Search Documents

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By Steven Townend

Mining-related activities have been known to create a challenging operating environment for mining companies located in close proximity to communities. Issues such as noise, vibrations from mining operations, land use and emissions are often a concern for community residents. In order to develop good community relationships it is necessary to take a proactive approach. This paper documents this approach and also deals with the social implications for Vale associated with mining activities in the heart of the community of Copper Cliff, Ontario, Canada.

May 1, 2011

Evaluation of Comminution Circuit Design for Sustainability Using EcoNomicsTM

Sep 13, 2010

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By A. Duerksen

"Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. Over the years, the coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research discussed in this paper investigates one potential solution - or component of a solution - to improve the sustainability of surface coal mining in West Virginia: post-mining wind power. The paper begins with an introduction to the Appalachian region of the U.S. and the role that mining has played in its history, followed by a discussion of the need for sustainable mining and how post-mining wind power may help fulfill it. Data processing methodology of field data from monitoring locations is then explained. The results are then used to estimate the electrical output of a wind turbine. This data is then utilized in a case study discussion of one of the monitored sites. The paper concludes with an analysis of the broader implications of the research and a discussion of future work."

Jan 1, 2011

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By Robert Hopler

That some time in the year 1872 there was organized an association composed of practically all of the manufacturers of gunpowder and other high explosives in the United States, the members of which said association were as follows: E. I. du Pont de Nemours & Co., The Hazard Powder Company, Laflin & Rand Powder Company, Oriental Powder Mills, American Powder Company, The Miami Powder Company, and Austin Powder Company of Cleveland, all of which or their successors are defendants herein; that the object and purpose of said association was the elimination of all competition between the members thereof in the shipment and sale of gunpowder and other high explosives among the various States and Territories of the United States; that the only manufacturers of gunpowder and other high explosives which did not join such association at the time of its organization were the California Powder Works, The Sycamore Manufacturing Company, and The Lake Superior Powder Company, but your petitioner alleges that each of said three last named companies

Jan 1, 2008

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986

By Fanke Meng

Electrolyzing oxides of titanium, aluminum and niobium could prepare high-Nb bearing TiAl alloy (Ti-45Al-9Nb) at 1500°C. The chosen electrolysis voltage is 3.5V, which is lower than reducing voltage (~4.7V) of electrolyte CaF2, but higher than that of titanium, aluminum and niobium oxides. The investigation shows that compared with traditional methods, this method for preparing high-Nb bearing TiAl alloy is of many advantages such as few steps, friendly environment, low energy consumption, low cost and high current efficiency.

Jan 1, 2009

By R. J. Pine, J. S. Coggan

Distinct-element modelling has been used to study the mechanisms associated with observed deformation of the western face of the quarry. A complex failure mechanism involving distinct planar surfaces that was proposed for a slope failure in 1967 has been modelled and shown to be plausible. In addition, deep-seated flexural toppling may contribute to the slope instability. Modelling has confirmed the detrimental influence of a raised water-table on the stability of the slope and also indicates that the observed cyclic opening and closing of tension cracks may be attributed to seasonal rise and fall of the groundwater level

Apr 1, 1996

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Thomas M. Gurtowski

This paper presents a summary of allowable bearing pressures and skin friction values that have been used to design drilled pier foundations for support of high-rise structures in downtown Seattle, Washington. These design parameters are based upon a review of geotechnical reports and records of more than 20 building projects. The following pages present a description of the soils encountered at these sites including foundation bearings soils, and design bearing and friction values. The accumulated data is summarized in Table 1, and the locations of the buildings are shown in Figure 1. A detailed description of the construction of two belled drilled piers are presented illustrating typical methods and procedures used in downtown Seattle. The two cases are from the Washington State Convention and Trade Center (WSC&TC). SEATTLE AREA SOILS The Puget Sound area was subjected to several major glaciations during the Pleistocene Epoch. Glacial ice originated in the cordilleran and coastal mountains and the Vancouver Range of British Columbia. The maximum southward advance of ice reached the area about halfway between Olympia and Centralia. As a result of these glaciations, the Puget Lowland was filled to significant depths by glacial and non-glacial sediments during the Pleistocene.

Jan 1, 1990

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011