Search Documents

By Carl P. Venzke

Mining lignite in the Gulf Coast often requires some interaction with shallow ground water system. Suggestions for determining ground water data and analysis requirements for regulatory compliance are given. Simple methods for estimating mine inflow seepage, ground water level declines, and changes in ground water chemistry, which may result from mining, are discussed. The mining of lignite often results in interaction with shallow ground water systems. An evaluation of the interaction is required as input to mine permitting and engineering. Your evaluation will proceed more smoothly and produce more meaningful results with some planning prior to performing your evaluation. The following are tips to consider in planning and carrying out a successful study.

Jan 1, 1982

By Ronald L. Haxby

This report presents a refractive seismic technique for evaluating the strength of rock within an open pit bench. A concept of correlating rock strength and seismic velocity is discussed and a method of predicting the degree of fragmentation of a pit bench is introduced, Figure 1 shows the area of interests [ ] Most of the work was performed while completing graduate studies at the University of Arizona.

Jan 1, 1967

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By Katherine Hynard, Colin Eustace

Suboptimal decisions introduced during the mine planning process are generally a consequence of both a myopic view of planning objectives as well as time and resources available to convert longer-term plans into execution plans. Erosion of strategic mine plan value in conversion to execution plans is likely to amount to billions of dollars each year. When integrated with operations data feeds, simulation and optimization tools can be used to preserve the value in the strategic mine plan. Optimization models are capable of both automating production of execution plans and improving performance. This reduces the manual burden of revising plans while improving alignment with long-term production objectives. Simulation models can also support the process of developing effective execution plans by providing forward visibility of mine operations performance. They can also be used to test the robustness of optimized execution plans and response to operational variability and disturbances.

May 1, 2025

By B. A. Wills

Much research effort has been spent in attempting to reduce the high energy costs in grinding, but relatively little in developing methods to enhance the liberation of the minerals from each other. This paper presents some ideas on the nature and role of grain boundaries in mineral assemblies, and their influence on the propagation of cracks through the rock. It is argued that if the mechanisms of fracture are more clearly understood, crack propagation may be controlled in such a way that intergranular fracture dominates breakage, producing less fines and a higher degree of liberation.

Jan 1, 1995

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By Neil J. Dahmen, Howard J. Handewith

INTRODUCTION Tunneling machines were introduced into civil con¬struction in the 1800s, but their practical applications were not realized fully until the 1950s. As of 1977, tunneling machines were being used on most tunneling projects of substantial size. As in civil construction, the mining applications of tunneling machines have included long drives such as tunneling for long ore-body develop¬ment drifts, long haulage tunnels, longwall access drifts, and long crosscut developments. Tunneling machines ranging from 1.75-m (5.7-ft) to more than I1.0-m (36-ft) diam are available from several manufacturers; machines for mining applications generally have ranged between 1.75 and 6.0-m (5.7¬and 20.0-ft) diam. Tunneling machines usually operate at or near horizontal grades and are supported by a rail-haulage backup system. However, declines and inclines have been made using alternative backup equip¬ment. Either circular or shaped tunnels may be bored, depending upon the particular equipment used. Using tunneling machines to bore openings through rock offers several advantages over the use of the drilling and blasting technique. These advantages include a rapid advance, continuous operation, uniformity of the opening size, smooth walls, and safe working conditions. Compared to drilling and blasting, boring reduces the disturbance of adjacent rock, thereby reducing the ground-support requirements and the exposure to water inflows. The smooth walls provide natural arching and present minimum resistance to the flow of air. A tunneling machine should be considered a spe¬cialized mining tool that is well-suited to certain mining applications. Properly applied and sustained, a tunnel¬ing machine contributes to realizing substantial econo¬mies in the development of underground mines. All costs herein are expressed in 1977 US dollars, unless otherwise noted. The mention of trade names and manufacturers is not intended to imply an endorse¬ment of any specific equipment. TYPES OF TUNNELING MACHINES As listed in Table 1, five principal types of tunneling machines were being manufactured in 1977. Each type of machine offers a special solution to a specific mining problem. Although each of these types of machines is described herein, most of this chapter is devoted to the full-face rotary rock-tunneling machine that has demon¬strated the greatest production in both civil construction and mining applications. Full-Face Rotary Rock-Tunneling Machines As shown in Fig. 1, a full-face rotary rock-tunneling machine consists of a rotating head that is fitted with rock-cutting tools and is forced into the tunnel face. This head is supported by a bearing on a structural support member that, in turn, is held in place by a hydraulically positioned wall-gripping mechanism. Both torque and thrust are reacted from the cutterhead, through the structural support and gripper mechanism, and to the tunnel wall. The rock cuttings fall to the invert at the tunnel face, and they are removed by means of cutterhead buckets or scoops that transfer the cuttings to a conveyor belt. After advancing the cutter¬head through a preset boring stroke, the tunneling machine is advanced by hydraulically pulling the gripper mechanism in from the tunnel walls, stroking forward, and resetting the gripper to the new forward position on the wall; the machine then is set for the next advance stroke. Full-face machines cut only circular openings. Ma¬chines with diameters as small as 1.8 m (6 ft) and as large as 6.1 m (20 ft) have been used in mining applica¬tions, excavating rock with unconfined compressive strengths in excess of 276 000 kPa (40,000 psi). Although special machines have been designed to turn on a radius of 30 m (100 ft) in both horizontal and vertical directions, the conveyors and backup sup¬port equipment generally limit tunneling machines to turns with a radius of more than 60 m (200 ft). The full-face rotary rock-tunneling machines have provided the fastest and most reliable production of any mining method or machine. These machines can be equipped to place any of a variety of ground-support systems, and they can be provided as "open" machines, as shown in Fig. 1, or as "shielded" machines, as shown in Fig. 2. The open machines have the advantage of allowing the ground to be supported as near to the tunnel face as possible. The shielded machines have been designed principally to allow placing precast con¬crete segments. The shielded machines completely pro¬tect the equipment and personnel at the heading, but they are economically limited to permanent long-life haulageways where full lining is required. Partial-Face Rotary Rock-Tunneling Machines As shown in Fig. 3, the partial-face rotary tunneling machine is equipped with a cutterhead that rotates slowly at about 0.21 rad/s (2.0 rpm). The single-disk cutterhead produces the tunnel section shown in Fig. 4 by means of an oscillating motion. These machines work on the undercutting principle, and they are avail¬able in spring-line dimensional increments of 0.1 m (0.32 ft) from 1.5 to 2.1 m (5.0 to 7.0 ft); the vertical dimensions are 2.4 to 3.2 m (8.0 to 10.5 ft), respec¬tively. Depending upon the tunnel width, the cutterhead disk may be fitted with from 8 to 16 drag-bit cutters. Penetration is achieved by means of hydraulic rams that force the tungsten-carbide bits into the rock mass. The operation is cyclic, with cutting occurring only on the upstroke. On the downstroke, the rotating cutter¬head draws the fallen muck from the invert into the panzer-type conveyor for rearward transfer. This feature allows time to either reposition ore cars or to exit the tunnel with muck trains while the machine is cutting, as shown in Fig. 5. Boom-Type Rotary Excavators The boom-type rotary-excavator tunneling machines commonly are known as boom-type continuous miners

Jan 1, 1982

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By Philip G. Meikle

The Bureau of Mines Coal Mining Technology program has developed new concepts aimed at improving the efficiency of underground coal product ion. Conceptual designs have resulted in equipment prototypes, some of which are currently undergoing proof-of-concept evaluations at Bureau and cooperator facilities. Several of these systems and concepts are described.

Jan 1, 1984

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By R. K. Singhal

The underground coal mining systems have kept pace with the developments that have occurred in other types of mining industry. A diversified group of machines with high horsepower motors, built-in microprocessor technology and with numerous options to satisfy the miners need in a varying geological environment are now available. A brief review of this existing technology and its likely status within the next 21 years is presented. Discussed also are some of the on-going advanced developments in electronic mechanization, remote control and automation together with mine wide data monitoring and management systems and facilities to process and transmit data to remote computerized stations.

Jan 1, 1989

By John K. Hammes

This paper has been written as one of a group of papers dealing with the subject "Cost Elements in Mining". What are cost elements in mining? The mine operator thinks of direct mining costs in terms of labor, materials, supplies and power, and we might define cost more generally as the price paid to acquire or produce something. Economic theory also has its concepts of cost. From one point of view, that of the consumer, the cost of mineral commodities might be viewed as the total price industry pays for mine output. Similarly, the mining company engaged in the on-going business of finding, developing and operating new mines is concerned very much today with the distribution of all the revenue paid for mine output and not just with its direct or controllable cash costs. In other words, what will the labor force, the supplier of energy, explosives, and reagents, and the supplier of government services, management, capital and the ore reserves receive for their contribution to production.

Jan 1, 1974

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977

By John E. Crawford

A year ago, if I had the pleasure of addressing you, I would have discussed ocean mineral resources from a promotional standpoint. I would have described exciting indications of mammoth tonnages of sea-floor industrial minerals. I would have attempted to fire your imaginations as to the potential of a nation having the technologic know-how to exploit its submerged boundaries. As a first step toward this capability, I would have solicited your support for a Bureau of Mines? program aimed at determining the industrial worth of marine minerals and devising techniques and hard- ware for their recovery. We still need your support, but recently we have ventured out of the realm of planning and into your Government's first program in marine mineral engineering. Today, I wish to describe what we have done within the framework of existing research problems and our possible goals. I will be brief so as to allow ample time for questions, and I can do this with confidence because our program is so new that I need not be chagrined at not having all the answers.

Jan 1, 1965

By Herbert P. Haschke

I. Changes made by the Economic Recovery Tax Act of 1981 (ERTA) which have an effect on investing in tax shelter investments A. Maximum ordinary income tax rate on individuals is now 50%. B. Maximum tax rate on long-term capital gains for individuals is now 20%. C. Maximum tax rate on alternative minimum taxable income for individuals is now 20%. D. Although not changed, the "add-on" 15% minimum tax on tax preference items and the possibility of paying the alternative minimum tax cause individual U.S. income tax planning to continue to be very complex. II. Real Estate A. The new Accelerated Cost Recovery System of depreciation (ACRS). 1. Mandatory for assets placed in service after 1980. ACRS will eliminate most if not all controversies with the IRS over depreciation. 2. Real property now depreciated over 15 years. Component depreciation is not available. 3. Accelerated depreciation is available - a 175% declining balance method with an automatic shift to straight line method at the optimum point in the asset's life. Alternatively, a taxpayer can elect to use the straight line method.

Jan 1, 1982

By Mustafa Kumral, Mehmet Balci

Strategic mine planning focuses on cutoff grade selection, capacity planning and block sequencing. Despite significant knowledge accumulated, potential value can be added to mineral sourcing by addressing various aspects. A case study on a metallic deposit with a lognormal grade distribution examines if grade/metal distribution influences cutoff grade selection. Six data sets with different shape and scale factors, but the same ore tonnage and metal quantity, are analyzed. Results indicate deposits with lower shape and scale factors are more sensitive to metal price and discount rate changes. The study also investigates the effect of economies of scale (EoS) on project value, focusing on the ratio of variable cost to total cost (capacity factor). Two regression analyses are conducted for optimal capacity planning and cutoff grade selection. The first shows capacity planning is highly sensitive to the EoS of mining and mineral-processing costs, with grade variability and metal distribution being negligible. In the second analysis, grade variability and EoS of mineral processing costs are vital for cutoff grade selection.

Sep 1, 2024

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By T. M. Sukel

Engelhard Corporation is one of the leading producers of kaolin based products in the world, having acquired the assets of Freeport Kaolin company in 1985. Much of the production technology used in the kaolin industry was pioneered by Engelhard and Freeport, including Ultraflotation for improving product brightness, delamination to produce kaolin platelet products, calcination to produce ANSILEX® high opacity titanium dioxide pigment extender and pipeline slurry operations to economically transport kaolin from the mine to beneficiation facilities. Engelhard traces its roots back to 1870 when the Edgar family discovered kaolin behind their property in Bonhamtown, New Jersey. Today the company produces the broadest line of premium coating pigments with extensive sales throughout the world. The international scope of the company's business has led Engelhard to evaluate kaolin deposits throughout the world as possible grass roots production sites. Most kaolin products are used in the paper industry -- the largest volume end-user 80% of the total market -- as filler and coating pigments. Lower volume specialized applications include fillers and reinforcements for plastics and TiO2 extender pigments for paints and coatings.

Jan 1, 1987

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988