Search Documents

By R. E. Johnson, J. E. Dutrizac, B. R. Palmer

Silver sulphide (acanthite) and lead sulphide (galena) dissolve relatively rapidly in FeCl3 media with the formation of elemental sulphur and soluble silver and lead chlorides. Parabolic kinetics are observed, and the leaching rates are controlled by the outward diffusion of the AgCl and PbCl2 reaction products through the constantly thickening elemental sulphur layer formed on the sulphide. Hence, both leaching rates are strongly dependent on those variables which affect the solubility of AgCl or PbCl2 at the reaction interface. The rates therefore increase with increasing temperature and total chloride ion concentration, but decrease in the presence of elevated concentrations of AgCl or PbCl2. By contrast, neither sulphide is significantly attacked by ferric sulphate media, even at high Eh values. Although the reasons for the refractory behaviour of Ag2S in sulphate media remain unknown, the low rate of PbS attack is attributable to the passivating layer of PbSO4 and elemental sulphur formed on the surface of the galena.

Jan 1, 1993

By Alain A. Sonntag

This paper presents the most recent developments in KREBS technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1989

By Xuebin Liu, Yi Shang, Can Zhou, Hongqiu Zhu, Junbo Du

In the neutral leaching process of zinc hydrometallurgy, the pH value directly affects the leaching rate of zinc calcine. However, due to the complex mechanism of the leaching process and frequent fluctuation of working conditions, it is difficult to control the pH value by manual control. Therefore, this study proposes a fuzzy control method based on rule extraction under multiple working conditions, and analyzes the pH control performance. Firstly, the different operating states are classified according to process mechanisms and the Pearson method. Secondly, under the framework of the active learning algorithm, the approximate linear dependence (ALD) method is introduced to iteratively select samples with rule information in the original sample set for manual annotation. Then, the support vector machine (SVM) method is used to extract fuzzy control rules in different working conditions. Finally, a fuzzy rule set is established according to the samples mapped by the support vector. The simulation results based on industrial data show that the proposed method has better control performance than conventional fuzzy control and proportional–integral–derivative (PID) control.

Apr 1, 2024

By S. Rideout

The United States Department of the Interior's Office of Surface Mining (OSM) is responsible for regulating active coal mining and reclaiming abandoned coal mines in the United States. In working with the State government agencies that implement these programs, OSM is building a new approach that moves away from traditional "command and control" regulation and towards an approach that focuses on providing long-term environmental and economic sustainability on lands disturbed by coal mining. This initiative called "Reclaim the Future!" looks to enhance opportunities for economic development, wildlife preservation and enhancement, reforestation, and other beneficial and productive uses of lands disturbed by coal mining. The initiative is also focused on ensuring that the landowners and the local public have significant involvement in determining how best to reclaim mine sites and what post-mining land uses are most appropriate for each individual abandoned mine reclamation project or active mine reclamation. Through the use of the best scientific input in an open, participatory process, OSM hopes to further sustainable development principles for coal mining within the framework of existing United States law.

Jan 1, 2007

By R. Woods

INTRODUCTION Gaudin (1), considered that "the mechanism of mineral collection is the central problem of flotation theory". From their work on adsorption phenomena in flotation for more than fifty years (2), Gaudin and his co-workers have made major contributions to the elucidation of this mechanism, a fact acknowledged by their contemporaries in the field (e.g. (3)). Their investigations in a number of areas, e.g. demonstrating that submonolayer quantities of adsorbed collector species can induce flotation, or identifying the influence of substances which can activate or depress (1), have helped to provide the basis for and the development of a theory to account for the interaction between mineral and collector. It was established in the late fifties (4) that the presence of oxygen is a prerequisite for the flotation of metal sulfides with thiol collectors. This fact rendered inadequate the concept of simple ion adsorption being responsible for rendering these minerals hydrophobic. The requirement for oxygen has been explained (1) in terms of this species being a component in chemical reactions between the sulfide surface and the collector. Gaudin has been instrumental in identifying the products of chemical reactions at sulfide minerals (1.5), a line of work which has been continued particularly by Finkelstein and co-workers in South Africa (6). In presenting a detailed mechanism of the mineral-collector- oxygen interaction, it has often been considered that the mineral surface - must first be oxidized to a metal oxy-sulfur species which

Jan 1, 1976

By Thomas J. Neil, O&apos

Most analysts find that progress has been evolutionary in any technologic field. To be sure, a few discrete breakthroughs can usually be identified, but viewed in its entirety, the curve of technologic progress over time tends to be relatively smooth with few discontinuities. Even in those cases where a major scientific discovery is achieved, the rate of technologic progress is limited by the often surprisingly slow rate of commercializing the concept into usable products. Whereas discovery and invention tend to be discrete events, technical innovation is often a painfully slow process. In spite of overall gradual change, technologic progress in most fields, when viewed in retrospect, tends to reveal certain relatively homogeneous periods where little change is evident, separated by episodes of accelerated progress. Thus, open-pit mining over the past century has changed from predominately train haulage to truck haulage and is now experiencing a major increase in belt haulage. Ore reserve estimation is another field that fits the same pattern, and the history of mine evaluation lends itself to a similar analysis. Evaluating mine investment opportunities is a fascinating aspect of mining. The unique set of risks inherent to every mining project is particularly intriguing. Geologic risks are most obvious, since faulty ore grade and tonnage estimates are among the leading causes of mine failures. Wide swine's in mineral commodity prices are usually cited as another major risk in mining. Because any ore deposit is a finite resource and the miner has limited discretion in selecting a mining sequence, mines are generally at the mercy of notoriously fickle commodity markets. There is a tendency for many mine investment analysts to feel that mineral market uncertainties are unprecedented in severity. Of course, prices in other markets rise and fall also-in some cases as precipitously as with minerals. However, two other mining characteristics tend to compound this marketing risk. First, the preproduction development period for a new mine is characteristically long. Under extremely favorable conditions, a significant mine may be developed in as little as two years, but the norm is four to six years or more. Second, mining is among the most capital intensive industries, consistently ranking near the top among all industrial sectors in assets per employee, and near the bottom in annual sales dollars per dollar of assets. Thus, mine investors typically have large sums invested for a long time before the outcome of the venture is determined by notoriously unpredictable markets. This is not a business for the faint of heart, and the importance of sound investment decision making is obvious. The high risk and technical complexity of mining operations have combined to require greater attention to financial evaluation by mining engineers than by most engineers in other specialties. Nearly all early mining engineering textbooks dealt with problems in mine valuation in a detailed manner; and, today, the sophistication of capital investment analysis is high in the mineral industries. Traditional Mine Valuation Methods Although some evaluation process has no doubt accompanied nearly every mine development throughout history, a formalized quantitative approach first emerged in the last half of the 19th century with the establishment of academic programs in mining engineering. The philosophy and approach to mine valuation that evolved at this time were, with periodic minor refinements, considered the standard for nearly a century. Only after 1960 did major changes begin to occur. The traditional approach to mine valuation reflected the investment community's historic attitudes toward risk. Mines were generally considered too risky for debt financing, and virtually every new mine was financed from internally generated funds or new equity subscriptions. The investment evaluation methods that evolved focused on mining's higher risk relative to other

Jan 11, 1982

By E. Robert Kiehl

In the early days of the United States, gypsum was most commonly used for the manufacture of plasters with energy being used for quarrying, grinding, and calcining of gypsum rock. With the dramatic switch to gypsum-drywall construction after World War II, the energy usage per ton of rock processed increased more than threefold, and with the rapid growth of the construction industry, the total energy consumption in gypsum-board production alone increased eightfold during the period from 1940 to 1973. The gypsum industry was one of the first to recognize the need for energy conservation and has voluntarily reported its progress to the Federal Energy Administration for the past several years. Efficiencies in the use of energy have resulted in decreasing the unit consumption an estimated 10 percent during the past six years. Improved combustion efficiencies, optimum operating conditions, more liberal use of insulation, and heat recovery will all contribute to the gypsum industry's goal of using less energy. Gypsum products today are vital to over 85 percent of new housing construction in the United States.

Jan 1, 1978

By R. K. Paramguru, K. Srinivasa Rao

This paper describes a new approach for examining the kinetics and mechanism of zinc dissolution from sphalerite concentrate in acidic ferric sulfate solution in the presence of manganese dioxide. A literature search was performed to access the possible action of the two oxidizing agents, i.e., ferric ion and manganese dioxide. The possibility of galvanic coupling between ZnS and MnO2 and the cyclic action of the redox couple, Fe2+/Fe3+, on these two minerals were theoretically examined based on corrosion principles. Expressions for the mixed potential (Em) and the mixed current (im) were derived for the relevant corrosion and galvanic couples. Leaching experiments were conducted to establish which of the above phenomena is operative during leaching. The results indicated that the dissolution mostly occurs by the action of ferric ion on ins producing ferrous ions. The presence of MnO2 enables a quick conversion of ferrous to ferric, which maintains the rate of in dissolution. The process has promising features for commercial exploitation.

Jan 1, 1999

By Bruce E. Holbein, Dennis K. Kidby, Ann L. Huber

World gold production figures and the processes used for gold production indicate a high dependence on both cyanide leaching and carbon adsorption metallurgies. Problems associated with the use of carbon in the treatment of refractory ores as well as economic and environmental considerations associated with the use of cyanide point to the advantages that can be realized through the use of more efficient gold adsorption media and with cyanide recovery. We have developed a process termed AurosaveTM-1 which provides a number of advantages through the use of a new synthetic robust gold adsorption medium, termed Vitrokele TM V-911. This process allows further recovery of gold from a variety of ores and allows for a simplified process for use not involving thermal regeneration or high pressure elution. We have also developed a cyanide recovery process termed Cyanosave ™ which uses Vitrokele TM V-911 and allows efficient recovery of cyanides from decants or tailings and re-use of recovered cyanide. This obviates the high chemical expenses for cyanide destruction where environmental issues require such water and tailings management.

Jan 1, 1998

The need for geological control in orebody estimation and modelling is self- evident to geologists and mining engineers engaged in practical day-to-day estimation. It is only fairly recently, however, that attempts have been made to incorporate explicitly such requirements into published accounts of geostatistical estimation; see, for example, Dowd and Scott (1982, 19841, Rendu and Readdy (1982), Dagbert et al. (1984), Dowd (1984), Benest and Winter (1984). In practice, many geological controls in automatic or semi-automatic estimation and modelling are essentially geometrical controls. The aim of this paper is to present two techniques for geological/geometrical control. Whilst the applications are new, neither technique is entirely original and both have been adapted from other fields and sources. Both techniques are, in some sense, types of estimators and/or interpolators of shapes. The first is a method for fitting spline surfaces to control orebody boundary estimation and to unroll orebodies. The second is an application of Minkowski addition to interpolate shapes such as orebody outlines or stope boundaries and to control estimations.

Jan 1, 1986

By N. D. Jagger, I. M. Arbuthnot

The recovery and destruction of cyanide in gold tailings is currently a topic of great interest for both financial and environmental reasons. The environmental problem is particularly important in the U.S.A. at present with the environmental lobby waging a campaign to eliminate the problem of migratory birds dying after drinking tailings dam wate. Tough legislation with severe fines and jail sentences for company executives have been introduced in several states for exceeding cyanide limits. To reduce cyanide levels in tailings dams chemical treatment, including acidification, alkaline chlorination, the INCO sulphur dioxide oxidation process and the Degussa hydrogen peroxide process amongst others are being. used. In addition several processes are at various stages of development for the recovery of residual cyanide from gold tailings. Among these is the process developed by Cyprus Gold and pilot tested by DSIR Industrial Development. This process uses air to strip cyanide from the acidified barren pulp and will be used at Cyprus Gold Mines Golden Cross Mine on the Coromandel Peninsula in New Zealand (Fricker & OWers 1990).

Jan 1, 1991

By T. J. Lyman, M. J. Robison, W. A. Ruemmele

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km (4.4 miles) of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A171, the Wilshire/Alvarado Line, involves tunnel construction beneath 7th/Street from the 7th/Flower Station to the Wilshire/Alvarado Station. The project consists of the excavation and lininig of 3000 m (9900 ft) of twin-bore, 6.7 m (22 ft) excavated diameter, 5.5 m (18 ft) finished diameter subway tunnels. The location of the project is shown in Figure 1. The majority of the excavation passed through weak siltstone/ claystone bedrock; although, portions of each tunnel approaching the 7th/Flower Station passed through fine-grained alluvium. Both tunnels were excavated with a digger shield. The project also included the excavation and lining of 6 cross passages, 2 communication rooms and a sump, all at tunnel grade between the two bores. A program of geotechnical instrumentation and building monitoring was performed to detect and document the response of the ground and adjacent structures and facilities to tunnel excavation. The instrumentation program was also intended to provide information that would permit implementation of remedial measures, when and as required, to prevent damage to structures, facilities and utilities along the tunnel alignment. The purpose of this paper is to discuss the ground response to tunneling on Los Angeles Metro Rail Contract A171. This paper presents a description of the tunnel project, the excavation and support method used in construction, the subsurface geology, and

Jan 1, 1989

By Emily Wortman-Wunder

As the 2011 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2011 issue of the Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 330. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2011 Transactions is the second Transactions to take advantage of new publication technologies. It appears solely in electronic format. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will better serve the mining community. Based on the feedback from the 2010 Transactions in e-book format, I believe that the transition to the all-digital format was the proper decision. The 2011 Transactions contain some of the most interesting research from the past year, including a 10-year profile of roof and rib fall trends from the National Institute of Occupational Safety and Health (NIOSH) and a new cross-disciplinary application of the tools of epidemiology to assess and mitigate risk in coal mines . This 2011 Transactions comprise of a total of 82 technical papers (626 pages including index), including all 19 papers published in 2011 in the Technical Papers Section of Mining Engineering magazine (Vol. 63) and all 32 papers published in 2011 in Minerals & Metallurgical Processing (Vol. 28). Additionally, this volume contains 31 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 82 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2011 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2011

By E. W. Geist

This paper is presented from the viewpoint of the mill operator and maintenance supervisor. Its purpose is to highlight the things that have been accomplished by the mill designers to lighten the load for the maintenance superintendent and to reduce the overall costs for the plant operator. The complexity of plant design, the civil and structural engineering problems encountered when the satisfactory maintenance layout is accomplished are appreciated, and the writer is fully aware of the complexities of these problems. However, it is not the purpose of this particular paper to dwell upon these problems, nor to emphasize or de-emphasize the problems of the civil, mechanical and electrical engineers. It is simply that the paper will attempt to review what these people have accomplished in spite of the many technical problems. This paper then is prepared with the operator and maintenance people?s viewpoint. What is their definition of design for maintenance? It is the writer's interpretation that the various design concepts which mean improved maintenance are such items as (I) maintenance areas, (2) laydown space for maintenance materials in specific maintenance jobs, (3) the inclusion of bridge cranes in the plant and specific design of the craneways to accomplish flexibilities for the cranes, and (4) the location of the piece of equipment to allow maintenance people to work around the equipment - - - this specifically includes the orientation of the particular piece of equipment.

Jan 1, 1967

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By Earl Cook

Introduction Men like physical power because it gives control over nature and over other men. Physical power comes in two common forms: explosive and non-explosive. In both forms, the most powerful devices yet invented make use of nuclear energy: on the one hand, the hydrogen or fusion bomb, and, on the other hand, a nuclear power plant. For some nations, nuclear power offers a measure of independence not otherwise available in a time of diminishing and unevenly allocated fossil fuels. Consequently, it has great attraction. Unfortunately, the application of nuclear energy (especially fission energy) to either explosive or electrical power entails a singular risk, that of injury from ionizing radiation, both natural and induced; this risk is found in all stages of the nuclear-fuel cycle, from mining of fissionable materials to the disposal of wastes produced in the "burning" of nuclear fuels. The health costs of nuclear power were not fully assessed in the early stages of the development of nuclear technology and some of them were not properly guarded against, either in the USA, which led the world into the nuclear age, or in Canada, which followed an independent path. What I shall do in this paper is to sketch the history of nuclear regulation in our two countries, to point out what I consider similarities and differences, and to suggest that regulatory history, as perceived by a concerned public, has a great deal to do with what is possible today and probable tomorrow, in other words, with public acceptance or rejection of the nuclear option. The U.S. situation As we sow, so shall we reap. In the USA, further expansion of the nuclearpower industry has been almost stymied by government actions that reflect mounting public concern. There is no national storage facility for spent reactor fuel and it has been decided not to reprocess it; consequently, existing power plants are about to choke on their own wastes. Since the Three Mile Island accident, no new nuclear plants have received operating licenses, although several are ready to start up. The uncertainty of future government action has caused the abandonment of plans for a number of new nuclear plants. In addition, many research projects related to medicine and agriculture, which produce low-level radioactive wastes, are about to be shut down for lack of licensed disposal facilities. Some would maintain that this situation has come about because of the low benefit-to-cost

Jan 1, 1980

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: 1) as a diverse group of fine-grained minerals, 2) as a rock term, and 3) as a particle size term. As a rock term, clay is difficult to define because of the wide variety of materials that comprise it; therefore, the definition must be general. Clay is a natural, earthy, fine grained material comprised largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates comprised mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic, e.g., halloysite and flint clay. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 pm. as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 pm. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1988, 1989, and 1990 productions according to the US Bureau of Mines (Ampian, 1992). As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this section these commodities are organized as follows: 1) bentonite, 2) common clay, 3) hormites, and 4) kaolin. Fuller's earth is discussed in both the bentonite and hormite chapters. Fuller's earth is a term based on use, and both bentonites and hormites are sold as fuller's earth. The overlapping is particularly evident where both bentonite and non-bentonite fuller's earth are used for the same purposes or products, such as in drilling mud, bleaching or clarifying fats and oils, and carriers for insecticides and fertilizers. Kaolin, ball clay, halloysite, and refractory clays are grouped together because they consist mainly of minerals of the kaolin group. Common clay is a grouping of several fine-grained materials, including shale, sometimes referred to as miscellaneous clay. The scientific and technological publications pertaining to clays

Jan 1, 1994

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

By Jörg Weidemann, Peter W. Kuchar, Paul Burgwinkel

The West German Ruhrkohle AG and the engineering company BEDIA have developed an emission control system for diesel engines that is suitable for use in underground coal mining, consisting of a granular catalytic converter and a dry cooling system. Its first ever application was to a diesel mining locomotive. In the catalytic converter the exhaust gases pass over porous, platinum-covered ceramic balls in a double tube, oxidizing CO to CO2. Simultaneously, soot particles in the gases are subjected to afterburning. Laboratory tests carried out by BEDIA and at Aachen University of Technology showed that there was a reduction of over 80% in the CO content of the exhaust gases and over 30% in soot emission. The dry cooling system fulfills all the requirements demanded of exhaust cooling underground and does not have the disadvantages of conventional systems. It needs little maintenance, and it is light and compact. The most important components are a waterjacketed exhaust manifold, a tube and shell heat exchanger, a new type of flame arrestor in a stacked crimped ribbon design and a Venturi diluter. The system has its own thermostatically-controlled cooling circuit to keep the exhaust temperature between 120° C and 150° C, thus effectively preventing the tubes becoming blocked up.

Jan 1, 1989

By G. Brien, O&apos

Selective in-plant breakage was investigated at a Central Queensland, Australia mine. Component seams and size fractions from in-plant samples were characterized petrographically and probability analysis of vitrinite reflectance data used to track the distribution of seam proportions through the plant. Results show that the 2 seams reported differentially to coarse and fine circuits, mainly as a function of coal type rather than rank. Seams were also preferentially concentrated in different size fractions of the coarse circuit. Breakage in the coarse coal centrifuge generated approximately 4% of -0.5 mm fines, but was not seam specific.

Jan 1, 1996