance for any industrialized country. This dependency applies to “strategic elements” including rare earth elements (REEs), platinum group metals (PGMs) as well as a variety of other metals like indium and germanium which are needed for high-tech industry and products such as electric and electronic devices, fibre optics and laser technology (Barakos et al., 2016; European Commission, 2010). Due to the economic growth of the BRIC-countries (Brazil, Russia, India, China), the resource policy of China as well as the volatile world mar-ket prices of different metals the availability of these critical raw materi-als and therefore the dependency of the high-tech producing countries has become increasingly important (Barakos et al, 2016). Adequate supply is often affected by the increasing depth of de-posits, lower metal concentrations and more complex ore mineralogy. In addition, mining activities are increasingly restricted by their envi-ronmental and social impact and footprints. As a consequence, con-ventional mining and processing methods are limited by high energy consumption and technical constraints."

Jan 1, 2018

By Prasad Kummarapurugu, Maija Teijonsalo, Sirkka-Liisa Jamsa-Jounela

There has been a significant progress in the use of mathematical modeling and simulation in the minerals industry in the last decade. Process models have moved from academic world to important industrial tools. This paper reviews the status of mineral processing simulators and recent progress in simulator development and applications is discussed. The simulation for process design and optimisation is now an established technique, as evidenced by its increasing use of practising engineers through commercially available simulator software. The paper presents a systematic approach to the process study procedure for the control system development, clarified by practical case examples calculated by SimCon - a novel steady-state simulator for mineral processes. Examples of the application of SimCon in drawing flowsheets, calculating mass balances and making simulations for grinding and flotation processes are presented. At the end of the paper, the state-of-the-art and the future of computer-aided pro- cess study at mineral processing plants is discussed. Keywords: Simulators, modelling, object oriented programming, computer aided control system design

Jan 1, 1996

By H. Wilcox, M. Prichard, Y. P. Chugh

Environmental considerations related to the disposal of coal combustion byproducts (CCBs) and the impacts of deforestation associated with the harvesting of timber for utilization as roof supports in mines should become more severe in the future, as landfill space and suitable timber reserves become more scarce. To help address these concerns, lightweight artificial supports, such as post and crib elements, that use large percentages of coal combustion byproducts as aggregate have been developed for use in underground mines. These structural products show equal or better engineering characteristics than timber, and they have the potential to replace timber support in underground mines. CCB-based ultralight structural material (ULSM) has also been developed and commercialized for use in the construction of ventilation stoppings in underground mines. The bulk densities of these blocks range from 0.40 to 0.64 g/cm3 (25 to 40 lb per cu ft) with more than 75% CCBs. Efforts are also given to develop and demonstrate large volume CCB-based subgrade improvement technique for road construction. Soil treated with SIUC fluidized-bed combustion (FBC) fly ash developed an immediate bearing value exceeding 25% with a swelling strain of less than I %, which is greater than untreated soils, and met Illinois Department of Transportation (IDOT) standard specifications. In this paper, development procedures, engineering characteristics and beneficial uses of CCB-based structural products are given.

Jan 1, 2002

By Brian T. Hamilton, Richard Piliounis, Cian Murphy

"The Eglinton-Crosstown Light Rail Transit line is a 19-kilometre corridor with a 10-kilometre underground portion currently being constructed by Metrolinx in Toronto through a densely populated urban environment. Tunneling works are being completed through two separate design-bid-build contracts that include consideration for a phased handover to a follow on contractor who will take ownership of the tunnels, including warranties, and will complete the stations and remainder of the system through a PPP delivery model including maintenance of the system for 30 years. Warranty provisions, settlement apportionment, tunnel leakage, potential delays and conflicts between contractors are just some of the risks the team managing tunnel contract integration had to consider when developing the PPP contract. This paper will present an overview of how these risks were assessed and allocated through the contracts and the strategies adopted to minimize risks to Metrolinx while ensuring successful procurement was maintained. INTRODUCTION The Big Move is a 25 year, $50 billion ($-CAD) plan for coordinated and integrated transportation in the Greater Toronto and Hamilton Area (GTHA) in Ontario, Canada. This plan has been initiated by Metrolinx, a division of the provincial government of Ontario, and its vision, goals and objectives are rooted in creating a high quality of life; a thriving, sustainable and protected environment; and a strong, prosperous and competitive economy for the GTHA. The Big Move will triple the length of rapid transit service in the GTHA to 1,725km, significantly increase the percentage of the GTHA population living within two kilometers of rapid transit, reduce commute times to an average of 77 minutes per person per day and decrease greenhouse gas emissions from passenger transportation per person by 29%. Work is currently underway on several projects and more than $16 billion ($-CAD) of the planned investment has already been committed. A key project that forms part of this commitment is the Eglinton Crosstown Light Rail Transit (LRT) Project which is being delivered in the City of Toronto under Metrolinx’s Rapid Transit (RT) Program. This complex and sizeable undertaking has been broken into a number of separate contracts comprising: LRT Vehicles contract; Eglinton West Tunnels Project; Eglinton East Tunnels Project; and a Public-Private-Partnership (PPP) contract to complete the underground stations, at-grade stops, all rail infrastructure and systems and to maintain the entire system for 30 years. The PPP contract, which includes an initial capital portion of approx. $5.1 billion ($-CAD), has recently been awarded to Crosslinx Transit Solutions, a Special Purpose Vehicle (SPV) consortium comprised of SNC Lavalin, Aecon, Dragados and EllisDon."

Jan 1, 2016

By P. M. Solozhenkin

The proposed technology of antimony calcine processing includes ferrochloride leaching of calcine, reducing solutions, hydrolysis of hydrochloride solutions with antimony oxochloride isolation, synthesis of antimony trioxide by SbOCl neutralization and its drying, regeneration of hydrolysis solutions. The optimum parameters of separate stage of process has been determined and the chemical character of process has been given. During the leaching of calcine we succeeded to transfer 92.16- 95.66% antimony to solution. On the worked out sheme we attained recovery of antimony to antimony trioxide near 90 .5% Antimony triozide contains 99.5% Sb2O3. The composition of sinter burdens for pigments preparation "Naples Yellow" different colours from brightly-yellow, yellow and lightly yellow has been proposed. Three-sulfuretted antimony-antimonic cinnabar have been prepared by precipitation of antimony solutions by potassium sulfur-bearing solution. The prepared compounds correspond to inorganic pigments for artistic paint. The amorphous antimony-ferrous black we prepared by aluminium cementation of hydrochloric antimony solutions. The ferrous black were used as artistic paints and for coating of metals by antimony.

Jan 1, 1995

By D. Leppert

Large deposits of natural zeolites may provide cost-effective alternatives for treatment of soil and water contaminated ) with heavy metals and radionuclides. Research on the Bikini atoll demonstrated that addition of clinoptilolite to the soil significantly reduces cesium uptake by plants. Re- search on the potential use of zeolites in soils at Bunker Hill, ID indicated only minor benefits at very high contamination levels vs. US Bureau of Mines (USBM) work on the use of zeolites for treatment of mine waste waters emphasized problems with natural waters that previous studies have not addressed. High levels of competing calcium in natural waters significantly decrease the effectiveness of zeolites for heavy metal sorption and may limit the usefulness in these applications.

Jan 1, 1991