Search Documents

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By B Mobilio, M Secheny, J Rachocki, G B. Sharrock, A Jäger, J L. Lett, I Brunton, G W. Capes

Establishment of the Cadia East Panel Cave Stage One (PC1S1) commenced with the firing of the first bell in early 2011. Production began with the completion of the undercut in May 2014. PC1S1 used a post-undercut composed of 114 drawbells covering a footprint area of 73 438 m². The extraction level is located at a depth of 1200 m below the surface and is based on a 32 × 20 m El Teniente layout. Cave establishment required the construction of multiple conveyor drifts, a large-capacity jaw-gyratory crusher and ancillary ventilation and pumping infrastructure. Preconditioning via hydraulic fracturing and blasting was implemented at various locations of the cave block height. This paper presents an overview of the key learnings from the commencement of undercutting to surface breakthrough, including rock mass classification and modelling, stress measurements, preconditioning, numerical modelling and cave monitoring.CITATION:Lett, J L, Brunton, I, Capes, G W, Jäger, A, Mobilio, B, Rachocki, J, Sharrock, G B and Secheny, M, 2016. Undercutting to surface breakthrough – Cadia East panel cave (stage 1), in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 65–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A T. Job, M L. Edgar, P R. McAree

Characterising ores in-pit and in real-time presents a significant value opportunity for the mining industry. Hyperspectral imaging systems are proposed as an enabling technology to achieve this real-time characterisation. This paper considers the application of a hyperspectral imaging spectrometer mounted on a shovel. We define the performance requirements for such a spectrometer and associated subsystems during a typical dig-load cycle. The relatively high swing rotation speed of the shovel requires approximately video-rate exposure times to achieve good spatial resolution. We analyse a selection of components against these requirements and find that suitable commercial spectrometers, detectors and optics appear fit-for-purpose. Automated, real-time spectral classification systems are also available, with only relatively modest requirements for processing power. The paper argues that at near peak solar illumination, a system for field deployment at the required sensitivity is viable using only commercial off-the-shelf components.CITATION:Job, A T, Edgar, M L and McAree, P R, 2017. Real-time shovel-mounted coal or ore sensing, in Proceedings Iron Ore 2017, pp 397–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Declining metal prices over the last few years have reduced the number of new metallurgical plants being built and limited opportunities for introducing new processes. However, technological advances are still being made. With increasing economic pressures, the emphasis is now on reducing unit costs by making equipment larger and through use of technologies with lower operating costs. This trend can be seen in the increasing size of grinding mills and flotation cells used in recent plant designs and in the adoption of HPGR crushing as an alternative to SAG milling. Few new technologies achieve widespread introduction until there are clear economic or operational drivers. These might currently include: ò          increasingly stringent environmental standards; ò          availability of exotic materials for equipment construction; ò          increasingly sophisticated instrumentation and control systems; ò          the need to treat increasingly refractory oretypes; and ò          the length of supply routes to many new plants. As a result of these drivers, a number of new and revitalised technologies will get increasing prominence in the design of new operations, such as: ò          use of ultrafine milling equipment such as MIM's Isamill for treatment of refractory gold ore concentrates; ò          use of thiourea as an alternative for cyanide in sensitive locations; ò          novel hydrometallurgical routes for treating base metal ores in remote locations; ò          paste thickening for tailings deposition; and intensive cyanidation of gravity concentrate

Jan 1, 2000

By S. B. Johnson

Keywords: Spray, Aluminum, Simulation A stochastic, droplet-resolved model has been developed to describe the behavior of a binary aluminum alloy spray during the spray-rolling process. In this process, a molten aluminum alloy is atomized and the resulting spray is deposited on the rolls of a twin-roll caster to produce aluminum strip. The one-way coupled spray model allows the prediction of spray characteristics such as enthalpy and solid fraction, and their distribution between the nozzle and the deposition surface. This paper outlines the model development and compares the predicted spray dynamics to PDI measurements performed in a controlled configuration. Predicted and measured droplet velocity and size distributions are presented for two points along the spray centerline along with predicted spray averaged specific enthalpy and solid fraction curves.

Jan 1, 2005

By Marlyn King, Kevin Peterson

Power Decks are voids created in the bottom of the borehole through the use of a suspended Super Plug. Explosive energy is started downward at initiation creating high pressures which find relief at the comers of the borehole cylinder in the bottom of the hole. This relief creates a horizontal break to the neighboring boreholes - the same effect as presplitting. This “presplit” represents a change of mass to.the explosive energy,and it is reflected upward in the more efficient form of tensile waves. This provides better use of the explosive energy than compression waves. This technique has created a new way of looking at the ways that explosive energy is transported through the rock mass.

Jan 1, 2002

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018

By T Harding, T Riggs, D Taylor

High-grade hematite ores in the Hamersley Province of Western Australia are associated with hydrothermal magnetite-apatite and magnetite-hematite-carbonate-apatite proto ores below the modern weathering surface. In addition, hydrothermal alteration of country rocks, once believed to be absent, is now recognised widely in shales and dolerites up to several hundreds of metres away from the ores. Both observations appear to exclude a simple supergene model for ugrading the host iron formations to high-grade hematite ore. Similar hydrothermal proto ores and country rock alteration are now being recognised in other high-grade hematite deposits worldwide, or have been recognised in the past.

Jan 1, 2002

By Steven J. Knoll, Theodore J. Williams, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 18 and 40 m, and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By Harold A. Watson

A method for measuring leakage of vapors into a chemical-cartridge half-mask facepiece during simulated use is described. The respirator, fitted with high efficiency cartridges, is worn in a dichlorodifluoromethane (CC12F2)--air test mixture while a series of timed activities (facial movements, varied breathing, exercise, etc.) is performed. Complementing other tightness tests, this method is useful particularly for studying face fit and the effect of facial movements on leakage. The concentration of CC12F2 within the facepiece is monitored continuously to observe the immediate effect of physical activity on leakage. A composite sample is collected simultaneously in a plastic bag as a measure of average leakage during the 18-minute test period. Leakage, reported as percent, is calculated from the concentrations of CC12F2 within the facepiece and in the test atmosphere.

Jan 1, 1970

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004