Search Documents

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By P. Tapp, T. Evans, N. A. Molloy, J. Lucas

"Consideration of the protoype tuyere geometry for injection of inert gas through the bottom in a basic oxygen steel furnace and a requirement to specify an optimal flow for bottom wear and metal penetration led to experimental investigations[l,2] to apply the results of previous workers to this specific case, Flow velocity profile development within the tuyere was proposed as significant and the experimental scheme was designed to test this. It is proposed that the design criterion for the conditions of optimal flow of the prototype geometry be based on the non-dimensional mass velocity.INTRODUCTIONSharma[3] tested small diameter tuyeres in a laboratory hot model using molten iron to define a flow criterion for prevention of penetration of the bath liquid into the tuyere. Using argon, nitrogen and helium through a range of tuyeres (1 to 3 mm ill ) he proposed the jet Froude number C Fr' ) with the critical value being 2400 - 2500 or higher. Sonic or supersonic velocity was not a sufficient criterion. The tuyere design was a parallel tubular duct of moderate aspect ratio CAR) i.e. the ratio of length to diameter ranging from about 22 to 36 in the experimental furnace.Farmer et al[4] stated their their aim ""to develop a unifying explanation and procedure for the proper design of tuyeres"" but disagreed with Sharma's jet Froude number criterion. Recalculating Sharma's data they proposed instead a fully expanded Mach number of 1.75 with an initial expansion angle of ten degrees as the lower bounds of flow to meet the design requirement. They experimented with tuyeres in a water model using tubular, annular and convergent-divergent nozzles. The aspect ratio of the parallel duct tuyeres was from 533 to 762 using diameters of 1.4, 1.7 and 2.0 mm C the diameters being of tubes to be used full scale). Subsequently these results were applied to a prototype tuyere using a diameter of 1.7 mm with beneficial results in practice. This tuyere had an aspect ratio of 1067."

Jan 1, 1996

By Yanxia Lu

Porous silicon carbide (SiC) has been the top selection for diesel particular filters (DPFs) since 2000 because of its high thermal diffusivity and strong body, which help it to survive in the harsh environment of a diesel exhaust system. However, the process to produce SiC DPFs is a costly one. The work presented herein describes more cost effective composite materials for this application, namely Si-SiC and Si₃N₄-SiC. Both composites have shown excellent filtration efficiency, low back pressure and outstanding survivability of regeneration at high soot loadings. Since the composites are batched from silicon metal, they can be prepared by a low temperature process that is impossible in the production of pure SiC PDFs. In fact, fabrication of SiC composites simply involves reactions between nitrogen gas and silicon metal, or silicon metal bonded with SiC, and as such uses a much less costly process when compared to the one employed to make SiC. In addition, the pore structure of the composites can easily be tuned by selecting raw materials and changing the ratio of two components. A typical pore structure consists of well connected pores with a median pore size of 5-20 µm and a porosity of 40-55%. This talk will describe the exothermic behavior as well as the mechanical and thermal properties of SiC composites in comparison to those of SiC filters. It will also show the superior thermal shock resistance of Si₃N₄ bonded SiC which is due to the unique combination of these phases that lowers the thermal expansion and elastic modulus relative to pure SiC.

Jan 1, 2006

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi-industrial scale experimental system. Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/cm3 has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/cm3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition of the car engine.

Jan 1, 2003

By Jürgen Antrekowitsch

Typical zinc oxides recovered from wastes like steel mill dusts and neutral leaching residues are of a low quality because of impurities like fluorine, chlorine, lead and others. Therefore, they are not comparable to technical grade zinc oxides produced in “French” or “American Process”. Some new developments, most of them still in pilot scale, try to establish processes where higher qualities of the product should be achieved. Zinc oxides are not only supposed to be an input material for electrolytic zinc production. Far more, they should find their way into the zinc oxide market as a substitute for technical grade zinc oxides. Furthermore, a new field of application for these oxides has been investigated at the department of Nonferrous Metallurgy, University of Leoben. Because of a higher acceptance concerning different impurities in relation to zinc winning electrolyses, a use in electrolytic galvanizing shows an interesting option. Therefore, synthetic zinc oxides with different impurities were generated to study the effect of these impurities especially on the quality of the zinc layer. Typical steel sheets, as used for car bodies, were electrolytically galvanized and the resulting layer was analysed, as main impurities compounds of fluorine, chlorine, iron, lead and calcium were used for the investigations. Beside the layer quality, the current efficiency and the possible galvanizing speed were examined. The results give an indication, weather such an alternative application can be feasible from a technical and economical point of view or not. 597

Jan 1, 2008

By Lan Li, Izaak Williamson

"The efficient separation and storage of CO2 from power plant flue gases can reduce the amount of CO2 released into the atmosphere and mitigate global warming. Potential candidates for industrial applications are solid sorbent materials. Crucial factors to control the efficiency of porous sorbent materials include the framework and pore structure, and the chemical and physical reactivity of CO2 within the pores. Computational modeling approaches, based on density functional theory (DFT) and van der Waals-DFT, have been applied to nanoporous solid – manganese dioxide a-MnO2. We found that the types and charges of cations as dopants in the a-MnO2 and the concentration of CO2 influence the structural features of a-MnO2, which control its CO2 selectivity performance within the flue gases.IntroductionCarbon capture and storage is a technique to separate large quantities of CO2 from power plant flue gases before being released into the atmosphere. Porous solids are a potential candidate as sorbents to “trap” CO2 through chemical or physical adsorption on their porous surfaces[1]. Such separation efficiency is determined by the size and shape of its pores and by the interaction between the porous surface and the gas adsorbates. The incorporation of cations into the pore can act as a means of structural support and alter the pore diameter to be comparable to the kinetic diameter of the gas adsorbate, such as CO2.A porous solid of particular interest for CCS is manganese dioxide a-MnO2, an octahedral molecular sieve (OMS) composed of edge-sharing MnO6 octahedra that are linked into a nanoporous framework[2]. The framework consists of (1×1) and (2×2) tunnels, referred to as OMS-2. Due to the larger tunnel size, cations and gas adsorbates prefer to reside along the (2×2) tunnel axis of the OMS-2. As seen in Figure 1, a potassium cation K+ is located in the (2×2) tunnel, known as cryptomelane-type MnO2. Its pore diameter of ~ 4.6 Å gives it a good CO2 selectivity performance, because the diameter is comparable to the kinetic diameter of 3.3 Å for CO2[3]. Alternatively, replacing potassium K+ with other cations, e.g. barium Ba2+, sodium Na+ or lithium Li+, in the OMS-2 tunnel is of great research interest, due to the effects of their concentrations, types and charges on the CO2 selectivity efficiency and sorption hysteresis phenomenon[2,4]."

Jan 1, 2014

By Stephan Mulch, Christian His, Patrick M. Stephan, Thibault Champion

"When fuel costs increase dramatically, waste to energy (WTE) conversion technologies become a good alternative to produce energy. The potential energy available in domestic wastes, in developed countries, could be upwards of 4% of their total energy needs. Due to low energy recovery and low level of treated domestic wastes in many countries, the energy coming from waste is generally less than 0.5% of the country needs.Domestic waste incineration can convert heat to electricity for industry and housing and allow waste volume reduction in countries where land fills are a scarce resource.There is a request to improve existing combustion technology by increasing energy recovery with better heat transfer in the boiler and also by increasing lining durability with more resistant materials and technologies.The knowledge of corrosion phenomena and material performance allows Saint-Gobain Group to develop and propose high performance refractory lining solutions.IntroductionThe interest in alternative energy has been growing dramatically in the two last decades due to several combined factors, such as global energy demand, fuels prices evolution (e.g. crude oil, Figure 1) or environmental and geopolitics factors"

Jan 1, 2008

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By Vânia L. L. Andrade

Igarapé Bahia Mine is located in Carajás area, northern Brazil. Currently Companhia Vale do Rio Doce operates there a CIP / heap leaching plant treating an oxide gold ore containing about 4 g Au /t and 0,2% Cu, which produces 11 t of gold per year. Recent geological survey has identified a signifcant copper-gold reserve underneath the oxide gold ore. The processing aspects of this copper-gold sulphide ore are described in this paper. It includes ore characterization studies, grinding and flotation tests, orebody variability assessment, flowsheet selection and preliminary economical evaluation Emphasis is given to studies aimed at depressing fluorine bearing minerals to achieve a clean and marketable flotation concentrate.

Jan 1, 1999

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By Jack Thibodeau

During the past six years, most states have promulgated water quality regulations which contain numerical aquatic life standards for heavy metals. In addition, the Environmental Protection Agency (EPA) promulgated national water quality standards in 1992 which also include numerical aquatic life criteria for heavy metals. Numerous wastewater discharge permits have been issued by the states and EPA to industrial facilities which include low microgram per liter heavy metal limitations. In many instances, the limitations are below detection limits or treatability limits using state-of-the-art analytical methods or treatment technologies. This paper will discuss options for conducting studies, including the use of water-effect ratios, metal partitioning coefficients, and recalculation procedures to develop site-specific metals criteria and higher permit limitations. The installation of expensive metal treatment systems to remove trace metals may be avoided if higher permit limits are indicated by the site-specific studies.

Jan 1, 1996

By N. A. Vatolin, L. I. Leontjev, S. V. Shavrin

The ever growing interest to the complex iron ores may be attributed to possible production of the naturally alloyed metals and the efficient recovery of the associated elements. However, the conventional technique for complex ore processing is complicated and in some cases even impossible. A pyrometallurgical benefiation of such ores without melted slag formation has been advanced. A version of the technique assumes pellet production with metal coagulated within a slag shell on grinding the pellets, the metal phase is mechanically separated from the slag shell. The technique has been run up with ferro chromo nickel, high-titanium, high-magnesia, alumina phosphorus ores and concentrates. Another version of the pyrometallurgical benefication without melted slag formation in a rotary kiln has been developed from the schemes for processing red mud of alumina manufacture and high-titanium concentrates. Means have been put up to improve schemes available for lex iron ore processing with primary emphasis on material pretreatment before blast furnace and steelmaking processes. Vanadium-bearing titanomagnetite conentrate oxidized pellets possess low strength at reduction. The technique suggested for pelletizing in the controlled atmosphere improves the afore said pellet metallurgical properties. Prodution of metallized pellets in a conveyor roasting machine holds considerable promise for blast furnace and steelmaking processes. In processing the high-sulphur iron ores still another technique is proposed to roast the fluxed pellets with 95% and more desulphuration.

Jan 1, 1988

By P. A. Manohar

This paper describes an implementation of the Potts model for simulation of grain growth in 2D on a distributed-memory parallel architecture. The simulation scheme utilizes a continuous-time, asynchronous parallel version of the n-fold way algorithm. Each Processing Element (PE) carries a piece of the global simulation domain while the virtual topology of the PEs is in the form of a square grid in 2D and Torus in 3D. Different PEs have different local simulated times. Inter-processor communication is carried by the Message Passing Interface (MPI) routines. Sample results for grain growth simulation in 2D are presented for a 840 x 840 global domain size distributed over 16 PEs. The grain growth kinetics obtained in the simulation of pure, isotropic systems is in good agreement with the theory. Grain size distributions obtained in the parallel simulation are well described by the lognormal distribution, thus validating the simulation procedure. Keywords: Metropolis algorithm. n-fold way algorithm, asynchronous parallelization, grain growth

Jan 1, 2003

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Zhanjun Wang, Yongqi Sun, Mei Zhang, Zuotai Zhang, Min Guo

The role of fluorine on the viscous and crystallization behavior of CaO-SiO2-MgO-Al2O3-FetO-P2O5-(CaF2) slags were explored using the rotating cylinder method, non-isothermal differential scanning calorimeter (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. It was found that the viscosity slightly decreased with increasing CaF2 content. It was also found that CaF2 addition can promote the primary phase transformed from MgFe2O4 spinel to Ca3(PO4)F, which was beneficial to the enrichment of phosphorus. Additionally, the structure of the slags explained by X-ray photoelectron spectroscopy (XPS) and magic angular spinning nuclear magnetic resonance (MAS-NMR) were further analyzed, which was well in accordance with the above analysis.

Jan 1, 2016

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002