Search Documents

By P. C. Rath, K. Srinivasa Rao, T. Subbaiah

A process for the recovery of nickel from ammoniacal leach liquor through an integrated solvent extraction-electrowinning (SX-EW) flowsheet was tested on a pilot-plant scale. The objectives of the test run were to assess the reproducibility of laboratory-scale data in a large-scale continuous operation and to study the build up of impurities in the system. The pilot-plant test was conducted under operating conditions that were established from the laboratory-scale experiments. Efficiencies of nickel extraction, nickel stripping and ammonia scrubbing were comparable to the laboratory-scale values, whereas the current efficiency during nickel electrolysis was observed to be less than the laboratory-scale values. The electrodeposited nickel contained some cobalt and iron impurities.

Jan 1, 1998

By T. Shungu, N. Vermaut

The various copper-cobalt ores mined by Gecamines, together with typical plant applications and results, are briefly described. Intensive laboratory investigations have been undertaken in recent years to improve the metallurgical performances of the various concentrators. As a result of these tests, it was shown that the flotation of the siliceous oxide ores could be improved by increasing the efficiency of the palm oil collector (energetic conditioning, chemical emulsifier, petroleum sulfonate addition) and by varying the froth depth in the cells. A new flowsheet incorporating these modifications and a regrinding stage has been approved for the rehabilitation of the Kolwezi concentrator. For what affects dolomitic oxide ores, hydroxamates were tested as secondary collectors and, based on successful laboratory results, plant trials were run but failed due to excessive frothing. In other plant tests, xanthates were replaced by a xanthate- fatty acid mixture; plant trials over more than one year proved successful for copper, but not for cobalt. Mercaptans were tested as secondary collectors for the sulfides flotation from sulfide or mixed oxide-sulfide ores; laboratory results proved successful but, to date, no plant test has been run.

Jan 1, 1987

By A. M. Alfantazi, R. R. Moskalyk

Over the years, improvements have been made in the recovery of nonferrous metals, including improvements in the areas of mineral processing, pyrometallurgy and hydrometallurgy to extract cobalt as a byproduct from host minerals containing mainly nickel, copper and associated precious metals. At present, the technological emphasis is on solvent extraction coupled with electrowinning (SX-EW) for lateritic sources of supply within the Southern Hemisphere, such as in Australia and New Caledonia. Although sulfide-bearing ores, such as those found in Canada and Russia, will serve as a viable long-term source for cobalt, a ubiquitous metal, the future trend is anticipated to be in the implementation of compact and efficient SX-EW facilities that apply state-of-the -art innovation with environmental compliance This paper serves to collate the known practices for the recovery of market-grade cobalt by means of electrowinning from either an aqueous sulfate medium or chloride medium after upstream leaching, solvent-extraction and solution-purification procedures. For completeness, other commercial production techniques for the recovery of cobalt as a sulfide or oxide product are included in the summary of current cobalt processing practices.

Jan 1, 2000

By Kathleen A. Altman, Kevin Hegerle

FMC Gold Company start.ea processing ore at their Paradise Peak Mine in 1986. Gold, silver and mercury haye been produced from the Merrill-Crowe milling circuit and from heap leaching. There are three heap leach circuits, Paradise Peak, Ketchup Flat and County Line. The Paradise Peak and Ketchup Flat heap effluent solutions are routed into the zinc precipitation plant which is associated with the mill for recovery of the precious metals. The County Lne hea lech circuit is a stand-alone operation, again with a zinc precipitation recovery circuit. The mill was shut down in May, 1993 due to depletion of ore reserves with the remainder of the heap leach ore due to be placed on the leach pads by late summer of the same year.

Jan 1, 1993

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By Jan M. Mutmansky, David R. Kalasky

Computer simulation continues to be one of the most successful analytical applications of computers in the mining and mineral processing industries throughout the world. Through simulation, managers and engineers can explore the impact of new technologies, equipment designs, plans and operating strategies to improve their operations. It is not uncommon for a single simulation application to provide a quick payback of analysis expenses (within weeks or months) yielding long-term financial and operational dividends. The paper will present a summary of the types of software systems that are available for use on PCs and other computer systems. Support software for curve fitting, statistical analysis, and optimization of simulation models will also be presented. Methods of leveraging simulation efforts through networking and coupling of software systems will be discussed. Finally, the trends in simulation in the mineral industries will be analyzed. Areas of strength and weakness of simulation will be discussed along with the usefulness of commercial general-purpose and custom-writ- ten simulation packages. The future possibilities for simulation in the mineral industries will be outlined and predictions on trends for the future will be presented.

Jan 1, 1996

By S. A. Bunk, W. P. Wood

In the early 1980's BHP identified several potential gold deposits in West Africa. One of these deposits was located in Mali, near the village of Syama. As a result of extensive explo­ration activities, an oxide ore as well as an underlying sulphide ore was identified. After agreement with the government of Mali was reached the development of the deposit was undertak­en. The plan for the development of the mine included the treat­ment of the oxide ore followed by the treatment of the underly­ing transition and sulphide ore. The development of the deposit was extremely aggressive. Following the approval of the project in early 1989, engineer­ing was started, equipment purchased sitework was started, and the first ore was introduced in December of 1989. This was accomplished in spite of the difficulties of the site. These diffi­culties included: • remote site location without air or road or water access • no existing infrastructure including water, power, or communication • high health risks • limited construction and manufacturing support in West Africa The operation began with a conventional crushing/grind-ing/CIL/elution and electrowinning facility. The facility was designed to treat 2000 metric tonnes of ore per day. After start­up in December of 1989, the operation was improved to the point that plant throughput was averaging nearly 3000 tpd and running at 92 to 93% availability.

Jan 1, 1996

By W. DR. Fritz

Technical progress depends on strategic objectives and a concept showing how to benefit from the effects of novel techniques in an innovation process and how to implement them creatively in harmony with manpower capabilities. With the invention of prime movers, it was initially power engineering which dominated the development of industrial history before it was replaced by production techniques resulting from the more widespread use of machines. With the advances in the field of data processing and with the introduction of novel communication techniques, it is information technology- which today is having an ever increasing impact on technological progress. The main objectives of information technology in this context are a positive influence on the ?time? factor as well as the provision of tools to handle the complexity governing many operational processes through a concentration of information for the decision-making process. The German hardcoal industry became aware of the chances inherent in these new technological possibilities for the optimization of operational sequences and of decision-making and planning processes as a potential for success at an early stage and it has worked out a purposeful concept for their implementation.

Jan 1, 1992

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By Norbert Patzelt, Johann Knecht

INTRODUCTION Grinding mills have been used in the minerals processing industry for over 100 years. Their dimensions have grown continuously during this time. Besides increasing throughput rates of grinding plants due to the depletion of high grade ores, the lower specific in- vestment costs, as well as reduced operating and maintenance requirements are major reasons for this trend. When selecting new plant equipment one must consider that design principles which have proven their reliability on sizes of today's equipment do not automatically warrant a successful operation on the ever larger size of equipment. Modern calculation methods as for instance the Finite Element method already contribute considerably to the safe design of the huge equipment being built today and are a standard tool of the design engineers. More recently, modern computer programs are also being used in order to size the equipment to meet the process requirements. Today, two design principles are on the market - one which supports the weight of such a unit on trunnion bearings through cast conical endwalls and one which is supported through slipper pad bearings arranged at the circumference of the mill shell (Fig.1). The reason for the development of this alternative grinding mill design can be found in the past. During the sixties and seventies the growing sizes of ball mills with high LID ratios caused many mill failures due to cracked endwalls. The accuracy of the calculation methods as well as the quality standards for castings were not developed to a degree required for such kind of heavy equipment. One way to overcome these problems was the increase of the manufacturing quality standards as well as the introduction of the finite element method based on the analysis of the experience available. The biggest grinding mills being built today are large size SAG mills with cast conical endwalls and trunnion bearings (Fig.2). This is due to the fact that mill manufacturers who had come from the conventional ball mill design adopted these principles as well to their SAG mills. These grinding mills perform well without special concern to the operators. Other manufacturers overcame the problems as mentioned above by eliminating completely the heavy castings and trunnion bearings and the problems associated to it (Fig.1). This design was originally applied to ball mills for the mining and other industries. Due to the success of these shell supported ball mills, this design principle was also applied to SAG mills(Fig.3). Despite of the fact that the majority of today's grinding mills are built to the conventional design it is also interesting to have a look at this alternative. Principles which have proven their reliability on sizes of today's equipment do not automatically warrant a successful operation on the ever larger equipment if bigger mill sizes are realized only based on the pantograph principle. With growing grinding mill sizes, the mass and volume flows through the equipment increases rapidly. Thus it is very important not only to concentrate on the safe design of the structural components of the equipment but as well on the process requirements. The influence of the design on important process parameters of dry and wet grinding plants are discussed thereafter. It shall be shown how modern computer programs can assist in the optimization of the design of components in order to fulfil the operational requirements of such large size equipment. PROCESS REQUIREMENTS OF LARGE SIZE GRINDING MILLS Dry Grinding Mills The world's biggest ball mill is a dry grinding ball mill having a diameter of 6.2m and an overall length of 25,5m with a drive power of 11,200 KW or 15,000HP. This grinding mill dries and grinds gold ore at a rate of 500 tons per hour at a moisture content of up to 9,5%. As shown in Fig.4 this mill was built as a shell supported unit. In fact only this design principle allowed to meet the process requirement. This mill could hardly be built with cast conical endwalls due to the constraints of the trunnion bearings limiting the mill inlet. The following case shows how modern computer programs can help to meet the design criteria of the air system of large size dry grinding plants. For dry grinding plants, the gas flow through the SAG mill has to match the drying, as well as the material transportation require-

Jan 1, 1998

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont USA (Newmont) in Nevada was faced with such a need in their Carbon-in-Leach (CIL) train. In a collaborative effort between Newmont and Derrick Corporation, tests were conceived to assess the viability of drop in replacement screen using a three dimensional screen panel. The urethane pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade their urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing, and other scalping applications.INTRODUCTION In Spring of 2014, Process Machinery Associates (PMA), Derrick Corporation’s (Derrick) local area representative, met with Newmont USA (Newmont) to discuss the operation of the in tank screens in the carbon in leach (CIL) train at Twin Creeks, near Golconda, Nevada. The process was originally designed for 13,000 +tons per day (tpd) but has been steadily rising since the plant was commissioned and now Newmont requires 16,000 tpd to be processed. The original screens were running at their maximum capacity and Newmont required additional screening capacity to continue the upward trend in production. Physical separation by use of screening is one of mineral processing oldest methods. Screening media can be prone to blinding and pegging and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and therefore larger machines, screening media that doesn’t blind, or a combination of both. In an effort to avoid larger machines, Derrick Corporation had been working on a revolutionary three dimensional panel which would add non blinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 (Carlin, Nevada) in July of 2013 and was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By P. N. Bradbury

The coal companies of today have to make all of their in-the-field managers MAINTENANCE PRODUCTION MANAGERS. By using a computer application to monitor all aspects of the daily production as well as the maintenance, a company can immediately effect a cost reduction by studying the down-time and delay trends on an everyday basis. This paper will outline how a company can use a program to not only put a stop to the increasing supply and maintenance costs but start trimming each of these cost centers while actually increasing the efficiency and productivity of the current work force.

Jan 1, 1991

By J. L. Chakravatti

The movement of air from the surface, through the workings and then back to the surface, is the most important consideration in the ventilation design. The purpose of mine ventilation is seen as the maintenance of acceptable atmospheric environments wherever men work or travel underground; and acceptability is related to the risk of harmful biological responses associated with exposure to atmospheric environments in mines. In mine ventilation, a design engineer often has to contend with a number of problems not experienced to the same degree in other industrial situations; i.e. the vast extent of many workings - offering continuously moving work locations; the difficulty of predicting. inflows of contaminants to the airways which contain the micro-environment; and especially, the effect of mining activity within the duct system (e.g. mine roadways) carrying the airflow. Mining of uranium does not differ, in many respects, from the mining of other metals; the ore must be drilled, blasted and transported from the mine. Underground mining proceeds by the continous development and advancement of a network of passages and rooms or stopes from which ore is excavated. As in most mines, rock conditions and ore grades in uranium deposits very from area to area and between different mines. 1 In uranium mining, in addition to eliminating noxious gases from blasting, diesel equipment exhaust, and the control of dust, it is also necessary to dilute and remove radon, the gaseous element in the uranium chain and its decay products. Long term epidemiologic studies of United States uranium miners and that of miners in Czechoslovakia have confirmed that there is an association between excessive ex¬posure to radon daughters and an increased risk of lung cancer. The common practices for controlling these airborne contaminants are: (1) the circulation of large volumes of fresh air from surface to dilute these contaminants to a permissible concentration, and (2) the sealing of worked-out areas to prevent ingress of radon into ventilating air. 2 The sealing of worked-out areas can be easily and effectively accomplished, but the contaminants intro¬duced from the workings may raise the concentrations in the airways despite a good ventilation system and use of the maximum available amount of fresh air. The ventilating air can be strategically filtered to reduce dust and radon daughters to acceptable levels, and reused prior to final discharge. This strategy properly applied, will decrease the air colume requirements in certain marginal areas of the mine and thereby avoid an overall increase in the mine airflow. This is particularly advantageous in the cold climates of Canada, where the incoming fresh air must be heated in the winter months to a comfortable temperature, Thus, an economical and technically feasible air filtration system, strategically placed, can improve the underground mining environment and reduce the overall cost of ventilating the mines. In addition to affording flexibilty to the venti¬lation system, a potential saving of $1,500/m3/s/year would be realized if air is successfully cleaned and reused when compared with the conventional methods of generating an air current. 3 Denison is justly proud of its achievements in the air filtration technology development. This paper limits itself to an examination of the radiation control aspect of the air filtration strategy.

Jan 1, 1980

By Peter Mathias

The ventilation of long headings tunnels has al- ways posed special problems. The authors trace the progress of one such project from the design stage through the practical problems encountered to the final solution.

Jan 1, 1980

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By G. P. J. Schmitz, F. S. Gouws

In flotation processes the structure of the froth phase contains a wealth of information regarding the behaviour of the plant. Various structural features of the froth phase provide an indication of the froth viscosity, froth stability, mineral content, bubble size, etc., which can all in turn be related to the performance of the plant. In this paper the application of machine learning techniques to exploit information from digital images of the froth phase of industrial flotation plants is discussed. This includes both connectionist techniques to identify control decisions necessary to maintain optimal operation of the plant, as well as symbolic methods, such as induction techniques. Both approaches are used to classify froth structures based on statistical features derived from digitized images of the froth surfaces. It was found that backpropagation algorithms perform significantly better than either non-incremental or incremental induction. Backpropagation algorithms requires significant user input in order to optimally train the neural network as opposed to induction, which requires little user input. In contrast to back propagation, decision tree induction produces easily understandable decision trees which can be incorporated into a rule base or an expert system. Finally, incremental induction provides a simple means to smoothly and continuously adapt induced rules to follow changing process conditions.

Jan 1, 1996

By Ian M. Loomis, Malcolm J. McPherson

A fuel-rich fire exists when the quantity of fuel exceeds the oxygen available to support complete combustion. The transition of a mine fire from Oxygen- rich to Fuel-rich combustion, at this time, represents a point-of-no-return in the fire fighting efforts. Once the transition has been made to fuel-rich the fire can spread at a rate 6 to 10 times as fast as in the oxygen-rich state. Utilizing available technology the fire fighters are left to seal the fuel-rich fie as the only technique to extinguish it. In order to minimize the devastating effects of a fuel- rich fire it is important to understand the means by which the fire becomes fuel-rich and by what means the fire may be returned to an oxygen-rich state. This paper covers: the development mechanism of a fuel- rich fire in a coal mine entry and the physical and chemical effects of applying water to a fire. Experiments concerning these matters have been conducted in a 30 cm square wind tunnel constructed at the Virginia Polytechnic Institute and State University as a model coal mine entry. This paper also addresses the results obtained in testing application of a water mist to fuel-rich fires in this model. These tests have centered on the development profile of a fuel-rich fire in a duct and demonstrate a means of regaining control of a fuel-rich fire by returning it to an oxygen-rich state.

Jan 1, 1995

By D. A. Newman

The purpose of this research is to examine the post-failure behavior of coal as a mass and examine the relationship between the results of this study and prior laboratory investigations of the post-failure behavior of coal as a material. Instrumentation to measure changes in stress and deformation was placed in a headgate yield pillar and will be monitored as the face passes the area. A battery powered, automated data acquisition system, capable of recording up to 9,000 data points, is currently used to remotely monitor changes in vertical and horizontal pillar stress.

Jan 1, 1988

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997