Search Documents

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Phases of the Ir sub-group are present either as inclusions in or interstitially to chromite and are unaffected by (or only altered in situ during) hydrothermal processes. By contrast, almost all phases of the Pd sub-group are located in a secondary textural setting - in fractures in chromite or between fragments of brecciated chromite. The different settings indicate that the mineralisation episodes were associated with magmatic and hydrothermal stages respectively. The presence of an included Pd-group mineral in a hydrothermally Pd-group mineralised chromitite sample suggests that the hydrothermal Pd-group minerals were at least partly derived by remobilisation from magmatic deposits in the chromitite pod. These observations indicate that Pd-group elements are more mobile than Ir-group elements under hydrothermal conditions and point to the potential for hydrothermal platinum and palladium mineralisation in favourable environments

Apr 1, 1994

By Liping Yu Che, Xiaotie Wang, Mingli Cao, Jizu Yongfu Yuan

"It is difficult separating fluorite from Ca, Ba, Si intergrowth minerals than simple from Si, using common reagents such as combination of oleic acid or paraffin soap and water glass, but the finest quality fluorite concentrate whose grade is over 96%F must be required in chemical plant.This paper studies the flotation process of native fluorite from calcite, barite and silicate minerals whose flotation properties is similar to fluorite, using new effective collector H602 and new depressor S602 that is cheaper in cost, and describes the flotation properties. In order to determine optimum flotation separation condition, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents on flotation were investigated and the flotation result was provided by oleic acid collector and the results of collector H602 were compared with those of collector oleic acid in the test. The test result of ore samples shows that at moderate pulp pH values (10.5-11.5) and other moderate technical conditions, the fluorite mineral can be obtained by new reagents and the rational reagents combination. The conclusion is 98%F of fluorite concentrate can be obtained, using the combination of H602 and S602 and only 5 steps in techniques. The paper discusses the mechanism of the flotation separation of fluorite mineral from intergrowth minerals."

Jan 1, 2003

By Lars Arne Granlund

Due to the coarse structure of mining explosives, one has to model a finite reaction zone,contrary to C-J calculations, describing their detonations, i.e they become dependent of diameter and confinement, An effort within the DYNO group has been to investigate if the DSD theory ( originally developed by Bdzil, Stewart / Los Alamos ) can be used to describe major groups of civil explosives.The groups of explosives tested are dynamite, anfo, aluminised emulsion, heavy anfo and straight emulsions.

Jan 1, 1995

By A. J. Davidson

A Cu-conducting solid electrolyte was used to develop the sensor. Instead of measuring the potential across the electrolyte from the reference material to the Cu-containing phase, a potential was applied and the stable current measured. This gave reasonable readings for copper-tin alloys, which agreed with the theoretical calculations, but was less satisfactory in the case of mattes because the surface area of electrolyte presented to the matte phase varied from sensor to sensor. To overcome this problem the potential was applied, the current was measured and then reversed and remeasured and the ratio of the currents was calculated. The current ratio is shown to be independent of the resistance of the electrolyte and the surface area of the electrolyte offered to the melt, but strongly dependent on the activity of the copper

Jun 21, 1905

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

It is possible to divide industrial minerals into four general categories: 1. fuels, 2. construction materials, 4. agricultural minerals, and 4. industrial minerals. It is proposed to ignore the fuels in the context of this paper and deal in general terms with the others. Mining companies have often considered getting into the industrial mineral business because they can see a resource development with good growth and consistent profits. However, many mining companies being conversant with the metallic side of the industry have spent sleepless nights determining which industrial minerals are most suited for their particular situation. Some have got into the business for the wrong reasons and wished they had never heard of it. Others have successfully adapted to the industrial minerals philosophy and now operate in both metallic and industrial mineral arenas. There is a large difference between firstly, the philosophy and secondly, the functions of being in the industrial minerals business as opposed to metallicÆs. The philosophies can be considered in parallel but it is necessary to clearly have an appreciation of the dominant influences that affect industrial minerals.

Jan 1, 1984

By Christoph Mueller

Mining operations today are characterized by a high degree of mechanization and single machine automation. However, their potential for cost cuttings and increase of productivity in the future is quite limited. Enabled by newest IT and networking technology, the operation of underground mines more and more can be seen from a process related point of view: Standardized Ethernet and Wireless LAN are the basis for a seamless and unified communication backbones providing an integrated infrastructure for data, telephony and video. All the components are available as off-the-shelf devices leading to an excellent cost efficiency. Basing on this standardized infrastructure, the equipment is able to become part of the infrastructure. To enable machines to be integrated smoothly into IT networks, the machine also has to have enhanced networking capabilities. This results in a new system architecture for the on board machine electronics separating real time control from IT and networking level functionality which can be implemented by a Machine Server. This machine server communicates with all kinds of above ground systems using mainly standardized formats like html or the IREDES standard. This information is made available mainly in 3D mine visualization tools. The paper explains this technology and shows implementations by two working examples.

May 1, 2006

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By V Poizat

In different parts of the world the term epithermal is commonly used for a variety of deposit styles. Using the redox state of the ore-forming fluid (inferred from mineralogy and alteration), the metal assemblage of deposits, and other characteristics, at least five different styles of epithermal deposit can be distinguished. Most of these different deposit styles appear to be related to magmatic fluids, with differences resulting from different compositions of source magmas. The most common style of epithermal deposit (low-sulfidation gold-silver deposits associated with calc-alkaline volcanic rocks) remains the most difficult to explain; the metals in these deposits may be derived by basement leaching without magmatic input, or they may come from magmatic volatiles, with contaminated I-type or S-type magmas as the most likely source.

Jan 1, 1995

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By G. R. Smith

Critical and strategic metals are often present in small quantities in low-grade domestic ores. When these ores are leached, the resulting solution usually contains the metals in very dilute quantities. Selective electrowinning from dilute electrolytes was investigated by the Bureau of Mines. A metal deposit containing 84 pct nickel was electrowon from the leach solution of a complex domestic ore bulk flotation concentrate originally containing approximately 2 wt-pct nickel. Key to achieving accelerated deposition rates, in the case of dilute solutions, is the rapid movement of the electrolyte through the electrowinning cell. Pure, synthetic nickel electrolytes were used to establish deposition parameters, and to optimize electrolyte velocity or mass transfer rates. Hydrodynamic and electrodeposition parameters for both the synthetic and leach electrolytes are presented and the experimental research described. Selective electrowinning appears to offer a viable alternative to physical separation methods to obtain separate metal "concentrates" from low-grade ores.

Jan 1, 1983

By Jim Truskoski, Alain Bouchard, Andy Kerr, Germain Labonté, Jim Barrett

"Improving mill grade recovery relationships is always good business. INCO’s Clarabelle Mill has just undergone a $16 million process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as INCO embarks on its second century of operation.INTRODUCTIONIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at INCO’s Clarabelle Mill in Copper Cliff, Ontario.BACKGROUNDThe Clarabelle Mill was built in 1971 on the southern rim of the Sudbury basin. At that time it was one of four mills operated by INCO in the Sudbury area. During the 1970’s, 80’s and 90’s, the need for increased process efficiency, higher levels of sulphur rejection to tails and the concurrent development of high capacity mills and flotation cells, resulted in the consolidation of INCO’s Sudbury area milling operations into a single, expanded facility at Clarabelle."

Jan 1, 2003

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By S. H. Ash

Introduction Probably the newest thing in mining safety is the apparent dissatisfaction on the part of the mineral industry, as represented by both management and labour, and the general public of many nations in which mining is conducted, with the safety record of the mining industry. This is reflected by published comments in the technical press;' in labour periodicals, in popular Journals and periodicals, and in the daily press (5, 11). Despite what may be said to the contrary, mining in the United States is becoming safer, and this trend has been evident for several years (see Figures 1 to 4). Because the author's experience has been mostly in the United States this paper will discuss briefly some recent observations in the United States that have a bearing on mining safety. Because coal mining is of primary interest to the Mining Society of Nova Scotia, the paper treats mostly of coal-mining safety; however, many hazards in mining .are common to all mines, regardless of the minerals mined.

Jan 1, 1950