Search Documents

By R. W. Hammack

Results for the treatment of a problematic mining wastewater using bacterial sulfate reduction (BSR) are presented. Specifically, a BSR pilot treatment plant (250 L per day) was used to treat Berkeley Pit simulant to discharge standards with the selective recovery of separate Cu- and Zn-sulfide concentrates. Concentrates recovered in these tests contained greater than 50 % of the target metal and met specifications for sale to existing smelters. The biological component of the treatment was found to be surprisingly robust. Scaling and solid/liquid separation problems were encountered but considered normal for sulfide treatment. For Berkeley Pit water, capital costs for BSR treatment was found to be comparable to high-density sludge lime treatment. The value received from the sale of recovered copper ands zinc concentrates paid for all the operating costs.

Jan 1, 1999

By G. P. Swayn

Recycling of dusts produced in a flash furnace by direct injection provides the opportunity to reduce recycle loads to the reaction shaft, lower fuel requirements and possibly increase metal recovery to products. Ausmelt has provided an Ausmelt lance system for injecting dusts collected from the waste heat boiler and electrostatic precipitator units, directly into the slag melt. This has been installed and operated in the Kalgoorlie Nickel Smelter with systems for feeding dust, for firing with oil and air, and for raising and lowering the lance. Modelling and testwork development of dust injection, results of commercial trials and design considerations for further opportunities of the Ausmelt lance system, are discussed.

Jan 1, 1994

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Guozhu Ye, Eric’ Burstrom

"Despite of numerous solutions for recovery of zinc from EAF dust have been suggested and tested in laboratory scale over the last three decades, Waelz kiln process is still the most dominating process for treatment of EAF dust. Few of the proposed alternative methods have gone beyond the laboratory tests. This paper will give you insights to some of the concepts that have been pilot tested at MEFOS. The innovative aspects of these concepts will be shown and the major results will be highlighted. These include the following concepts: - Production of a crude zinc oxide product with low halide content for zinc electrowinning using a DC furnace with hollow electrode- Production of a bypass filter dust containing more than 50%ZnO by injection of EAF dust to the electric arc furnace during refining combined with a bypass filter system- Elimination of zinc ferrite by CaO treatment for electrowinning with EZINEX process - Selective reduction of iron oxide in zinc ferrite for simultaneous recovery of ZnO andmetallic ironIntroductionRecovery of zinc from EAF dust is dominated by the Waelz process since EAF dust has been classified as hazardous waste by EPA in the early 1980´s. A large number of alternative processes have been suggested and tested without commercial success due to two major reasons [1]:- High content of chlorine and fluorine for the pyrometallurgical alternatives- High content of ZnOFe2O3 for the hydrometallurgical processesMany innovative concepts for treatment of EAF dust for zinc recovery have been pilot tested at MEFOS in the past 20 years. This paper will review some of the concepts focusing on the two problems mentioned above."

Jan 1, 2008

By Munyaradzi Kwatara, Ron Schonewille, Edgar Peek, Juzer Tayabally

"The potential recovery of nickel from a South-American saprolitic laterite ore using the segregation roasting technique was investigated. The ore was heated to temperatures that ranged between 900 and 1 000°C in a rotary kiln. In all the tests, the laterite ore was first mixed with a predetermined amount of calcium chloride and either coal or coke. By varying the temperature, calcium chloride and reductant in the different tests, a preliminary set of optimal conditions was established for the specific laterite ore that was tested. A combination of chemical analysis and electron-probe-micro-analysis (EPMA) were used to determine and evaluate the effectiveness of segregation roasting on the recovery of nickel. The present paper describes the test procedure and the results that were obtained.IntroductionIt is known that laterite ore resources account for an estimated 72% of the world's nickel resources, with sulfide sources accounting for the remaining 28%. Yet sulfide resources account for 58% of the world's primary nickel production while laterite resources account for the remaining 42% [I]. There are numerous reasons for this discrepancy, but the most important one is the mineralogical and compositional complexity that is associated with laterite ore deposits. For example, this complexity currently offers only limited opportunities for upgrading, thereby creating capital intensive whole ore processing facilities. It then follows logically that the identification and application of a low-cost processing option for the treatment of laterites could potentially open up an opportunity for exploiting these vast untapped laterite resources.To this end, a preliminary screening investigation was initiated by Xstrata Process Support to evaluate the potential application of the so-called (nickel) segregation process as a unit operation that could potentially be integrated into a laterite processing flow sheet. Laboratory bench tests were performed on this segregation process and this paper details some of the findings from this preliminary investigation."

Jan 1, 2011

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

Sensor controlled sorting is a promising technique for the upgrading of scrap aluminium alloys. In a universal detection system of Delft University characteristic features are extracted · from the material particles by means of cameras. Examples are size, texture, edge-structure, homogeneity, and colour pattern. Additional sensors are added for higher selectivity: electromagnetic detection, light transmission, spectral reflection and more. Signal processing theory learns that a classification of particles fundamentally improves as the number of independent features increases. At the laboratories of the Delft University a test bench is available for the development of advanced multi-sensor quality control and sorting systems. It is based on a software system for detection, segmentation and classification of particles, which was especially developed for this application. Work is now in progress for high-speed detection and sorting of non-ferrous alloys, including aluminium casting and wrought alloys. A recently developed actuator design enables positive sorting into more than 3 fractions of particles that are randomly orientated on a flat conveyor belt.

Jan 1, 2000

By Shun Fujieda, Shigeru Suzuki, Kozo Shinoda, Tetsuo Fujita

"Dowa Metals & Mining Co. Ltd. has developed and plant-practiced a unique scorodite synthesis technology (DMSP®) for arsenic immobilization by oxidizing Fe(ll) ions in the presence of As(V) ions. Dowa has improved the DMSP® technology and has developed the process extensively for other applications. This paper focuses on the applicability of the DMSP® for various cases of copper smelting, and introduces other technologies for fixing arsenic and recycling gallium from GaAs, simultaneously processing (fixing) arsenic and thallium, and fixing and recovering arsenic from dilute arsenic solutions. The DMSP® was found to be applicable not only for various processes in nonferrous smelting, but also for other applications with a high potential for reducing environmental problems.IntroductionDowa Metals & Mining Co. Ltd. developed a method for synthesizing scorodite at ambient pressure [1], The scorodite is precipitated by oxidizing Fe(II) ion in a high-concentration As(V) solution. The scorodite produced in this way does not readily release arsenic because of its high crystallinity. Dowa built a demonstration plant for this technology at the Kosaka Smelter and established the production of scorodite at 30 t As/month by treating intermediate products from copper smelting as the starting material. The DMSP® was demonstrated to be favorably applicable to copper smelting [2]. We are engaged in further increasing the amount of arsenic fixation by the use of this process. Further improvements in productivity, cost reduction and applicability in various processes have been devised. Dowa has been endeavoring to resolve other problems as well as to improve productivity. We have gained extensive knowledge on arsenic treatment in our endeavors, enabling us to solve problems and improve productivity. This paper introduces the investigations and developments related to DMSP®."

Jan 1, 2012

By A. Robles

The main goal of the present work is to propose a viable alternative for selective arsenic elimination from copper smelter flue dust without the need of a global leaching scheme for all the individual components of the flue dust. Using this alternative, the inherent copper recovery problems are avoided. Arsenic precipitation is also considered for regenerating the solution and completing the process cycle. The experimental results for arsenic extraction and precipitation are satisfactory. Concentration of NaOH used was relatively low. The main reason for succeeding in high arsenic extraction and low NaOH consumption is due to the previous water washing of the flue dust. Water washing dissolves much of the iron and copper that are present in certain percentage as sulphate.

Jan 1, 1999

By Hans Hein

In its early stage of copper solvent extraction development, SX plants were designed in a series configuration and gradually the copper industry reduced staging and trains for keeping capital investments reasonably low. At a later date of its development, series parallel configuration was applied in some copper SX plants, particularly for increasing copper production at low copper tenor in pregnant leach solution. A gap between series and series parallel configuration had been observed for years. Conventional SX plants in series configuration frequently do not have the flexibility for maintaining designed or expected production level, whenever copper concentrations in pregnant leach solutions are getting low, whereas series parallel flow schemes almost require to double SX feed flows for achieving optimum results. A combined SX configuration breaks the gap and its application potentials are explained.

Jan 1, 2003

By A. V. Tarasov, V. M. Paretsky

"Based on theoretical and experimental studies into the specific features of the mechanism, kinetics, aerodynamics and heat transfer parameters of the flame-type oxidation of metal sulfides in a stream of technical-grade oxygen, a three-dimensional deterministic mathematical model of an oxygen-flame smelting furnace has been developed on the basis of the zonal method for computation of heat exchange. The model is presented in the form of equations taking into consideration the radiation component of the selective radiation, the convection component of mass transfer between the space and surface zones, heating of charge particles due to heat conductivity, accretions formation on a multi-layer refractory lining with inserted cooling elements. The adaptation of the model for a full-scale furnace has demonstrated the possibility for its use for computation of main smelting process parameters. Multifactor model investigations were conducted and the results obtained were applied using statistical methods for development of a simplified computational regression model describing the interrelation of the main output parameters: temperatures of flame, lining, slag and off-gas; heat fluxes to the lining; thickness of accretions; heat removed by cooling elements; copper content of matte. On the basis of this model, a block diagram of the algorithm was developed for control of the thermal conditions of the furnace, as well as the control algorithm itself.IntroductionThis paper presents the results of an integrated modeling and development of principles for control of copper smelting process using as an example the oxygen-flame smelting process (KFP) for treatment of sulfide concentrates at the Kovoguty Krompahy copper smelter (Slovakia) with a capacity of 20,000 tpy of copper."

Jan 1, 2001

By Kazutaka Kunii

It is invariably certain that after punching for IC Leadframes, scrap metal were generated. These seraps were re-dissolved and in order to use as raw material for leadframes, it is necessary to remove the Ni plating. In this study a simple method was developed for the removal of Ni plating by surface oxidation of Ni plating. For this purpose a fundamental study was carried out on the oxidation behavior of Ni plating. Results showed that by controlling the oxidation condition, a considerably high rate of Ni could be removed.

Jan 1, 1996

By Joe Milbourne

The potential for treating copper-nickel-cobalt-platinum group metal concentrates by a fully hydrometallurgical route is discussed. Processes specifically developed for treating these feeds and the potential application of the processes developed for the treatment of chalcopyrite copper concentrates are included in the evaluation. Block flowsheets are provided and the technical characteristics of various processes are compared. The current state of development for each process is summarized and probable economic impacts of the technical features are qualitatively assessed. Perceived risks and rewards associated with each technical concept are provided in the conclusions.

Jan 1, 2003

By S. S. Ryu, J. C. Kim, H. Lee, Y. D. Kim, I. H. Moon

"Recently, W-Cu alloy becomes one of the very important candidate materials for heat sink and packaging in the field of microelectronics due to its good thermal properties. The metal injection molding of W-Cu powder can satisfy the requirement for mass production of complex shaped parts in microelectronic devices. In the present study, the application of MIM process to the nanostructured W-Cu powder prepared by mechanical alloying was investigated. The multi-component binder system of 45PW+ l 5BW+ 30PE+ I OSA was proven to be suitable one for the MIM of the W-Cu composite powders by adopting the debinding cycles of multi-stage in N2 and H2 atmospheres. Other process conditions for the MIM of the nanostructured W-Cu composite powder were also studied. The MIM debinding part of W-30wt.%Cu was sintered to the relative density of more than 96% by sintering at 1200 °C for !hour in H2 atmosphere. Such an improvement of sinterability was attributed to the intrinsic homogenous and fine mixing state of W-Cu phases in nanostructured W-Cu composite powders, and also partly to the effect of the activated sintering by the presence of impurity introduced during the extensive milling.IntroductionW-Cu alloys have been widely used for heavy duty electrical contacts and arcing resistance electrode(1-2). Recently there has been a growing interest in this W-Cu alloy because of its superior thermal managing properties and its high micro wave absorption capacity(3). Such W-Cu alloy parts are conventionally fabricated either by the Cu infiltration sintering technique or by hot pressing of W-Cu powder mixtures. However, these conventional PM techniques are hardly applicable for mass production of small size parts with a complicated shape such as the parts required for microelectronic devices. The metal injection molding(MIM) technique is potentially applicable for the mass production of small and complicatedly shaped parts compared with other PIM forming techniques."

Jan 1, 1998

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides (MA) can be incorporated for use as a transmutation fuel. This study involves characterization of precursor powders and pellets to be inserted into the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U80Pu20)O1.98, and two compositions of MA-MOX with oxygen to metal ratios (O/M) of (U75Pu20Am3Np2)O1.98 and (U75Pu20Am3Np2)O1.95. The precursor powders, which consisted of, highly enriched uranium oxide, HEUO2, depleted uranium oxide, DUO2, neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a field emission gun scanning electron microscope (FEG-SEM) for particle morphology, size, and size distribution prior to pellet production.IntroductionThe Global Nuclear Energy Partnership (GNEP) was created in order for “fuel-cycle supplier” nations to provide assured supplies of nuclear fuel to “fuel-cycle customer” nations. The customer nations would utilize the fuel for electricity generation and subsequently return it to the supplier nation after it is spent. This spent fuel would then be reprocessed by the supplier nation in order to recycle the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials would also be strictly controlled through the International Atomic Energy Agency. One of the thrust areas for the GNEP program is the development of these actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3]."

Jan 1, 2008

By A. Kar, J. Mazumder

"Inherent rapid cooling in laser processing often produces novel materials due to nonequilibrium partitioning during solidification. This paper reports theoretical and experimental investigations on in situ alloy formation with extended solid solution.A mathematical model for determining the composition of metastable alloys and the effects of various process parameters on the composition of extended solid solution is presented. To model the nonequilibrium partitioning of solute in concentrated solution, rate equations and conservation of mass equations are used and an expression for nonequilibrium partition coefficients is derived for concentrated solution, which is realistic for laser alloying and cladding. Effect of rapid cooling on solute segregation is presented by deriving an expression for nonequilibrium partition coefficient.Experiments were performed with Ni-AI and Ni-Hf systems to obtain the composition of solute in the extended solid solution produced during laser cladding."

Jan 1, 1988

By Clyde S. Brooks

This paper undertakes to assess what opportunities exist for the economical recovery of non-ferrous metals from spent catalysts. The most promising recovery appears to lie with metals such as Co, Mo, Ni, W, heterogeneous catalysts used on a large scale in petroleum processing. Nickel is a metal with diverse applications on a large scale notably in hydrocarbon steam reforming and in vegetable oil hydrogenation. In addition, several of the precious metals, notably Pt, Pd, and Rh, find extensive use in fossil fuel processing and in automotive and power plant flue gas control. The hydrometallurgical and pyrometallurgical alternatives for processing are identified and discussed, especially with citations to illustrate reduction to commercial practice. Promising directions for adaptation of appropriate, economic separation technologies for recovery of non-ferrous catalytic metals generated in significant amounts for the secondary metal markets are identified. Recycling

Jan 1, 2000

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By Kouichi Nakano

Austenitic stainless steel, which includes nickel for stabilizing austenitic structure, is used for various purposes, for example, for structural material, corrosion-resistant material, biomaterial etc. Nickel is set as one of the rare metals and economizing on nickel as the natural resources is required. On the other hand, nickel is one of the metals that cause metallic allergy frequently. Therefore, high nitrogen stainless steel, where nitrogen stabilizes austenitic structure instead of nickel, has been developed in Japan and some of the foreign countries for the above reason. When high nitrogen stainless steel is fused and bonded, dissolved nitrogen is released to the atmospheric area, and some of the material properties will change. In this study, we bonded high nitrogen stainless steel by stud welding process, which is able to bond at short time, and we evaluate joint performance. We have got some interesting results from the other tests and examinations.

Jan 1, 2016

By Celaletdin Ergun, Ibrahim Erden, Gurbuz Gunes, Thomas J. Webste, Huinan Liu, Abdurrahman Bahadll

"B, Ti, Ag, AI and Cu substituted hydroxyl apatites were synthesized via precipitation method. Then the samples were air-sintered at 1300°C for 2 hrs and characterized with XRD, SEM, FTIR, and cell adhesion behaviors.IntroductionSynthetic hydroxylapatite (HA, Ca10(P04)6(0H)2) has a similar composition and structure to biological apatite. Therefore, it has been safely and extensively used as an implant material for bone substitute. However, synthetic HA has been used for a various applications including medical or non-medical applications, such as matrices for drug release control, bone cements, tooth paste additive, blood purification agent, monolithic implants or coatings on metallic implants, packing media for column chromatography, gas sensors, catalysis and host materials for lasers and luminescent materials, etc. [1-9].The major factors affecting the performance of HA on these applications are crystal morphology, density, porosity, pore size and distribution, chemical composition, and surface structure. As provided by the high flexibility of the apatite structure a great variety of cationic and anionic species can be substituted into HA structure which is specifically considered as an effective method to modify the properties of HA [10,11]."

Jan 1, 2012

By Biserka Lucheva, Tzonio Tzonev

"A unique DC electric arc rotary furnace with capacity 150 kg has been designed and constructed for the recycling of low-quality scrap and aluminum dross. The main constructive feature of this furnace is that the axially positioned graphite electrodes (cathode and anode) are placed 100 mm away from the rotation axis of the furnace. A specific characteristic of the construction is the possibility one of the electrodes (the anode) apart from moving axially (parallel to the furnace axis) to move at 90° outside the working space. High recovery rate of metal aluminum from aluminum dross (92%) was realized in this furnace. This is the reason for construction of industrial DC electric arc furnace.IntroductionThe consumption of aluminum waste has been rising continuously on a world scale, which is a great stimulus for the development of the technology for aluminum recycling.To recover the aluminum in dross, the conventional recycling process uses salt rotary furnaces heated with a fuel or a gas burner. This treatment process produces a secondary dross containing alumina, salts, impurities and a small amount of aluminum. Molten aluminum is tapped from the furnace and the residue is then dumped from the furnace. It has been the practice to dispose the residue in a landfill. Improvement of this technology, known as the oxy-fuel process, uses a gas burner enriched with oxygen to increase the thermal efficiency [1]. Recent studies show that the most efficient aggregate for recycling of aluminum scrap has turned out to be the rotary tilting furnaces, heated by plasma or electric arc, for which the use of flux is not necessary [2,3].Accordingly, there is a substantial need in the industry for an improved process for recovering free aluminium. It is particularly desirable that such process be cost effective and ecologically safe."

Jan 1, 2008