Search Documents

By D. L. Stewart

"Melt loss is usually one of the highest individual cost items in the operation of ah ingot casting facility. While melt loss and the resulting cost for the entire facility is usually well known (at least via standard cost accounting), dross generation and melt loss for individual unit operations within the plant are usually not known. Thus, the financial impact of various practices, alloys and scrap types is not known. Development of an accurate, relatively low-cost technique for measurement of melt loss at commercial scale would aid in understanding melt loss for existing units, as well as evaluation of the melt loss impact of alternate processes.This paper will describe a methodology developed at Alcoa for accurate and inexpensive measurement of melt loss at commercial scale. The methodology has been used to evaluate the impact of scrap type, melting practices, and dross treatment technology on melt loss."

Jan 1, 2000

By Cyro Takano

An alternative use for recycling of waste from bag house of iron ore sinter plant was tested by producing and evaluating" at laboratory scale, the self reducing cold bonded pellets. This waste was characterized and the self-reducing pellets were produced using anthracite coal fines as reductant and Portland cement or hydrated lime/Blast Furnace slag as binder. It was used the molar ratio of Fe2O3/C (fix) equal to 3. Evolution of cold strength with curing time, for different contents of binder, was evaluated. Cold strength of 200N/pellet was obtained, for sinter dust, after 10 days of curing. Suitable hot strength was also presented and no decrepitation and swelling were observed. Good fractional reduction was obtained at 950°C and 1137°C. These results show that this material may be used by the Self-Reducing Processes for hot metal production, as an alternative route for this dust destination.

Jan 1, 1996

By Pascal Gardin

The purpose of the paper is the mathematical modelling of flows inside steel continuous casting mould. For CFD validation of flow oscillation prediction, unsteady calculations with a realizable k- model were performed in a billet caster with rectangular section. Self sustained and regular oscillations were obtained. Calculated flapping frequency is very close to what is mentioned in literature. For slab caster configuration, flow oscillation is influenced both by lower roll, which creates very small frequency oscillation (0.012 Hz for our water model), and upper roll, which creates slightly higher frequency oscillation (0.05 Hz). The two rolls interact and it is possible to detect both frequencies in the nozzle jet region. Numerical results are in good agreement with measurements for fluctuating velocity spectra and provide explanation for interaction of rolls. To improve flow stability inside the mould, it is established that gas injection in the nozzle has a very positive effect.

Jan 1, 2006

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"Environmental protection is becoming over the years an increasingly significant problem of mankind. Up to the last decade the only way to make the domestic waste harmless in Bulgaria was deposition on uncontrolled landfills without undertaking actions for protection of the soils. This also caused pollution to spread into the surface and underground waters and that is why actions are now undertaken for remediation of contaminated soils. This is achieved by developing projects for the closing down of polluted sites. In the present paper some projects for closing down of polluted areas are discussed. The actual conditions are examined and project decisions for preventing the surface waters from penetrating into the waste are presented. In this way the pollution of the soil is stopped and the soils are gradually remediate.IntroductionSoil is the topmost layer of the earth crust. It consists of mineral particles, organic substances, water, air and living organisms and is an extremely complex and changing living environment. Soil is a non-renewable natural resource which is of considerable importance in a number of crucial processes (production of foods, storing, filtrating and turnover of many substances, including water, carbon and nitrogen). It also serves as a basis for human activities, shaping the landscape, ground on which cultural heritage is built, and source of raw materials. These functions of soil must be protected both because of their social and economic significance and from the point of view of environmental protection.The processes of erosion, loss of organic substances, compaction, salination and contamination contribute to the degrading of soils accompanied by a negative impact on human health, natural ecosystems and changes in climate, as well as on the economy. All these make it necessary to protect soils from contamination. Over the last years intensive work started in Bulgaria for the construction of controlled sanitary landfills for rendering municipal solid waste harmless. Pursuant to Bulgarian legislation, in these controlled sanitary landfills measures are undertaken for protecting the soils from contamination through appropriate project decisions – the filtration of the products from the biological decomposition of waste into the adjacent sites (soils) and, therefore, the contamination of the surface and underground waters is prevented. At the same time the purity of air is maintained, human health is protected and conditions are created for including the controlled sanitary landfills into the surrounding landscape."

Jan 1, 2008

By Mark W. Sajewycz

Creating technology, securing patent rights, and managing a patent portfolio are time-sensitive and dynamic activities. Agreements should be in place with technology partners (employees, contractors, joint venture partners), prior to embarking on research and development projects, so as to mitigate future disputes over patent rights. Technology partners should be educated on patent law basics so as to be mindful of patent bar triggering events. Accurate records must be maintained to capture information relevant for preparation and filing of patent application, including subject matter, names of inventors, and invention date. Developed inventions should be evaluated for whether to file for patent protection, delay patenting until technology is further developed, maintain trade secrecy, or effect deliberate public disclosure. Once decision is made to file for patent protection, time is of the essence, and application for patent protection should be filed as soon as possible, as many countries award patents on a "first-to file" basis. Decisions on where to file are made having regard to potential competitive advantages versus cost considerations, and can be delayed by taking advantage of priority rights recognized in patent legislation of most countries. Once patents are granted, competitors must be policed for potential patent infringement, and legal action may be necessary to prevent patent infringement.

Jan 1, 2006

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By Matthias Frommer, Carl-Peter Reipl, Reinhard Flende

"Today there is a growing demand for strip of superior steels with specifically tailored technological properties. Especially strips of high-strength, micro-alloyed steel grades applied to manufacture longitudinally and spiral-welded pipes are a growth market. Tubes are generally required to have high strength and sufficient toughness values and thus favour specific hot strip microstructures. The correlation of chemical analysis, process parameters and mechanical properties with microstructural features is still a challenging task. During the last decades, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) have become useful tools for the characterization of complex microstructures. The EBSD data provides an immense variety of post-processing possibilities, e.g. related to grains, grain boundaries, misorientations or texture. This paper highlights the results of an advanced analysis of microstructures representing industrial produced hot-rolled strips and presents an approach to define and quantify some essential microstructural parameters.IntroductionHigh-strength microalloyed steels have been used for the production of welded pipes for more than 30 years. However, the alloy design of pipeline grades is being continuously modified and the process technology optimized because of the increasing high strength-toughness combination requirement for pipeline steels. Compact strip production (CSP®) technology is an upcoming promising route for the production of high-quality pipeline steel grades [1]."

Jan 1, 2012

By Y. Sako, E. Nomura, K. Muraguchi, K. Shibata

In 1998, Mitsui Mining & Smelting Co., Ltd. (MMS) produced 70,000 tonnes of lead, 231,000 tonnes of zinc and 214,000 tonnes of copper. MESCO, Inc. has been in charge of the automation and mechanization of smelting facilities promoted by MMS as well as the construction of facilities for chemical production and electronics materials plants, by which MESCO has contributed to the development of MMS. Initially, MESCO developed a casting machine for refined lead in the early 1960's, and thereafter, it developed a casting machine for refined zinc, a stripping machine for zinc tankhouses and energy saving facilities. In the field of copper smelting, it has also developed automation and mechanization facilities.

Jan 1, 2000

By M. A. Gerdel

In carboxylate collector flotation of bastnasite from other semisoluble salt type minerals such as barite various modifiers must be added in order to achieve selective flotation. One such modifier is a lignin sulfonate. It may function in part by acting as a sequestrant for metal ions present, preventing autoactivation in the system by metal ions derived from the minerals themselves. It also functions as a depressant for both bastnasite and barite, chemisorbing on both. However, it is shown that the lignin sulfonate functions as a much stronger depressant for barite than for bastnasite. It is suggested that the; strong depressing action on barite is related to a good fit of the sulfonate into the barite structure.

Jan 1, 1989

By Henry Freiser

For the last several years, a systematic investigation of the equilibrium extraction behavior of selective tervalent lanthanides with representative chelating extractions of a variety of chelating agent families has been undertaken for the purpose of learning how to obtain chelating extractants of improved selectivity for separating individual lanthanide ions. The equilibrium extraction data (expressed as log Kex) for each reagent system are linearly related to the reciprocal ionic radius of the tervalent lanthanide ions. The role of adduct formation, steric hindrance, as well as the nature of the bonding atom in the chelate ring, represent some of the factors affecting selectivity arising out of our database of over 200 individual extraction systems, which will be discussed.

Jan 1, 1989

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By Bernard Bonnetot

The potentialities of hydrogen storage using borohydrides are presented and discussed especially in regard to the recoverable hydrogen amount and to the recovery conditions. A rapid analysis of storage possibilities is proposed taking in account the two main ways for hydrogen evolution: the dehydrogenation obtained using thermal decomposition of borohydrides or the hydrolysis of solid or dissolved borohydrides. The recoverable hydrogen is related to the dehydrogenation conditions and the real hydrogen useful percentage is determined for each case of use. The high temperatures required for dehydrogenation, even using catalyzed borohydrides, lead to poor outlooks for this storage technique. The hydrolysis conditions fix the yield of the recovered hydrogen and rule the storage capacity of the dissolved borohydride, the "fuel".

Jan 1, 2006

By C. Camurri

Results from the Metallurgical Department of Universidad de Conception showed that fire-refined copper could be rolled without previous remelting for deoxidation. The goal of this work is to determine the rheology of fire-refined copper from tensile tests at different temperatures and strain rates, and Ford plane compression tests. All that in order to simulate and calculate rolling process variables. For rheology hardness coefficients, n variables between 0.28 at 600°C and 0.46 at ambient temperature are obtained. The sensibility coefficient for strain rate m varies between 0.056 at 600°C and 0.006 at ambient temperature. The activation energy for plastic flow Q in the considered temperature range is 1436 cal/mol.

Jan 1, 1999

By Douglas Robinson

This paper describes technical work done to develop a Spouted Bed Electrode Cell into a commercially viable Electrowinning Cell; (a previous paper has been presented at the ECS meeting in Paris in May of this year, with a more general overview of the cell, [1]). The studies have included hydrodynamic tests to understand the criteria for the circulating flow of metallic beads in the cell, particularly in the region at the entrance to the draft tube, and electrochemical tests to find a suitable diaphragm for extended time electrolysis. Various patent pending features were developed including a double nozzle to allow for automatic stopping and restarting of the bed, an arrowhead shaped draft tube to control the flow of beads into the entrance to the draft tube, a roof-top shaped device to control the flow of beads out of the top of the draft tube, an overflow weir to allow the continuous recovery of beads from the cell, and a family of diaphragm fabrics for extended operation. Prior to the identification of the diaphragm material, short circuits would develop within a few hours. A pilot scale cell was operated for three days, with continuous operator attention, and then for ten days with operator attention only on day shift. The cell is currently advancing to the next stage of development which will involve continuous testing in a commercial copper electrowinning facility.

Jan 1, 2003

By D. C. Cupertino

Oxime based solvent extraction provides the user with a selective concentration process for copper prior to electrowinning. The selectivity required is largely for copper(II) over iron(III) and this is achieved by the preferential formation of the square planar copper-oxime complex in the organic phase. The copper/iron selectivity of oximes can however, be altered by modifiers or other types of oximes and may be enhanced in the presence of certain esters. Whilst the oxime based SX processes is important for operations leaching copper from laterite ores, the high selectivity will also be significant in processing streams arising from other leaching regimes which are currently under development, for example leaching of sulfide mineral ores. This paper presents some initial results using Molecular Modelling techniques to further our understanding of the nature of the copper/iron-oxime complexation processes together with some plant studies undertaken at a number of different mine sites investigating selectivity, and other properties, for some modified reagents. Some studies of the interfacial properties of the these systems are reported to explain in part the practical observations.

Jan 1, 1999

By Bo Björkman

Four different arsenic containing dusts from the Boliden plant, Boliden mineral AB, Sweden have been examined. A kinetic study of the As elimination was performed in a laboratory scale roasting furnace for roasting furnace ESP dust and smelting furnace ESP dust. Characterisation and thermodynamic calculations were carried out to determine the mineralogy, and the stability of compounds in the dusts studied. The characterisation methods used were chemical analysis, X-ray diffraction analysis and microprobe analysis. It was found in the experiments that a high degree of As elimination was obtained for roasting fumace ESP dust and a low degree for smelting fumace ESP dust. Derived kinetic models are given. A prediction of the As-elimation for settling furnace dust and converter ventilation dust is presented.

Jan 1, 1994

By Pieter Steeneklm, Mazi’ Rejaee

"EXECUTIVE SUMMARYThe automotive industry's search for increased fuel efficiency through component weight reduction has driven the growth in consumption of magnesium metal in the form of die cast alloys. This trend, which began in North America and should soon accelerate in Europe, will require enhanced recycling services since each tonne of metal used for die cast parts production produces about 500 kg of scrap.Currently, the European die cast market is plagued by very high tolling prices for scrap recycling due to lack of competition and high transport costs due to the distances between the scrap generator and the recycling facility. This situation clearly increases the cost of magnesium die cast components and reduces magnesium's competitiveness with other materials. The challenge for the magnesium industry in the short term is to provide cost ·effective recycling solutions for the die cast industry. In addition effective recycling, in the medium to long term, is needed for the anticipated large volumes of secondary or used scrap that will become available as the die cast components reach the end of their life cycle. This paper will present The Antheus Integrated Magnesium Project as a Novel approach addressing some of the key recycling related issues facing the magnesium industry, in particular the die casters. The paper outlines the many advantages of an integrated magnesium metal park, in an overall goal of increasing magnesium metal's competitiveness."

Jan 1, 2000

By B. Q. Li, H. C. de Groh, X. Lu

"A fully 3-D, transient finite element model is developed to represent the magnetic damping effects on complex fluid flow, heat transfer and electromagnetic field distributions in a metallic melt. The model development is based on our in-house finite element code for the fluid flow, heat transfer and electromagnetic field calculations. The numerical model is tested against numerical and experimental results for water as reported in literature. Various numerical simulations are carried out for the melt convection and temperature distribution with and without the presence of a transverse magnetic field. Numerical results show that magnetic damping can be effectively applied to stabilize melt flow, reduce turbulence and flow levels in the melt and over a certain threshold value a higher magnetic field resulted in a greater reduction in velocity. Also, for the study of melt flow instability, a long enough running time is needed to ensure the final fluid flow recirculation pattern. Moreover, numerical results suggest that there seems to exist a threshold value of applied magnetic field, above which magnetic damping becomes possible and below which the convection in the melt is actually enhanced.1. INTRODUCTIONThe imposition of a DC magnetic field on a moving, electrically conducting fluid, such as molten metal or semiconductor melt, produces an opposing Lorentz force that results in a reduction of flow velocity in the liquid. This effect has been explored in both the semiconductor and metals industries to control natural convection and/or surface tension induced Marangoni convection as well as thermally induced flow instability during solidification processing of these melts [1-6]. A mathematical model can be of great use in developing both fundamental understanding of the fluid-magnetic field interactions in these magnetically-assisted processing systems and basic guidelines for process design, control and optimization.This paper presents a 3-D mathematical model for magnetically damped fluid flow and heat transfer in a melt cavity, which is useful for interpreting results for unidirectional solidification processes at slow solidification rate, and some preliminary results concerning the magnetic damping effects on the flow instability in the melt. The model development is based on the finite element solution of the Navier-Stokes equations, energy equations and equations for induced electric field. The model is tested against reported results and is then applied to study the fluid flow and thermal distribution in the metallic melt with and without an external magnetic field."

Jan 1, 1999

By Michael L. Sorokin

The metallic nickel production by converting of nickel matte is analysed from the thermodynamic point of view using earlier developed thermodynamic models for sulphide, metal and slag phase. Three-suffix Margules equations are used to calculate thermodynamic properties of melts. Potential diagrams of Ni-FeS-OSiO2 system are calculated for various temperatures and Fe to Ni ratios. The diagrams used for consideration about possibilities of the direct one-stage metallic nickel production.

Jan 1, 1995

By Robert F. Jenkins, King G. Robertson

This paper presents a practical approach for utilizing a computer model to determine the mass balance for a typical UBC recycling complex - starting with raw materials input, through scrap preparation, delacquering, melting, alloy adjustment and casting. This model is especially concerned with metal unit losses throughout the recycling complex with emphasis on metal losses at the melting furnace. The model also addresses the application of hardener alloys, metallurgical salts, chlorine for demagging, and reagents for acid gas emissions control. Other issues addressed are dross generation, acid gas emissions and dirt and fines to landfill. One benefit of the model is the conversion of annual production objectives to hourly production rates and resource requirements taking into account production schedules, maintenance downtime, and operations inefficiencies.

Jan 1, 2000