Search Documents

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By L. Shevenell

Nevada now has, or will have, 35 pit lakes resulting from open-pit mining below the water table. State regulators are requiring that the ultimate pit lake water quality be predicted as part of the permit application process. Water balances/pit lake filling rates must be esti¬mated in support of the geochemical modeling. In Nevada, analytical and numerical methods have been employed for the study of pit lakes. In the current work, analytical solutions are investigated for one pit lake, the Getchell south pit lake, which previously filled be¬tween 1968 and 1982 during a hiatus in mining. Water levels vs. time are available for this lake and these data have been fitted with a hyperbolic curve. This water-level-vs.-time curve was used in simple water-balance computations to find the net inflow rates by forcing computed water levels and volumes to match those of the known water levels and volumes through time. The model described here provides realistic volume fluxes into and out of the lake on a monthly basis as the pit lake filled.

Jan 1, 2000

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989

By R. W. Lai

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of coal pyrite and mineral pyrite.

Jan 1, 1989

By E. J. Miller

The Ventilation Branch is engaged in a project to determine if low level carbon monoxide monitors used for early detection and warning of fire in a coal mine conveyor belt entry can provide protection equivalent to that of thermally actuated point type heat sensors commonly used for fire detection. A series of tests were conducted to determine the required operating parameters, such as sensor spacing and alarm levels of detected carbon monoxide to provide equivalency between' these methods of fire detection. This report summarizes the results of these tests.

Jan 1, 1980

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By William Highton

If the economic situation in the Western World evolves on a path similar to that of the past decade, then we Mining Engineers must accept that one of the major cost factors in the production of deep mined coal is going to be that of labour. Whilst not trying to over-simplify matters it does appear that one of the ways of maintaining acceptable coal costs is by obtaining more coal without increasing manpower. One such way could be an increase in the use of the retreat method of mining. The paper theorises and illustrates case studies to show that as the Mining Industry extends the use of Longwall retreat mining systems in coal seams where the risk of spontaneous combustion exists, then the use of bleeder entries should be questioned. In addition to the spontaneous combustion risk, bleeder entry systems where the ventilation flow is not fully controllable cannot be construed as a safe and reliable method of controlling high rates of methane emission. These two major aspects alone should be sufficient ground for Mining Engineers to re-consider the practice of using bleeder entries. An alternative "The Back Return System" appears to offer most of the advantages for controlling the environment, without the disadvantages of the other system.

Jan 1, 1980

By Mahesh C. Jha, Frank J. Smit

Column flotation and selective agglomeration are promising advanced physical cleaning processes that can be developed for preparing premium quality coal-water slurry fuel from coal fines. Such a fuel could either replace oil or natural gas in certain industrial and utility boilers or else could be burned in advanced combustors currently under development. These applications require coal cleaned to sulfur and ash contents below 258 g/GJ and 430 - 860 g/GJ (0.6 lb/million Btu and 1 - 2 lb/million Btu), respectively, to meet clean air emission requirements. A highly loaded slurry must be produced in order to avoid derating the boilers, and the total cost of the fuel must be below $2.37/GJ ($2.50/million Btu) in order to penetrate the market by the turn of the century. Achieving these technical and economic goals depend critically on the selection of suitable feed coals. This paper describes the identification and evaluation of 18 coals and final selection of six coals from different regions of the United States as potential feedstock for preparation of premium fuel. The work is being performed under a cost-shared DOE project.

Jan 1, 1995

By D. Scott Barr

Whole ore roasting using oxygen fluid bed systems was selected for two roasting facilities constructed for Independence Mining Company Inc. in 1989. Independence Mining Company Inc. (formerly Freeport-McMoRan Gold Company) processes refractory gold ores at two facilities located 60 miles north of Elko, Nevada. The Jerritt Canyon project, a joint venture with FMC Gold Inc, processes 2.8 million tons per year of carbonaceous refractory ore by oxygen fluid bed roasting and aqueous chlorination. The fluid bed roasters have been in operation since July, 1989. The Big Springs project has processed 400,000 tons per year of sulfide refractory ore since May 1989 from the Big Springs Joint Venture between Independence and Bull Run Gold Mines, Ltd.. Freeport Research and Engineering of New Orleans, Louisiana was the developer of the innovative technology used in the oxygen fluid bed roasting systems and have been granted a patent on its use. Environmentally, the roasters have exceeded expectations with lower emissions than designed as measured in compliance testing for the State of Nevada.

Jan 1, 1990

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In practice, however, coal blending is, at best, coal mixing. The degree of blending sophistication required depends on the reason for coal blending in the first place. If it is to maintain fuel characteristics that will diminish the chance of slagging and fouling, then some swings in variability may be tolerated at some power stations. However, if emissions limits are the issue, then more sophistication may be needed. Emissions limits are becoming stricter with requirements to meet averages for shorter time frames (hours and days instead of weeks and months). These restrictions require closer control over the quality of the blend being fed into the bunkers at the station. Even scrubbed units should have a consistent quality of fuel as feed so that sorbent additions can be minimized. To meet these challenges, engineers must consider available equipment and control techniques and the properties of the parent coals when evaluating new blending systems.

Jan 1, 1994

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials, and consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium (V). Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, Xray fluorescence (XRF) analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 weight percent V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples, calcium carbonates also significantly contribute to the V deportment, while wuestite, lime and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the Vbearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Aug 1, 2024

By S. B. Kim, J. Hong, K. Park, W. Kim, H. Kim, Y. Han, J. Choi

"For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50–200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.INTRODUCTION A great number of potential applications of lithium are being developed currently by the thermonuclear fusion power generation industry(1,2) as well as by the battery and fuel cell industry(3). Even though lithium is mainly consumed in the form of lithium metal and some lithium compounds, about 10% of total lithium production is consumed directly as mineral concentrates by the ceramic industry for the manufacture of special ceramics and mica based glass-ceramics(4). Granitic pegmatites normally contain feldspars, quartz, and mica in addition to lithium-bearing minerals such as spodumene (LiAl(SiO3)2), petalite (LiAlSi4O10), and lepidolite (KLi2Al(Al,Si)3O10(F,OH)2). The amount and grade of metallic minerals tend to gradually decrease and become lower, leading to the increase in the price of base metal or metallic compound(5). Accordingly, recent studies have been extensively devoted to developing the technique to improve the grade of metallic minerals from low grade metallic ores(6,7). Nevertheless, studies regarding the improvement of Li grade from lepidolite ores are very scarce. Lepidolite is a phyllosilicate mineral of the mica group and is often associated with other minerals such as calcite, muscovite, feldspar, and quartz, which need to be separated for lepidolite enrichment(8). Many studies have reported the flotation techniques for separating calcite, muscovite, feldspar, and/or quartz from various targeting minerals(9-11); however, there has been no attempt to investigate physico-chemical properties of lepidolite and its separation from such types of gangue minerals through flotation. Hence, in this study, for the first time, flotation has been carried out for the quaternary ammonium salts (stearyl trimethyl ammonium chloride (STAC, (CH3)3CH3(CH2)16NCl))-lepidolite system based on only the electrokinetic property of minerals that consist of lepidolite ores without adding any depressant to get an initial insight on its flotation behavior. The experimental variables that influence the lepidolite flotation such as amount of collectors, feed size and solution pH have been also examined."

Jan 1, 2015

By Liu Hanzhao, Jin Yongduo

Many gold ores which are not only submicroscopic but also rich in arsenic and organic carbon, for example Dongbeizhai Mine, have been found in china. These ores belong to the most refractory ores The key to the recovery of gold from these ores is preoxidation. Dongbeizhai ores have been tested with biooxidation, chlorination, double oxidation, acidic and alkaline pressure oxidation, catalytic oxidation, NITROX and roasting. To date it appears that either roasting or pressure oxidation is optimal. It is suggested that the flotation-roasting (or pressure oxidation)-CIL process should be used to treat this type of ore.

Jan 1, 1995

By H. L. Ehrlich

Modes of microbial attack of metal carbonates, metal silicates, metal oxides and metal sulfides are summarized. The current status of microbial redox mechanisms, whereby metals in metal oxides and sulfides are mobilized, is discussed. Opposing theories of a single mode of attack involving interaction with a microbially produced reductant or oxidant in the bulk phase and of dual modes of attack involving a reaction requiring physical contact between microbe and mineral surface on the one hand and microbial production of a reductant or oxidant in the bulk phase that reacts with the mineral on the other hand are considered. No one mode when finally completely unraveled should be expected to fit all cases. Some biochemical, electronmicroscopic and spectrophotometric approaches for elucidation of missing details of different modes are suggested. Key words: Bioleaching, Biobeneficiation, Metal mobilization

Jan 1, 2003

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By Antoon W. van der Vooren, Colin R. Phillips

A comparison of analytical models used to describe deposition in the first generation of lung bifurcations is presented. In order to allow testing of the mathematical models, experimental data were obtained from radon daughter deposition in simplified lung bifurcations. The experimental data for particles deposited by diffusional mechanisms is best described by the assumption of a thin concentration boundary layer at the entrance of a right circular tube. Other more complex models do not accurately describe the deposition of submicron particles. The angle of bifurcation was found to have a minor effect on deposition.

Jan 1, 1981