Search Documents

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology, The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty., and the, rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut n. On October 9, 1931, permission was granted t o reopen and prod e the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that hid not produced more oil than specified under the earlier proration orders and that had been shut in for the required 55-day period were permitted to produce 5 percent of their last potential during that 10-day period. On November 7, 1931, the Corporation Commission of Oklahoma issued an order which divided the Oklahoma City field into the Wilcox, Arbuckle, and Lower Simpson zones for proration purposes. Wells producing from the Wilcox zone were allowed to produce 4 1/2 percent of their potential5/ from November 1, 1931, to January 1, 1932; Arbuckle limestone wells were allowed to produce 250 barrels of oil daily; and Simpson sandstone wells which had a potential of over 2,000 barrels per day or which made 3 percent or more water were allowed to produce 200 barrels of oil per day.

Jan 1, 1937

By G. Richards

Research shows that having more women in the top mining jobs can bring bottom-line benefits. Mining companies are starting to embrace the need for greater gender diversity at board and senior management levels, figures and examples are given.

Jul 1, 2015

Tapira Mine (Tapira, MG, Brazil) is the largest phosphate ore and concentrate producer in Brazil. The mine is an open pit, which until recently operated with a large equipment fleet and now uses a smaller fleet operated by contractors. The annual production reaches 17 Mt of ore plus 14 Mt of waste at a stripping ratio of 0.82. Defining the geological boundaries and forecasting the annual production can be a difficult task if not performed on a reliable model. The geological model has been totally reviewed as well as the estimation process. Ordinary Kriging has been used to build the new block model with P2O5 and contaminant grades. After estimation, block model validation and classification criteria definition to assess resources and reserves, the result is given by the life-of-mine plan is defined after pit optimisation and design. The Lerchs-Grossmann algorithm implemented in the NPV Scheduler was used to define the long-term production targets based on the main parameters P2O5 and the contaminants that are just important to the beneficiation process.

May 1, 2010

By Wils L. Cooley

The report covers several aspects of mine safety ground systems, primarily for underground coal mines. The design of a combined ground fault-ground check monitoring system is presented. An analysis is made of grounding systems for dc shuttle cars. Complete resistance data and results of physical inspections of self-salting ground rods are presented. A detailed resistance and economic analysis is presented for the use of composite materials for building inexpensive and effective ground beds in high-resistivity areas. The desireability of penetrating the coal seam with a borehole safety ground is investigated. A report is made of a Mine Substation Grounding and Bonding Workshop.

Jan 1, 1980

By Fredrick Fränding

In mining and quarrying operations, electric motors can fail for a variety of reasons. Some failures are directly linked to demanding production requirements and contaminant-laden environments and, consequently, are difficult to prevent. A sizeable number, however, are caused by ?offline? factors that have nothing to do with production. These include inadequate or substandard motor repair practices and improper motor shipping, storage and installation. The fact that failures are at times attributable to repair- or rebuild-related errors and problems raises the stakes when selecting an electric motor repair provider. Teaming with high-quality electric motor shops can help a company reduce failures due to offline factors, improving motor reliability and cutting downtime costs. Regardless of location or annual revenues, the best motor shops have similar business cultures and share many of the same characteristics.

Jan 1, 2009

The corrosion of aluminosilicate refractories by soda from three different sources has been studied by microscopic methods. Sodium sulphate from oil ash, sodium chloride used in glazing structural clay products, and sodium borate from borax-impregnated wood ash have fundamentally the same effect on the refractories. The soda is the chief medium of reaction and fluxing, the sulphur, chlorine, and boron being volatized as sulphuric, hydrochloric, and boric acids.INTRODUCTIONBecause of their strong fluxing action, alkalis are one of the main causes of corrosion and slagging of refractories.The action of potash and soda on refractories follows somewhat similar lines, although it is common for one alkali to be greatly in excess of the other. The course of the reaction in a number of cases of alkali attack has been studied by microscopic and chemical methods. For example, the action of potash on blast furnace refractories was studied by Kraner (1942) and Rigby and Richardson (1947), who described the occurrence of various potassium aluminium silicates. Its action on cement kiln refractories was described by Brisbane, Segnit, and Weymouth (1957). The action of soda on glass tank refractories has been studied by many people, for example Bisby (1956) and Resch (1954). Clews, Hugill, and Green (1940) made a microscopic examination of the attack by soda on silica bricks from a gas retort.Some recent cases of corrosion of aluminosilicate refractories which were brought to the attention of the Division of Building Research, C.S.I.R.O., illustrate phenomena which occur under conditions different from those...

Jan 1, 1964

By E. L. Garton

Michigan is becomining one off the important oil-producing States of the country, The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 1935.4/ The Bureau of Mines method of crude-oil analysis and classification indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the tame amount of kerosene and gas-oil combined, 12 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue of about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in S counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By Miezitis Y

A weak airborne radiometric anomaly was examined in the field and the presence of uranium confirmed. Rotary-percussion drilling showed the presence of uranium but a subsequent programme of diamond and rotary percussion drilling indicated that the concentration of uranium was uneconomic. Within the tufts and volcanics of the prospect the uranium existed as uranyl phosphates within the oxidized zone. Geological mapping and the diamond drill core showed that the Stag Creek Volcanics are part of the Lower Proterozoic Masson Formation, probably with member status, rather than the expression of an Archaean basement ridge. This change in the interpretation of the fundamental structure of the Pine Creek Geosyncline has led to a reexamination of the stratigraphy and to suggestions which differ from the current concept.

Jan 1, 1977

By I. Liebman

The Bureau of Mines conducted experiments on coal dust explosion suppression. The investigation took place on a beltway in the double-entry of the Bureau's Experimental Mine. Using conditions that simulate those in a working mine, the investigation showed that a coal dust explosion can be readily initiated in a conveyor belt entry. Also, the explosion can spread into adjacent entries through opened crosscuts (stopping destroyed by explosion) to propagate for long distances even though the adjacent entries are rock dusted in compliance with regulations. Passive water barriers (water-filled tubs) were found to be effective in suppressing explosions on a beltway; however, barrier efficiency was reduced by opened crosscuts. The study indicated that the beltway barrier should be the distributed type consisting of continuous rows of water-filled tubs covering long distances along the entry. A plan is outlined for the installation of a water barrier system in a working coal mine for the protection of a beltway.

Jan 1, 1981

By P O. Koons, R J. Norris, S C. Cox

 The Southern Alps is an active oblique collisional zone which has a characteristic wedge-shaped geometry above a low-angle ductile shear zone. The Main Divide region is a relatively low strain zone above this ductile shear zone, and is _deforming principally along steeply dipping strike-slip faults. Extensional fractures are common at a high angle to the regional structural trend. These steeply dipping structures act as conduits for gold-bearing fluids from depth, and small mesothermal gold deposits have formed at several structural levels including the near-surface region. Gold has also been deposited in a meteoricmetamorphic fluid mixing zone near a conductive thermal anomaly on the western slopes of the mountains. These various gold deposits and their well-constrained structural and tectonic settings can be used as analogues for larger, deeper-eroded mesothermal gold deposits in the Mesozoic Otago Schist belt. High level Miocene veins in NW Otago have formed beneath the main divide of the initiating Southern Alps. Late metamorphic gold-bearing veins formed as fluid escaped from the ductile-deforming crustal root beneath Mesozoic mountains.  

Jan 1, 1997

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By Alejandro Ferrada Vergara, Héctor Espinoza Muñoz

Drilling and blasting stages are considered factors that impact downstream processes significantly and over all the mining business value chain. Adequate control of these processes may represent energy savings in comminution processes. There has historically been a resistance to design change as this implies more drilling and implementation costs due to new technologies in explosives, which added value is difficult to quantify.

Jan 1, 2016

By T. Celik, B. Genc, C. Musingwini

"Mine planning software continues to be an important factor when it comes to the development of the South African mining industry. To contribute to this development, a new methodology to define and measure mine planning software utilization in the South African coal mining sector within an evolving data-set framework was developed. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgy in 2013. In 2014 the data-set was updated with additional and new information.In this paper, using the 2012 and 2014 time-stamps, a methodology for estimating the software utilization is developed. In this methodology, three variables: commodity, functionality, and time factor are used to define and measure the software utilization in order to ultimately inform decision making strategies for software utilization. Utilization in the coal sector was measured according to six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation and Optimization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and wanting to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2016

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160ºC and 1,380 kPa (200 psi) oxygen overpressure, DEW to produce LME Grade A cathode, recycling of the lean electrolyte to the pressure leaching step and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of the lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an ?acid-autogenous? process referred to as the ?MT-DEW-SX? process. This paper (Part III) discusses the steps taken to develop and complete a large-scale demonstration of the process at Bagdad, Arizona, in 2005.

Jan 1, 2007

By T N. Little

The author contends that geoscience is presently under-utilised in the rock fragmentation by blasting process. Before we can set standards in this area, the following is required: mine geologists need to gain a better understanding of the blasting process and the blasting team needs to obtain a better appreciation of geology. Both groups need to be informed of what can be done to improve blasting outcomes, why it is necessary and how it can be achieved. By working closely together, both the geoscience toolkits and blasting expertise can be applied and focused on priority blast sensitive issues, with potential to improve mine economics and safety. Finally, and ideally, mine geologists need to take a leadership role in raw rock mass data collection and data management, and invited to take an active role in rock mass related behaviour data collection, integration and presentation.This paper attempts to provide insight into all these prerequisites for setting a new standard for collaboration and mutual learning in this strategic opportunity area. The potential for blasting to leverage downstream processes is highlighted. Blasting objectives and blast design principles are introduced along with the required rock mass related inputs. Some hazardous geological materials and environmental conditions are described, along with how they can affect operational complexity.Four case examples are used to illustrate the need for closer liaison between geology and blasting professionals. The first related to grade control blasting, aims to demonstrate how a blasting geology approach can add significant value. Case example two demonstrates how geological models and bench face analysis can assist with fragment control. The third and fourth case examples involve an overview of two case studies where timely geological and geotechnical knowledge input and intervention into blasting activities may have reduced losses due to blast initiated open pit slope collapses.CITATION:Little, T N, 2017. Geoscience input into blasting operations – let’s set a new standard, in Proceedings Tenth International Mining Geology Conference 2017, pp 375–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Niels Kofoed

Upon completion of the 6,200 m (20,340 lineal ft; lft) North Tunnel drive for the Portland East Side Combined Sewer Overflow (CSO) Tunnel project in Portland, OR, the slurry tunnel boring machine (TBM) had to be returned from the Port Center shaft at Swan Island to the Opera shaft at the main mining site for the 2,700 m (8,860 lft) South Tunnel drive. At the Port Center shaft, the main 513-t (565-st) TBM and TBM tailshield were hoisted out of the shaft in two pieces using four 200-t (220-st) strand jacks mounted on a 635-t (700-st) hydraulic boom gantry system supported by Emmert International?s custom gantry tracks designed to span the shaft. After lifting the TBM components out of the shaft, the gantry system loaded the TBM components onto two Goldhofer platform trailers, which then transported the TBM and tailshield to a barge using a roll-on/roll-off method.

Jan 1, 2011

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963