Search Documents

By Katsunori Yamaguchi

The zinc, lead and alumina contents in copper smelting slag are increasing with the increase in waste recycling. The recovery of base metals such as lead and zinc from copper converter slag is important from both an economical and environmental perspective. As a fundamental study of the metal recovery by reduction process, activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag under iron saturation at 1573K are derived from the data of slag-metal equilibrium experiments. On the basis of the obtained data, the activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag were compared with those of the CaO-SiO2-FeOx ternary system. Addition of alumina increases activities coefficient of ZnO and PbO in SiO2 rich side of the slag, and decreases them in CaO rich side.

Jan 1, 2006

By Burkhard Seeger et al.

The oxidation of copper sulfides can be highly accelerated in the presence of nitrous gases (NOx) as reaction catalysts. Sulfur and sulfate are simultaneously produced in this highly exothermic reaction. This process, carried out in sulfuric acid medium, is performed at an approximately normal pressure and at a temperature of around 110 °C, in a closed container, adding either oxygen or air. The oxidation is automatically controlled through a computer. The process covers the following steps: Catalytic oxidation, filtration and crystallisation of the hot concentrated liquid, electrowinning, mother liquor treatment through jarosite formation, recovery of dissolved copper and zinc and regeneration of industrial water, and non-soluble residue treatment with extraction of sulfur and recovery of silver and gold. No combustibles are needed. No air is contaminated, and no waste water is produced. Solid residues are in a stable, non-toxic and non-corrosive state of equilibrium. Risk of accident is low. Investment costs are small compared to those of the comparable pyrometallurgical process, and production costs are competitive.

Jan 1, 1999

By V. A. Bryukvin

A characteristic feature of the macrokinetics of the interaction process is the presence of two specifically defined areas of oxidation which had a linear time dependence. The effect of variables, such as residual sulphur content of the melt, temperature and the oxidation potential of the gas phase, on the macrokinetics of oxidation are investigated. Phase composition and structure of products of solidification of partially oxidised melts and thermodynamic properties pentaining to Cu-S-O melts are used to analyze the macrokinetic behaviour and mechanisms of the interaction. The process of interaction of sulfide copper melts with oxygen may be considered as a disproportional absorption process and its mechanism is based on localized interaction on the surface and inside the melt volume. Superficial processes include also the process of primary chemisorption of oxygen by melts at place of metal-metal donor bonds proceeding with formation of oxysulfide liquid solutions and volumetric decomposition of the latter accompanied by evolution of sulfur dioxide and metallization of sulfide melts. It is the degree of dynamic balance of such interaction processes that determines specific individual features of the macro-kinetics and mechanism of oxidation of sulfide copper solutions with oxygen in the gas phase.

Jan 1, 2006

By Jimsher N. Aneli

There are many experimental works on the investigation of temperature effect on the conductivity of polymers filled by carbon materials. However frequently the establishment of current nature in the polymer heterogeneous systems becomes difficult. This fact is explained by complexity of calculation of different physical or chemical phenomena passing in materials at variation of the temperature. Among these phenomena it must be noted some morphological changes in the structure of polymers. These changes reflex on the structure of conductive system of composites. So, it has been shown, that the character of temperature dependence of thermal noises level and conductivity of some polymers filled by carbon black essentially depend on some relaxation transition in the polymeric matrix. In this paper the effect of difference transitions in polymer matrix of filled by carbon black some polymers and rubbers have been investigated in a wide temperature range. The importance of such investigation is due to possibility of application of resistive temperature sensors based on conductive polymeric composites (CPC) to measuring technology. The experiments have been carried out in the cavity with regulation of temperature in the range 110-650K. The resistance of samples was measured by four electrodes method. The samples were obtained by hot pressing of dry mixture of powdered components at chosen temperatures, pressures and cooling time in the case of plastics and by peroxide vulcanization of the elastomers in the case of the rubbers. The samples were produced on the basis of the following thermoplastics: low density polyethylene, polytetrafluoroethylene, polycarbonate and polydimethylmethylvinilsiloxane.

Jan 1, 2006

By A. Alvarez

In this work, mesophilic and thermophilic cultures have been used in the presence of silver as a catalyst. Chalcopyrite and byproducts of bioleaching were characterized in order to: a) obtain information about the kinetics control of the process, and b) explain the different behaviour observed during the mineral attack. With thermophilic microorganisms (68°C and Norris medium as nutrient) the reaction stopped at approximately 65% copper extraction, with and without Ag ion addition as a catalyst. The remaining chalcopyrite appears surrounded by hydronium jarosite (with ammonium ion in substitution in the "alkaline site"), goethite and elemental sulphur. With mesophilic cultures (35°C and 9K medium as nutrient) the reaction stopped at approximately 25% copper extraction (without Ag) and approximately. 85% extraction (with Ag). In both cases, the remaining chalcopyrite was surrounded by agglomerates of ammonium jarosite (with hydronium ion substitution in the "alkaline site") and some iron oxides and/or hydroxides.

Jan 1, 1999

By C. García

Several modifications to Zaldivar's original design have been made in order to reach the design cathode production. This paper describes the modifications to the crushing, leaching, solvent extraction and electrowinning operations, which in turn have increased the production by 14.8% over the design capacity in 1999. The principal modifications were to (1) incorporate a dry pre- screening plant between the secondary and tertiary crushers to increase the percentage of fines to the piles, (2) increase the retention time of the solutions inside of the piles, and (3) increase the efficiency of the tertiary crushers to reduce the particle size of the product material. The leaching ratio was increased from 2.8 to 5.6 m3/ton. The temperature of the pregnant leach solution (PLS) was increased, the amount of acid used was reduced, and a strain of native bacteria was adapted in highly contaminated solutions. The copper concentration in the PLS was increased by more than 50% and was stabilized at this level by commissioning a process of two-stage leaching. The current density in the tankhouse was increased from an average of 2 16 to 3 17 A/m

Jan 1, 1999

By Katsunori Okaya, Gjergj Dodbiba, Hiroyuki Ono, Toyohisa Fujita, Seiji Matsuo

"In an attempt to raise the copper grade of Printed Circuit board (PCB) by removing other components, carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under nitrogen atmosphere. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The liberation of copper foil from the oversized pieces was also investigated. The copper foil was liberated easily from glass fiber by stamping treatment. Liberation rate of copper foil was high at high carbonized temperature. The experimental results indicated that 90% of oversized char was liberated and the copper foil recovery from PCB carbonized at 1073K was 110kg/t. The copper recovery from char powder by flotation was also investigated. 15% of the copper grade and 80 % of the copper recovery were obtained, whereas the removal rate of silicon was 55%.IntroductionWaste Electrical and Electronic Equipments (WEEEs) should be recycled because they have many kinds of valuable materials and most WEEEs include Printed Circuit Boards (PCBs). In Japan, about 30 km2 per year of Printed Circuit board (PCB) has been produced [1], PCBs are normally separated from WEEEs and picked up by hand and sold to non-ferrous metal market because PCBs include high grade of copper and other precious metal such as gold, silver and palladium [2]. However, PCB also has impurities such as silicon, aluminum and calcium which are slag materials in non-ferrous smelting process, and other harmful elements such as lead, bromine and antimony. Low grade PCBs are sold after removal of invaluable parts or sometimes land filled without any treatment"

Jan 1, 2011

By H. Singh, Anupam Agrawal, H. S. Grewal

"Erosion in industrial appliances causes huge loss of valuable resources especially when solid particles are present in the working medium. A number of erosion models that are available in the literature claimed to predict the erosion response. In this work, five erosion models have been evaluated using computational fluid dynamics (CFD) methodology. Three most commonly used experimental test rigs (solid particle and unsubmerged slurry jet type and pot type) have been simulated and comparisons with the experimental results have been performed. The study helps in understanding the effect of fluid medium and flow pattern on the erosion process. The knowledge acquired shows that phenomenological based erosion models give better results considering the wide range of operating parameters. The in-depth study of the flow field shows the possibility that erosion mechanism, being parameter dependent, could change with location on the same specimen.1.0 IntroductionErosion is a surface degradation phenomenon which causes the removal of material due to impacts either of solid particles and/or bubbles or gas entrained in a fluid medium. Erosion has various categories depending upon the erosion medium such as, solid particles erosion (solid particles entrained in gaseous medium), slurry erosion (solid particles entrained in liquid medium) or cavitation erosion (erosion caused by exploding gas or vapor bubbles). Humphrey [1] has listed 21 different factors that decide the erosion response of the components under a given working condition. The number of factors involved in the erosion process gives us an idea about its complex nature."

Jan 1, 2012

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the influence of Fe+2 initial concentrations in the bioleaching of copper from printed circuit board using Acidithiobacillus ferrooxidans-LR. Printed circuit boards were collected from obsolete computers and mechanically processed through size reduction followed by magnetic separation. The bacteria Acidithiobacillus ferrooxidans-LR were grown and adapted in presence of printed circuit boards. A shake flask study was carried out on the printed circuit boards samples (non-magnetic fraction) using a rotary shaker under the following fixed conditions (185 rpm, 30°C). The bioleaching efficiency was evaluated by comparison between the concentration in the initial sample and in the leached liquor, pH of the medium and concentration of ferrous iron produced. Inductively coupled plasma optical emission spectrometry (1CP-OES) was used to determine the metals concentration. The results showed that Acidithiobacillus ferrooxidans-LR leached 63% copper from printed circuit boards using supplemented medium with Fe+2.IntroductionThe waste of electric and electronic equipment is generated by discarding of equipment such as obsolete computers and cell phones which is stimulated by the technology innovations and it has been growing each year. Because of the amount that has been accumulated it has become a prominent environmental problem but also can be a source of valuable materials, such precious and base metals [1,2] The printed circuit boards are found in almost all electric and electronic equipment being composed of polymers, ceramics and metals and can be an alternative source to recover base and precious metals. The precious metals are used in the printed circuit boards to protect against oxidation and base metals because of its conducting properties [3]. The heterogeneous composition of printed circuit board is a limiting factor in the recycling processes and the metals concentrations also range."

Jan 1, 2011