Search Documents

By O. G. Rivera, R. D. Moser, P. G. Allison, W. R. Whittington, P. Rivera-Soto, Z. McClelland, D. Francis

This research examined the evolving microstructure of quasi-static and dynamically loaded fully annealed metastable 301 austenitic stainless steel (SS). Experiments were performed to an interrupted strain value of 20% and to failure using a tension Kolsky bar (1000/s) and an electromechanical load frame (0.001/s). Electron Backscatter Diffraction (EBSD) identified the microstructural evolution from the as-received condition to the 20% strain level for the high and low rate interrupted samples. This material achieved over 60% elongation to failure with increasing strength as strain rate increased, as expected. Fractography analysis using SEM showed particles in the microstructure and a ductile failure mode. The 301 SS exhibited a greater amount of phase transformation from parent austenite to -martensite at the dynamic strain rate when compared to the quasi-static strain rate during the interrupted experiments. This result is indicative of the increased propensity for austenite to -martensite phase transformations at the high strain rate.

Jan 1, 2016

By W. R. Opie

Fundamentals of blast furnace smelting of low grade copper and precious metal scrap and residues are reviewed with emphasis on emission control, by-products produced, slag cleaning for high recovery of metal values and the evolution of an off-gas system to eliminate hydrocarbons that result from decomposition of plastics in the blast furnace- charge. Problems with tin, antimony and nickel in the smelter-refining cycle are discussed.

Jan 1, 1985

By S. Y. Tan

As CMOS devices are scaled down into nano-region, SiO2 dielectric is approaching its physical and electrical limits. High-k material has been investigated widely in recent years, and gate oxide take place growth oxide with Hf-based below 45nm gate length technology node has been shown. The phenomenon of interfacial property between bulk silicon and gate dielectric materials (HfO2 and HfSiO) was focused. A comparison of capacitance-voltage (C-V) characteristic of gate insulator was presented. Furthermore, the electrical property and thermal stability of high-k dielectric materials at various post deposit anneal (PDA) temperatures were established. The X-Ray diffraction technique was (XRD) utilized to analyze crystallization of the thin films, and the X-ray photoelectron spectroscopy (XPS) was applied for surface chemical bounding energy to identify the silicon and dielectric layers. Results show that HfSiO films have exhibited a superior performance on both thermal stability and electrical performance.

Jan 1, 2009

By Y. Shigeno

The reactivity of a porous solid is a strong function of its pore structure (porosity, pore surface area and pore size distribution). It follows that reactivity could be altered by altering pore structure; one way to achieve this is by chemical vapor infiltration whereby a gaseous species is reacted in the porous solid to produce a solid. Experiments were carried out in which the pore structures of various carbons were modified by cracking methane within the pores; oxidation rates of the carbons were then measured for both infiltrated and original samples. For coke it was found that two indices of coke performance used in the steel industry (CRI and CSR) can be greatly improved following a small amount of infiltration. Infiltration/oxidation results are interpreted in terms of measured pore structure changes.

Jan 1, 1993

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Viscosities of FeO-SiO2-V2O3-CaO-P2O5 slags have been measured at the temperature range of 1673 K to 1773 K (1400°C to 1500°C). This investigated system represents the major components of basic vanadium slag that is an important intermediate product of a novel vanadium extracting process, in which removal of phosphorus and extraction of vanadium can be achieved from the vanadium-containing hot metal simultaneously. It was found that higher CaO/SiO2 ratio resulted in lower viscosity in the composition range of interest. Also, the viscosities increase with the increasing P2O5 concentration. The varying viscosities can be attributed to the modification in complexity and polymerization of the slag network. The variation of apparent activation energies are in tune with the viscosity measurements. The results of this work revealed the effect of CaO/SiO2 and P2O5 on the viscous properties of FeO-SiO2- V2O3-CaO-P2O5 slags and therefore provide the theoretical foundation for the control of the coupling de-P and V-extraction process.

Jan 1, 2016

By Jari Aromaa, Olof Forsen

"Oxygen evolution by decomposition of water is the main anodic· reaction in sulphuric acid solution. Traditional anode materials have been relatively low-cost lead alloys, though the active lead dioxide layer has a high oxygen evolution overpotential. This causes a significant increase of cell voltage. To lower total energy use in metal production, electrocatalytical properties or corrosion resistance to decrease replacement costs must be improved. Addition of an catalyzing ion will decrease oxygen evolution potential. The effective area of an anode increases by calcium additions and by producing anodes with fine microstructure. Remelting and rapid quenching is possibly a method that is economically feasible and technically simple enough to be adopted.IntroductionPermanent anodes are widely used in several electrochemical processes and cathodic protection applications. The permanent or ""inert"" anodes can be either massive or coated anodes. The massive anodes are metals, like lead alloys, or non-metals, like magnetite, graphite or ferrite. The coated anodes are made of a valve metal base (titanium, niobium or tantalum) coated with an electrochemically active coating. The purpose of anodes is to supply current to the electrochemical cell. A vast number of materials and their combinations are electrical conductors and may hence be used as anode materials. However, good anode materials must survive in aggressive environments and also be able to pass high current densities. These opposite requirements restrict the amount of possible materials. Generally, an useful anode material must meet three requirements, electrical conductivity, electro catalysis and stability. Good electrical conductivity is essential for energy efficiency. Good electrocatalytical properties are essential to improve product yield. Long term stability is also an important property, because electrode wear and corrosion may cause product contamination, increasing energy consumption and material and labor costs due to need of periodical maintenance. Electrical conductivity and electrocatalytical properties are more widely studied subjects than long term stability of anodes, and a good amount of information about these two subjects can be found in the open literature. Wear and corrosion mechanisms of the anodes vary depending on the operational conditions, i.e. concentration of different species, temperature and operating current density."

Jan 1, 1997

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By Jian Li, S. Penttilä, P. Liu, W. Zheng, C. Bibby

"The materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. The current Canadian pressure-tube supercritical water (SCW) concept design requires core outlet temperature of 650 °C at 25 MPa with peak cladding temperature reaching as high as 850 °C. Aside from oilier challenges, there is currently very limited data on candidate stainless steels' corrosion resistance under this operating condition. Austenite stainless steels that include 316L, 304H, AL6XN and 3 l0S that cover a wide range of Cr contents are promising candidates for either direct in core applications or as base coating materials. However, their corrosion resistance has not been tested systematically under this stringent condition. In this study, these types of stainless steels are tested, and their corrosion resistances are compared.IntroductionThe Canadian pressure-tube supercritical water (SCW) concept will operate at a core outlet temperature of 650 °C at a pressure of 25 MPa, with potential peak cladding temperature reaching as high as 850 °C. High-temperature corrosion resistance is one of the key design requirements for fuel cladding components. As summarized by Allen [1 ], most testing to date has been carried out at temperatures below 730 °C. To date, SCW corrosion data above 600 °C is very limited. Even at relatively low temperature exposure to SCW (e.g. 500 °C), F/M steels develop a thick oxide layer rapidly, while some austenitic stainless steels develop thinner surface oxide. Ni based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of intermetallic precipitates [2-5]. Dissolution of major alloying components from all of these alloys could also pose significant problems for downstream piping [6]. Kaneda et al. [7] suggested some modified stainless steels provide better SCW general corrosion resistance, with no sign of SCC under the slow-strain rate test.Cho [8] suggested that as the Cr content increase, general corrosion resistance improved at 510 °C and 25 MPa. However, similar to Cho's work, most of the SCW corrosion resistance assessments were based on weight change measurement. This can be unreliable due to potential exfoliation of thick oxide film. Besides, there have been no systematic SCW corrosion resistance tests for candidate stainless steels under higher temperatures. SCW corrosion rate increase dramatically for alloys tested at 600 °C [1]. It is also important to understand the role of major alloying elements under this stringent operating condition, not only for fuel cladding components' materials selection, but also for coating materials development."

Jan 1, 2013

By Jae-Chun Lee

One of the main advantages of the supported liquid membrane(SLM) would be that different kinds of ions can be extracted selectively or simultaneously from multi-component solutions by parallel treatments with multi-SLM units. This distinctive feature of the SLM extraction is originated from its non-dispersive contacting operation between organic and aqueous phases. In this study, simultaneous and selective extractions of zinc and copper ions from their mixed solutions have been demonstrated using two parallel modules of SLMs. PC88A and LIX84 were used as the extractants for zinc and copper, respectively, and the Hoechst Celanese hollow fiber modules(Liqui-Cel Lab Module) as the supporters. The performance of the simultaneous system was compared with those of the system in which the extraction of each component was achieved by individual runs

Jan 1, 1998

By Takamitsu Nakasuga, Haiping Sun, Kyushu University, Katsumi Mori

"The kinetic behavior of reduction of chromite ore by liquid iron containing carbon and silicon has been investigated under various experimental conditions to clarify the reduction mechanism. It was found that the reduction rate of chromium ore by liquid Fe-C alloy was very slow. In addition, when carbon and silicon coexisted in the iron melt, silicon was found to preferentially oxidized to form silica, which favored for the fonnation of liquid slag and the rate of reduction was considerably accelerated. The similar effect was obtained by the addition of some fluxes, such as SiO2, Na2B407, CaO-SiO2, which also promoted the formation of a liquid slag and thus the reduction rate in the early stage also increased.IntroductionThe reduction of Cr2O3 is a basic reaction for production of ferro-chromium from chromite ore and for chromium recovery from the slag fonned during the decarburization period of a stainless steel-making process. The reduction of chromite ore consumes much energy and its reaction rate is not so high. Thus, in order to increase the reduction efficiency, it is strongly desired to clarify its reduction mechanism from the practical and the theoretical points of view."

Jan 1, 2000

By Elli Miettinen

In Copper Flash Smelting operation disturbances may lead into dust build-up in the gas train and off-gas handling system causing reduced heat recovery efficiency and process availability. Flue dust of a Copper Flash Smelting process heat recovery boiler has been characterized and its thermal conductivity and diffusivity have been determined. Dust accretions consist of several layers possessing varying particle sizes, densities, and thermal properties, with the binding phase usually being sulphate. All the dusts can be regarded as effective thermal insulators with thermal conductivity values of less than 2 W/mK and thermal diffusivity values of less than 0.005 cm2/s. Porosity can be regarded as a fairly good indicator of the thermal transport efficiency of these types of materials, but the material microstructure must also be considered. The results can be used in the dimensioning of metallurgical heat recovery boilers and they also provide accurate input data for process models.

Jan 1, 2009

By Mike Santaluce

Smelting furnace rebuild projects often require a significant capital expenditure and an extended smelter outage. Smelter operators are increasingly searching for methods and initiatives to shorten furnace rebuild schedules, maintain manageable cost levels, enhance furnace performance and achieve excellent safety results. This paper describes the ?MEPC? Model for furnace rebuilds; a project driven approach which Auburn has developed in response to the need for improving furnace rebuild project outcomes. The ?MEPC? (Management, Engineering, Procurement and Construction) approach better addresses the unique challenges presented by furnace rebuild projects when compared to the traditional EPCM (Engineering, Procurement, Construction Management) model widely in use for these projects today. One key feature of the MEPC model is that a dedicated project management team with representation from all of the major project stakeholder groups is put in place at the onset of the project. The project management team has ownership and accountability for meeting overall project goals over the entire lifecycle of the furnace rebuild project. A second key aspect of the model is emphasis on project management as a completely separate project function with its own specific skill sets, techniques, tools and best practices. These features of the MEPC model offer several advantages in terms of improved planning, coordination, communication and alignment with project goals which contribute to the overall success of furnace rebuild projects. Similar MEPC concepts have been used to deliver excellent project results in other industries and the MEPC approach has been successfully utilized on furnace rebuild projects.

Jan 1, 2006

By C. Cánepa

In the treatment of many problems related with the optimization of a given ore dressing process, microscopic studies can provide invaluable assistance. Such studies are generally carried out through mineralogical determinations both qualitatively and quantitatively. Frequently the solution of a specific problem requires the combination of these in adequate proportions. Often the nature? of the problem poses some conditions regarding the way the microscopic determinations are made in order to yield useful information. Most publications applied to mineral beneficiation show results of ore microscopy without mentioning the methodological details involved in the determinative work and therefore it is not possible to judge their reliability and/or their relevance. As methodology must necessarily change from case to case, it is very important for the microscopist to identify first the direct and indirect mineralogical information required to solve the problem. Without such guidelines selection of methods for the qualitative and/or quantitative determinations cannot be made.

Jan 1, 1981

By Sadegh Safarzadeh, Anne-Marie Suriano, Stanley Howard

The electrodeposition of metal ions from aqueous electrolyte solutions has been a well-known process for the last half century. With numerous industrial applications such as electroplating, electrowinning and electrorefining, the kinetics of electrochemical reactions involved in the process has been extensively researched. Arrhenius-type rate equations, the Butler-Volmer equation, and the empirical Tafel equation are among the most important models to explain the rate of electrochemical reactions. The study of the kinetics of metal deposition is critical to understanding the underlying mechanisms through which a certain morphology of metal deposit is formed on the cathode. The purpose of this paper is to elucidate the influence of experimental parameters such as pH and additives on the rate and the reaction mechanism determining the rate limiting step of the electrodeposition reactions.

Jan 1, 2015

By C. Twigge-Molecey

All projects that are implemented, have been given corporate go-ahead on the basis of a set of clearly defined targets. These are typically a production goal at a capital cost, operating cost and production schedule, that will yield an acceptable return on investment by the companies internal criteria. The challenge for the implementation team is two-fold, firstly to properly define the project criteria prior to board approval and secondly to deliver an operating facility that meets these objectives, in particular the ROI. The paper addresses the issues a project team and the company management must address for a successful project. Key questions that will be explored are: ? What is the status of key technologies? Are they well proven in commercial practice, completely novel or in between? ? Is the project schedule driven by market constraints or cash flow constraints? ? Are the risks of fast tracking worth the potential rewards? ? For a retrofit project, are all the technical and production interfaces and issues known at the time of approval to proceed? ? How much should be invested in technological development and engineering and at which phase? ? For an owner-operator, how much responsibility is it wise or appropriate to push down to vendors? The answers to these questions for a specific project will define how you go about a project, the resources required, the contracting strategies, the phasing and the appropriate level of investment in the definition and procurement phases, prior to starting major capital commitments and construction.

Jan 1, 1999

"An experimental study has been performed to investigate the dispersed phase holdup induced by a high-strength submerged gas injection in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor using two different tuyere configurations. The air flow rates varied from 0.00599 m3/sec to 0.01312 m3/sec. In these series of experiments, water height and kerosene height were kept constant at 0.23m and 0.02m respectively. The dispersed phase holdup was determined at various gas flow rates, and tuyere orientations by using water and kerosene.The dispersed phase holdup increased with gas injection rate and decreased with vertical distance from the original interface. At constant gas flow rate, as the vertical distance increased in the centerline, off-center configuration of nozzles displayed higher values of the dispersed phase holdup than those of the center configuration. The variation of the dispersed phase holdup with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the calculated values obtained from the correlation equations."

Jan 1, 1999

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By Kai Tang, Casper van der Eijk

Natural gas has been used as reductant in the production of iron for several decades. Recently, the use of natural gas as reductant for other metals has been drawing attention because of the low price of natural gas, as well as the reduction of CO2 emissions compared to the use of coke and coal. In this work, the reduction of a mixture of Ti- and Ni-oxides by natural gas has been studied. Within the Ni-Ti system, the intermetallic compound Ni3Ti is thermodynamically the most stable one. Therefore, powders of Ni-oxide and Ti-oxides were mixed in an atomic ratio of three to one and subsequently pelletized. Reduction was performed in a TGA furnace at constant temperature with varying reducing gas atmospheres. In a natural gas containing atmosphere, the Ni-oxide was easily reduced to metallic nickel while the Ti was reduced to Ti-oxycarbides or Ti-oxynitride when nitrogen was present. Depending on the process parameters, several percent of Ti was dissolved in the nickel-based solid phase.

Jan 1, 2014

"Recycling of solid wastes plays an important role in environmental protection. However, solid wastes are often contaminated with some undesired components so that many of these solid wastes are hardly economically recycled. Therefore, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes. There exist three general strategies of separation of undesired components from solid wastes: before-process separation, post-process separation and in-process separation. In this paper, different separation strategies are discussed in terms of energy requirement and availability, implementation complexity and additional need for environmental protection. It is concluded that of all separation strategies, in-process separation has the least energy requirement, the least implementation complexity and the minimum need for additional environmental protection.IntroductionIn industries, solid wastes almost come with every production process. Multi-million tons, if not billion tons, of solid wastes are being generated globally each year. These solid wastes are lowvalue materials in general, and often have very limited markets. As a matter of fact, many of these solid wastes have been stored on site or have been disposed of at landfills for many years, not only occupying lands, but also polluting environment. Therefore, effective and efficient recycling of solid wastes has been a very challengeable task and has played a very important role in environmental protection.One of the major barriers which hinder recycling of solid wastes is contamination of the solid wastes with some undesired components. These undesired components are components which are not wanted by production processes or applications where the solid wastes are consumed or recycled, since the undesired components often degrade qualities of the solid wastes, imposing negative effects on operations, facilities and product qualities of the production processes or applications. Sometimes, the undesired components may also pose severe environmental concerns. When undesired components are present in solid wastes at over-limit levels, the solid wastes tum to become destructive, useless and non-recyclable. Consequently, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes."

Jan 1, 2014