Search Documents

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By James M. Kramer

This paper introduces an analytical approach for the determination of the vertical stress in the chain pillar system between two adjacent longwall panels. The development of this approach is based on the principles of fracture mechanics and superposition. Some empirical formulae have also been incorpomted into the development of the mathematical model. The mine entries and longwall gobs are treated as Mode I cracks in an infinite plate while the resistance of gob material and the characteristics of the pillar yield zone are considered as the distributed forces on the surface of the cracks. An user- friendly computer program has been developed to facilitate the calculation involved in this task. This approach is as accurate as the numerical analysis methods but requires much less expertise and computer hardware and software to apply

Jan 1, 1998

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By D. J. Reddish

This paper illustrates how numerical modelling has been utilised to predict water and gas pathways around active longwall panels using two case studies. This information has proved invaluable m the design of methane drainage schemes and for risk assessments undertaken at the mining planning stage. The modelling approach described has now been applied successfully to several situations in UK coalmines in order to optimise the position, length and orientation of methane drainage boreholes. The first case study describes the numerical modelling of the stress and shear plane development mund a longwall panel. The simulation was used to predict potential gas pathways through regions of low stress confinrment which are conducive to fluid flow. The conclusions from the modelling were utilised to allow an increase in the volumes of gas drainage and allow the efficient mining of the panel. A detailed discussion is provided on the model construction, determination of input paramters and optimisation of the borehole positions Details are provided on how the models allow a prediction of the fracture patterns, stress distributions and zones of reduced permeability around an active longwall panel. The second case study describes the numerical modelling of a fault adjacent to a face line drivage of a panel that had just started to be retreated. An inrush of water had occurred and a concern was whether further mining would lead to more extensive inrushes or whether the water inrush was associated with more local, limited capacity water bearing features. The role of a fault that was positioned close to the locality of the mine workings was examined. Fracture patterns stresses, strata permeability and water flows were predicted using mechanical and hydro-mechanical coupled models.

Jan 1, 2003

Case study data were analyzed to develop and quantify empirical stress transfer relationships between seams for both longwall and room and pillar mines. Layering in the innerburden and the distance between seams were determined to be the controlling factors. To evaluate the effect of bedding planes on stress transfer, laboratory studies were conducted using layered, low modulus gravity loaded photoelastic models. Parameters investigated were thickness, number of discrete layers, modulus and friction between layers. Results showed that there was significant distortion of the pressure bulb in highly laminated conditions which correlated with the results of empirical analysis. Relationships developed were used to modify the results obtained from numerical modelling between multi-seam longwall operations. Research conclusions were demonstrated using case studies.

Jan 1, 1995

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By Syd S. Peng

Full-face shield leg pressures in a longwall panel for a three-month period were collected and analyzed. The pressure data were presented in the following forms: full- panel full-face shield pressure, individual shield pressure, full-face shield pressure, full-panel time-weighted-average pressure, and relationships among setting pressure, final pressure and pressure increment. Although shield pressure varies from shield to shield and from cycle to cycle, the setting pressure and face advance rate do control the 6nal pressure and time-weighted average pressure.

Jan 1, 1997

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

During the last decade mechanical rock excavation has become increasingly widespread in the mining industry and, more in general, in excavation engineering. This technology, especially the tools and their operating mode, has developed according to empirical procedures and for this reason their validity should be ascertained by systematically re-examining the rock breakage processes. This topic has been approached in the framework of a joint research project involving the Universities of Cagliari (Italy) and Wollongong (Australia). The investigation has been carried out experimentally as well as with the methods of numerical modelling which is based on fracture mechanics principles. The first results of this integrated research led to the proposal of an interpretation of rock breakage by means of drag tools and to the identification of a basic correlation between the rake angle of the tool and the grain size of the rock fragments produced and, therefore, the energy efficiency of the operation.

Jan 1, 1990

By Khaled Morsy

This study presents a typical stress-strain model for coal material using the available in-situ and laboratory tests data conducted on coal. This model can be used as a basic coal model in finite element applications The effects of pillar width-to-height ratio and the confining pressure have been considered in this model. The extended Drucker-Prager model with mobilized friction angle was found to be very successful in simulating the proposed model.

Jan 1, 2001

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By Winton J. Gale

The design of the reinforcement systems required to stabilise mine roadways has developed through the application of field measurement techniques. These techniques have allowed the level of security of a given opening to be determined from an assessment of the loading within the reinforcement, the extent of roof deformation and experience. The design systems developed are now used extensively in a wide variety of geological environment. Recent interpretative techniques have been developed to improve the level of confidence when designing roadway reinforcement. The techniques are particularly applicable for roadways subject to either weak materials or extreme stress levels. A second area of application is where roadway advance rates and hence the timing of reinforcement placement are critical. The newly developed techniques include both analytical and computational models. The validated computational techniques allow a more rational approach to investigation of the effect of varying reinforcement type, timing of placement and density on the level of stability achieved.

Jan 1, 1992

By Zhanjing Yu

In this paper, an equation is developed to characterize the relationship between the UBC and plate size using a boundary integral approach. The equation was validated by the results from mo& than seventy (70) plate loading tests of different sizes conducted in various underground coal mines throughout the Illinois Coal Basin. The equation indicates that the UBC decreases as the plate size increases. The fundamental solution for this boundary integral problems is the Boussinesq equation. The load exerted by the plate on the floor surface is assumed to be uniformly distributed. Both normal and tangential loads are considered. It is also assumed that the floor fails in shear in a plate loading test. The equation may provide the mine operators with a useful tool to obtain from a plate load test of any plate size the UBC value required by the regulations.

Jan 1, 1993

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Thomas M. Barczak

A theoretical evaluation of the impact of horizontal load on shield support capacity is made from a static rigid body analysis of the shield structure. Parameters affecting horizontal support resistance are investigated for a typical too-leg shield design. Horizontal forces acting on a roof support element are found to be both roof-generated and shield-generated. The impact of shield-generated horizontal forces on roof strata is also discussed from a theoretical viewpoint in relation to desired ground control. A technique is described whereby horizontal loading of shield supports can be measured underground. Horizontal load measurements from two different longwall faces were found to be significant, ranging from 20-35 pct of measured vertical load.

Jan 1, 1984

By B. T. Wells

This work concerns the stress fields encountered around mining tunnels. A critical review is undertaken of the various analytical assessments of the support requirements for mining tunnels. Comments are made regarding degree and type of support together with method and timing of installation. The results have been used to indicate the type of support required in different mining and geological conditions.

Jan 1, 1981

By Bruce Hebblewhite

An ACARP-funded industry research project in Australia recently investigated the problem of premature rock bolt failures in underground coal mines. The project carried out limited sampling from 9 different collieries in NSW and Queensland, followed by a more comprehensive, controlled sampling from one colliery. Over 50 broken bolts were collected and subjected to metallurgical analysis at UNSW to determine both the steel composition and to analyse the fracture surfaces. Prior to this study, there had been anecdotal evidence of similar bolt failures from a number of sites within the industry. The sampling and analysis conducted by this project - whilst being below a statistically representative sample of the entire industry bolt population - highlighted the fact that bolt failures were continuing to occur at a number of sites, in both older and recently installed bolts. The failures were almost entirely attributable to stress corrosion cracking (SCC). It appears that a combination of factors - including steel composition, bolt manufacturing process, loading environment, geological and hydrological environment, bacterial corrosion - can all contribute to this problem. There is no simple solution, however, as with similar research findings from the UK, it appears that steels with higher values of fracture toughness, or Charpy Index, are less susceptible to SCC. Testing to date has been limited to bolt failures below the resin encapsulation horizon. A real concern is the potential extent of the problem at higher horizons, within the encapsulation. These may require some form of non-destructive testing (NDT) for detection. Initial trials in Australia of the ultrasonic device developed by DMT in Germany have proved encouraging. Further testing using this device is anticipated in future research. This paper describes the outcomes of the project, completed in 2002.

Jan 1, 2003