Search Documents

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By Peter Fischer

A demonstration plant for QSL technology with a continuous through-put of up to 10 t/h concentrate has been in operation at the Berzelius smelter, Duisburg, Germany since early 1981. In the QSL-process, both oxidation and reduction steps are performed in a single horizontal long cylindrical reactor. In the present demo-reacior, 2.5 M diameter by 22 M long, these steps are separated by a low partition wall with an underflow opening, to prevent backmixing of slag. -Tests on a variety of concentrates, including high-lead Missouri-type material and lower grades, have shown recoveries and consumables indicating very attractive economics. Investment cost estimates further enhance the economic attractiveness. Environmental protection afforded by the QSL system is a major advantage. The process has proven its reliability and versatility and is now ready for commercialization. Continued test work, including smelting secondary lead materials, is planned.

Jan 1, 1983

By James D. Navratil

Neutral bifunctional organophosphorus solvent extractants (such as carbamoylmethylphosphonates and carbamoylmethylphosphine oxides) strongly extract lanthanides and actinides and do not extract more than 40 other elements from mineral acids. Because of their excellent properties they have been found useful for F-element recovery and purification processes. A brief overview of the lanthanide and actinide extraction chemistry of these reagents will be given.

Jan 1, 1990

By A. G. Jackson, Rand R. Biggers, John D. Busbee, Iman Maartense, David P. Lubbers, David C. Liptak

"This paper describes the application of Raman Spectroscopy for characterizing superconducting YBCO thin film parameters. Attenuation of the substrate Raman spectrum as a function of material deposited is established. Also a correlation between film quality and Raman spectrum is explored. The identification and discrimination of superconducting and non-superconducting phases of YBCO is presented. The critical temperature (Tc) of a film as a function of its oxygen content is also established using Raman peak ratios. These results provide significant implications toward the use of Raman Spectroscopy for in situ monitoring and control of the PLD process. Film quality can be controlled via optimization of film oxygen content and reduction of improper YBCO phases. Film thickness can be controlled by monitoring the response of the substrate material. Also the PLD process can be studied and modeled using this powerful observation tool.IntroductionSuperconductors are materials that possess unique characteristics when cooled to sufficiently low temperatures. Below a material's critical temperature (Tc) it exhibits zero resistance to current flow. One such material, yttrium barium copper oxide (YBCO) has a critical temperature of approximately 92° K. Due to its high critical temperature YBCO is being aggressively researched for many possible applications, because of high current carrying capability and strong pinning of flux lines.YBCO in the 123 form is a ceramic material that was discovered in February, 1987. Its unit cell structure is shown in Figure 1 [ 1,2]."

Jan 1, 1997

By K. C. Mills, P. N. Quested, A. P. Day, R. F. Brooks

"Methods have been developed to measure the physical properties of molten materials relevant to the fluid flow in high temperature processes. Data for the densities, viscosities and surface tensions of Al-, Ni- and Fe-based alloys are compared with (i) values for the pure metals and (ii) estimated values obtained from models making use of chemical composition of the alloy. Experimental values for metallurgical slags are also given and compared with estimated values.1 IntroductionPhysical property data has proved very useful in improving process control and product quality. For instance, in the continuous casting of steel the viscosity (TJ) of the mould flux is important since it determines (i) the optimum casting conditions, nVc = 2.5±1 dPas (m min-1) where V c is the casting speed and (ii) the level of slag entrapment (which leads to inclusions) in the metal. Thus data for properties like viscosity are exceedingly useful in understanding the process and the problems encountered and the causes of defects and problems.Another interesting development which has helped to increase our knowledge of processes and improve process control and product quality is the development of mathematical models of the fluid and heat flow in the process. These models have been developed to the stage where one of the prime requirements is for good physical property data for the industrial materials involved. Recently, Oxley [1] has shown that the use of reliable, experimental, property values for the commercial alloy in a commercial software package produced a significant improvement in the prediction of casting defects. Thus reliable property data are required for liquid metals but also for (i) liquid slags since many processes involve the use of a slag to refine and protect the metal or to lubricate the mould and (ii) refractories, sand and investment moulds."

Jan 1, 1999

By Guo Chen, Jin Chen, Jinhui Peng

In this paper, solving common problem of electrostatic precipitator (ESP), which was frequently ruptured of the cathode insulation in the production process were studied. The microwave heating airflow technology was introduced, which takes full advantage of its unique properties, solves the output problem of the high temperature air, achieves purpose of energy conservation, important economic significance and environmental significance. The mathematical models and designing of microwave high-temperature hot air system was calculated. The common forms of heat exchangers and comparative analysis were also introduced. The conditions found to be at the temperature of 240 °C. Under optimum conditions, the microwave heating power was 1482 W. Based on the mention results, this microwave heating method can be applied effectively and efficiently way for the production process of electrostatic precipitator.

Jan 1, 2015

By J. J. Rush

Neutron scattering and analysis techniques are extremely powerful, often unique, probes for the characterization of the amount, location, bonding states, and dynamics of hydrogen in all classes of materials. Developments over the past decade at the NIST Center for Neutron Research and elsewhere have greatly increased the sensitivity and dynamic range of neutron methods. In this paper, we provide a flavor of the capabilities of modem neutron instrumentation for the study of hydrogen in a number of technologically interesting systems, including metal hydrides, fuel-cell materials, fullerenes, and disordered carbons.

Jan 1, 2002

By Cailing Zhen, Jian Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Guixiang Huang

The grate-kiln process has been widely applied for oxide pellet production with the quick development of steel industry in China, but ring formation takes place which adversely affects the productivity and properties of fired pellets. Rotary kiln at high temperature seems a black box, and ring formation is difficult to measure directly by current technology. It’s of great importance to monitor ring formation during firing of pellets. Therefore, a method for estimating the thickness of ring formation in rotary kilns was studied, based on working out theoretically the relationship between ring thickness and the outside surface of the kiln, according to steady-state heat transfer across a cylinder, which provides a soft-sensing technique for ring formation at high temperature, and achieves stable pellet production .

Jan 1, 2015

By Renaud Metz

The DOPA process (Direct Oxidation of a Precursor Alloy) was used to prepare ceramic powders based on doped SnO2 and ZnO. The DOPA process consists essentially in the direct oxidation of a homogeneous precursor alloy. A unique advantage of this process is its rather benign environmental impact since no dangerous reactants are used and no harmful by-products are generated. Only oxygen and the alloy metals participate on the chemical reaction to produce the multi-component oxide. Homogeneous alloys of niobium, cobalt and chromium doped tin have been prepared. The molten metal alloy is atomised in air using a double fluid nozzle to produce metallic powders. A subsequent thermal treatment is carried out to fully oxidise the sprayed metal alloy powders. These raw powders are used to prepare a ceramic powder through a mill homogenisation and atomisation process. The ceramic powder is then uniaxially compacted in disc shape and sintered in an oxidising atmosphere. The resulting sintered bodies are metallised on their flat faces and the cylindrical surface is passivated using lead free glass enamel. These ceramics present excellent semiconducting properties with non-linear (non-ohmic) characteristics. The DOPA process is found to be an attractive procedure to obtain ceramic powders for the preparation of SnO2 varistors.

Jan 1, 2006

The kinetics of the oxidation of cyanide by manganese dioxide was studied using a rotation disc electrode system. The rate? of the half-cell reaction of cyanide oxidation is increased at higher hydroxide concentrations. An addition of copper up to 0.001 mole/l was found to enhance the diffusion current, especially at a high hydroxide concentration (0. 1M). A similar enhancement of the reaction rate is also achieved with nickel added at levels up to 0.01 mole/l. Manganese dioxide however requires a i:ow pH to achieve reasonable reduction rates. Leaching studies indicated that the initial reaction rate is strongly dependent on pH, initial concentration of cyanide. Using manganese dioxide cyanide could be oxidized at neutral pH's and ambient temperatures.

Jan 1, 1989

By Gavin Beer

The Chelopech Copper/Gold Mine, located in west-central Bulgaria, has been in operation since 1953 producing a low-grade copper/gold concentrate containing up to six percent arsenic by weight. The penalties and restrictions imposed on smelting this concentrate, have seen the past operators of the mine strive to find a balance between achieving acceptable metal returns from the smelters and installing novel or unproven technologies in the face of changing political and economic climates. This paper documents the colourful history of the concentrate processing alternatives that have been investigated and implemented over the 45 year life of the Chelopech Mine, culminating in the high pressure oxidation option that is now the focus of a Definitive Feasibility Study (DFS) presently being undertaken by GRD Minproc Limited. The fundamental chemistry of the preceding alternatives is outlined followed by a discussion as to why each was ultimately not employed. A detailed description of the technology proposed in the DFS is given including: pressure oxidation, arsenic fixation, SX/EW copper recovery, CIL gold recovery and AVR/SART cyanide/copper recovery processes. Keywords: Arsenic, Scorodite, HPOX, Chelopech, Dundee

Jan 1, 2005

By Tom McCullough

The purpose of this paper is to discuss the implementation and results derived from installing oxy-fuel burners in a l80 ton copper reverbatory melting furnace. Specific results will be discussed in the areas of melt chemistry, furnace modifications, productivity, process enhancements, and the combustion system capabilities.

Jan 1, 1996

By Songlin Zhang

"The McCoy/Cove mine, located in Eureka-Battle Mountain trend of Nevada, is a gold and silver deposit. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and volume variance correction. The grade tonnage distributions of recoverable reserves were constructed and compared with the distributions defined by blast hole assays. Optimal pits were generated by Whittle 4D pit optimization package to analyze the impact of different processing recoveries at different economic cutoffs. The results were compared with ordinary kriging. The study indicates that the proposed method for multi-mineral recoverable reserve estimation is more accurate than kriging in tenns of grade and tonnage. The method of using recoverable reserves for pit optimization will maximize global reserve recovery and revenue, and is more efficient than condition simulation regarding computing power.ABSTRACT ONLY"

Jan 1, 1997

By Hideyuki Takahashi, Taro Aichi, Kazuyuki Tohji, Makoto Muramatsu, Rie Sato

"There are several ways to condition lead-based alloy anodes for zinc electrowinning: electrochemical treatment, chemical treatment and physical treatment. Two advantages of physical treatments are their productivity and variety. In this report, physical treatments, including blasting with silica, alumina, steel grit and cut zinc wire, were tested. The laboratory tests confirmed there were differences in the formation of anode scales during electrowinning and in the suppression of lead dissolution from the anodes. With an increase in the surface roughness, the misfit between the PbC""2 and the MnC>2 was mitigated and the anchor effect was promoted; these effects resulted in dense Mn oxide scales on the anode.IntroductionZinc is widely used for hot-dip zinc plating and for die casting alloys. As a supplier of materials, we have endeavored to produce zinc that is economical and contains as little impurity as possible. As a result of our efforts, a technology for consistently providing special high-grade (SHG) zinc has been established. However, as seen in the issuance of the Restriction of Hazardous Substances (RoHS) Directive, public awareness of the industrial impact of heavy metals on the environment has been heightened. Increasing efforts to control environmentally sensitive substances will be necessary for our production processes.Electrolytic SHG zinc is produced by electrodeposition in an acidic solution with a Pb-Ag or Pb-Ag-Ca alloy for the anode and an Al alloy for the cathode. Pb alloy anodes are widely used because of their excellent durability; however, they are a source of Pb, which is the main impurity of the product."

Jan 1, 2012

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By Shun Fujieda, Shigeru Suzuki, Kozo Shinoda, Tetsuo Fujita

"Dowa's scorodite, synthesized by oxidation of Fe(II) ions in the presence of As(V) ions at atmospheric pressure, was characterized. The scorodite was well crystallized and had a very low solubility. To examine the conditions for stable storage of the scorodite for long periods, experiments with various synthesis and leaching conditions were done. The scorodite had a very low arsenic solubility in sea water. It was estimated in consecutive leaching tests that the arsenic concentration would eventually converge to zero. The prevention of arsenic leaching by adding goethite or ferrihydrite was limited in some cases. Very low toxicity was confirmed by toxicity tests. The investigation results suggest that disposal at a specifically designed well-controlled storage place is preferable for the scorodite whose toxicity had been made sufficiently low. Disposal to an isolated final disposal site with more stringent prevention for the outflow of toxic substances was thought another option.IntroductionArsenic is a considerable environmental concern. A system of technologies for the effective immobilization, storage and final disposal has been sought. Dowa Metals & Mining Co. Ltd. has developed a unique scorodite synthesis method (DMSP®) which works at ambient pressure [1]. The scorodite is precipitated by oxidizing Fe(II) ions in a high-concentration As(V) solution. The scorodite produced in this way does not readily release arsenic because of its high crystallinity. Final disposal is necessary because scorodite currently has no commercial value. A standard method for the final disposal of scorodite has not been established because its long-term stability under various conditions has not been fully examined."

Jan 1, 2012

By Xuyang Liu, Xuewei Lv, Chenguang Bai, Meilong Hu

"The electro-deoxidation process for ilmenite concentrate in molten salt was studied by cyclic voltammetry and AC impedance spectroscopy. The results from cyclic voltammetry are consistent with those of AC impedance spectroscopy. The results showed that the electro-deoxidation process for ilmenite concentrate consists of two steps. In the first step, Fe is reduced from the ilmenite concentrate. The second reaction is the decomposition of TiCh. CaTiCh is an intermediate product. At low voltage, the electrochemical reaction is the main step. With the increasing potential, the diffusion of ion is the main rate controlling step for the electro-deoxidation of FeTiO3.IntroductionTitania and titanium-rich products are mainly prepared from ilmenite concentrates (FeTi03), which contain about 40%-60% T1O2 after ore dressing and other physical or chemical processes [1]. At present, the main methods to prepare titania are the sulfuric acid process and the chloride process, but the sulfuric acid process consumes a large amount of sulfuric acid and the materials requirements for the chloride process are strict [2], Since the Electro-Deoxidization in Molten Salt (FFC) method was put forward in 2000, many researchers have successfully extracted the metal and alloys by this method, such as Ti, Cr, Tb, Si, Al-Si, TiV, FeTi, etc. [3-7], FeTi alloy is a typical hydrogen storage material, and because of its favorable properties, the preparation of FeTi alloy has become a hot research topic [7-9]. However, the mechanism of electro-deoxidization has not been studied thoroughly [10-11]. Therefore, in this study, the electro-deoxidation process for titanium concentrate was investigated by electrochemical methods, and the study makes a contribution to improving the current efficiency of the electrolysis."

Jan 1, 2012

By Cashman R. S. Mason

Removal of halides (fluoride, chloride) from metallurgical solutions can reduce corrosion rates and improve hygiene from decreased anodic chlorine evolution. This is particularly true for zinc sulphate electrowinning solutions. This paper describes the chemistry of a new process for the removal of halides from such solutions by solvent extraction ? the Teck Cominco Halogon? process, for which patents are pending. In this process, the halides are loaded directly from commercial zinc sulphate solutions and are stripped into a form suitable for disposal. Sulphate extraction efficiency is variable while maintaining halide extraction efficiency. The method of optimizing the solvent composition is demonstrated.

Jan 1, 2003

By Pinakin Chaubal

The campaign life of a modern blast furnace depends on hearth wear. Distributions of liquid iron flow and refractory temperatures have a significant influence on hearth wear. A 3-D comprehensive CFD model has been developed specifically for simulating the blast furnace hearth. It includes both the hot metal flow and conjugate heat transfer thorough the refractories. The model has been extensively validated using measurement data from actual blast furnaces. Good agreements between measured and calculated refractory temperature profiles haven been achieved. It has been used to analyze the velocity and temperature distributions and wear patterns at different furnaces and conditions. The results can be used to point out the directions for protecting the hearth.

Jan 1, 2006

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008