Search Documents

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

At present, discounted cash flow analysis is generally accepted as the preferred method of valuation of mine projects in surface coal mining. One of the major reasons for that is its ability to take into account the time effect of money over the life-of-mine. As a looking-forward method, it requires forecasts be made with regard to economic, technological, technical, geological, and environmental conditions that will prevail in the future. All forecasts are inherently uncertain as they are a function of the uncertainty of all variables of the discounted cash flows analysis. This indicates that the only alternative for modeling the uncertainty in the project evaluation is the development of adequate risk models to serve the decision-making process. The paper offers a model of project cash flows at risk in strip coal mining, which is an integrated corporate risk management solution. The model is based on a stochastic approach that provides the answer to the question about how large is the deviation between stochastic cash flows and the planned value (or that used in the budget) at each time step of the discounted cash flows analysis, that is due to the uncertainty in the model variables. A solution is worked out for the allowable range of the stochastic cash flows variation that determines the probability of achieving the planned value of a mine project. The Monte Carlo simulation technique is used to model the stochastic behavior of the project variables. A case study of an opencast coal mine project is provided to illustrate the applicability of the risk model. The results obtained provide a new understanding of the mine project risk as a component of the project discount rate.

Jan 1, 2006

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By Frank Cappuccitti, Stephen Chryssoulis, Stamen Dimov

Surface organic microanalysis of platinum (Pt) and palladium (Pd) minerals by TOF MS1 is an attractive complement and potential alternative to conventional collector screening methods. Its attractiveness lies on its ability to focus on individual Pt and Pd mineral particulates, therefore providing a more targeted approach. The only requirement is knowledge of the occurrence (mineral composition, grain size and association) of Pt/Pd in the feed sample. This newly developed technique can detect, and identify collectors and quantitate loadings on individual Pt/Pd mineral particulates at plant concentration levels. Using this technology, collector loadings were measured on Pt and Pd metal plates and on PtS2 and PdS particulates which had been exposed together to aqueous solutions of different collectors. Thus, data were obtained on collector selectivity, the effect of sulphur; and of depressants, the latter in combination with TOF-LIMS2 results. Staged rougher tests on North American and UG-2 ores linked Pt/Pd flotation kinetics with collector loadings and ultimately grade/recovery.

Jan 1, 2003

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By M. Arias

"An attractive foreign investment legislation, an anti-mining framework in the jurisdiction where a head office is located, the geographical location of the mineral resources, a country that offers the technology needed by the industry for its operations -- these are some of the many factors that make mining and mineral exploration a global business. It is precisely in the complexity of this new era of globalization and market environment, that sustainability initiatives are challenged. Responsible management of mineral exploration and mining is no longer defined by the use of efficient technology and resource management. Sustainability is not only a report compliance exercise or a green revolution. Sustainability is like any business, a long term profitable proposition. This new approach encompasses four pillars: social, economic, environment, and culture. This new approach connects humans and corporations; it is the way to engage, respect and improve relations with the people with whom we work and our neighbours."

Jan 1, 2011

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

Prominent among the ore minerals at Mt. Ellison, in the Brock's Creek district, Northern Territory, are a number of copper-bismuth sulphides wittichenite, aikinite, emplectite, in association with nativebismuth, chalcopyrite, bornite, chalcocite, sphalerite and linnaeite.Linnaeite and aikinite formed first and were followed by native bismuth. Wittichenite was later and substantially replaces earlier minerals. Replacement of aikinite by wittichenite has produced secondaryor reaction bismuth.INTRODUCTIONThe Brock's Creek district of the Northern Territory lies to the south east of Darwin and has been the locale of intermittent mining of small but rich deposits of diverse ore type. Gold, tin, and copper ores were recovered especially between 1890 and 1910 with minor exploitation up to the present time. Copper ores were of prior importance, the main production coming from supergene enriched deposits of chalcocite.The mines are situated in strongly folded Precambrian strata comprising slates, sandstones, volcanics and amphibolites with replaced haematitic rocks (Sullivan, 1953). The strata in the Brock's Creek area immediately north of the Darwin-Birdum railway line are domed around a roughly circular granitic mass some 5 miles in diameter. The Mount Ellison mine is located near the N.E. margin of the granite in metamorphosed basic country rock.Study of a series of polished sections from Mt. Ellison revealed the presence of linnaeite, chalcopyrite, bornite, aikinite, wittichenite, emplectite, bismuth, sphalerite, and chalcocite. With the exception of sphalerite and emplectite each of these minerals is prominently developed and intimately intergrown with the other constituents.

Jan 1, 1963

By José Cayetano

El presente trabajo plantea un proceso para minimizar el contenido de bismuto en las celdas de electrorefinación, a través de la adición de carbonato de bario a la solución electrolito, de forma que el bismuto soluble presente en fase líquida, se precipite sobre la superficie del precipitado insoluble de BaSO4, bajo una coprecipitación por adsorción e intercambio debido al equilibrio dinámico entre el precipitado y la solución de electrolito conteniendo al bismuto. En este sentido, se reduce la presencia del bismuto en el electrolito de cobre en un 75%, adicionalmente se tiene la disminución del contenido de plomo en un 96%, de estaño en 48% y de plata en un 18% aproximadamente.

Oct 21, 2015

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By David J. Lowell

The gold content of porphyry copper deposits ranges from less than 0.05 g/t to more than I g/t ((0.0017 to 0.035 oz per st) and the average is about 0.05 g/t (0.0017 oz per st) gold. Perhaps the highest grade mineralization found near a porphyry cop¬per deposit is the Ok Tedi Gold Cap ore body whose grade falls in the 2 to 3 g/t (0.07 to 0.1 oz per st) range. It is difficult to define a gold-rich por¬phyry copper deposit. All porphyry copper ore bodies contain some gold, but there seems to be a fairly sharp break in the gold content at about 0.1 g/t (0.003 oz per st) gold. There is also a problem in identifying dis¬seminated gold deposits that may have an indirect relationship to porphyry copper systems. This relationship is clear cut in deposits such as the Ok Tedi Gold Cap, the El Hueso deposit, the Fortitude and West de¬posits at Battle Mountain, NV, and the Sur¬prise deposit at Ely, NV. There are many other bulk disseminated, epithermal-type gold deposits - McCoy, NV, for example - that might be related to a porphyry system but where this relationship is remains very uncertain. In such places as the Goldfields and Tonapah district in Ne¬vada and in the El Indio, Chile district, there may be a vertically stacked ore deposit rela¬tionship between near surface epithermal deposits and disseminated molybdenite and chalcopyrite enargite mineralization at depth that may represent a deep porphyry system. This, however, has not been positively demonstrated. Most of the bulk epithermal gold deposits are probably not related to porphyry copper systems. Exceptions would probably be Ok Tedi, El Indio, El Hueso, Battle Mountain, and Lepanto where vertical or lateral zoning relationships are more apparent. This author believes that porphyry copper systems are related to a relatively unique type of intrusion that is probably distinct from, for example, the McCoy intrusivebody. For that reason, deposits such as McCoy, Chimney Creek, and the like will not be included in the definition of gold-rich por¬phyry copper deposits for this article. The interpretation of the origin of several of the deposits previously mentioned are subject to an unusual amount of contro¬versy. For example, geologists seem to be equally divided about the presence of a porphyry copper deposit below the El Indio deposit. Geologic setting Continental vs. island arc Several geologists have speculated that the gold-rich, moly-poor, porphyries are

Jan 1, 1989

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United Status. These data are presented in tabular form under the following headings; General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

By Malcolm Mudge

"One of the oldest mining areas in the World exist in Africa and the Middle East. This area is being exploited by foreign and local mining entities. Several large plants, both foreign and local as well as small operators, conduct their mining business on a scale which would be could be prohibited in any other part of the world. Relatively recent European disaster with tailing disposal and breakout has highlighted the problem.More important to the author is that the presence of foreign entities in zones which have not remedied the situation but has heightened the concern due to those entities using similar outrageous methods in treatment of waste. The abject misuse of technology cannot be permitted to continue and the lack of any metallurgical knowledge in the treatment of gold ores is considered deplorable for the majority of third world countries.The destruction of cyanide is simple and straightforward and requires no special skills. In South America, we developed a system that is modular, compact and can be operated in batch mode to cater for several clients, as required. Larger installations would require a separate module, as treatmentwould be on a continuous basis."

Jan 1, 2003

Effective tools are not only essential for the design of practical and efficient underground mine ventilation systems but must also play an integral part in the operation of the mine. One such tool is VUMA-coal ventilation simulation software. VUMA-coal is Windows-based and has been specially designed for the simulation of underground coal mines and includes user-friendly coal specific interfaces and three-dimensional graphics designed to facilitate in the construction and analysis of networks. VUMA-coal can be utilised during the design phase of new collieries, be used to conduct ?what-if? and optimisation studies, and be integrated into the ?day-to-day? ventilation related operations. In addition, VUMA-coal can be used to simulate dust and gas distribution in a ventilation network, as well as predict the impact of control measures. This paper describes the interactive VUMA-coal ventilation simulation software and its underlying design features and outlines a case study of how VUMA-coal has been integrated into Anglo Coal?s Ventilation and Occupational Hygiene Engineering [VOHE] department as part of the standard planning and evaluation process in their operational mines as well as long term planning and future mining operations.

Jan 1, 2009

By A E. Annels, I P. Hodkinson an, S P. Barr

Narrow vein systems represent an important source of gold, which have generally been exploited by small to medium sized companies. Their evaluation poses particular problems because of their grade and geological complexities. The determination of grade is arguably the most important activity in resource estimation, as it is generally grade and not tonnage that makes an orebody. This is particularly true of narrow vein-gold deposits whose resources are generally relatively small, though medium to high-grade (6 - 40+ g/t). They often display extreme grade anisotropy in all directions. Two grade populations are generally observed; 1) low, often subeconomic, background grades and 2) high-grades associated with discrete ore shoots. It is possible for gold to be distributed within the wallrocks as well as within the vein. Extremely high-grade values typify this style of mineralisation and require special consideration during grade estimation to determine if top cutting is valid or not. Estimation of both width and accumulation in 2D on vertical longitudinal projections or inclined planes have historically been used to evaluate narrow veins. Resource estimates based on traditional 2D methods is still widespread, but has in some cases been replaced by computer-based 3D modelling. Grade estimation methods are well-known, ranging from classical to geostatistical. Historically, classical methods such as inverse distance weighting have been used, though geostatistical indicator kriging methods are sometimes applicable. Geostatistical studies are driven by the production of reliable variograms, which in narrow gold veins is often problematic. It is generally difficult to define resources from drillhole intersections beyond the inferred and indicated categories with any confidence. In the majority of cases underground development is required to define measured resources and ore reserves. Trial mining/bulk sampling is often used to test estimated grades and also provides important data on ground conditions and the parameters relating to the proposed mining method required for ore reserve definition. Regular reconciliation should be undertaken between the estimated stope grades, grades indicated from stope/truck sampling and grades realised in the mill in order to determine whether correct evaluation strategies are being applied. The important feature of narrow vein-gold deposits is their strong geological controls; in response to this, geologists must understand the geology as best as possible.

Jan 1, 1999