Search Documents

By Khaled Morsy

The tragic incidents at Sago and Darby coal mines in 2006 pointed out the need for stronger seals to resist the blast effects of violent gob explosions. Mine Safety and Health Administration (MSHA) has published the final rule on Sealing of Abandoned Areas in April 2008. According to the final rule, the mine seals for unmonitored gob areas should withstand an instantaneous pressure of 120 psi. Reinforced concrete (RC) seal is one of the feasible options that can be used to meet the final rule. Concrete is a heterogeneous, cohesive-frictional material and exhibits complex non-linear inelastic behavior under multi-axial state of stress. The increased use of concrete as primary structural material requires the development of sophisticated material models to have an accurate prediction of the material response to a variety of loading situations. The constitutive modeling of concrete has advanced considerably in the past three decades. Choosing a reasonable concrete material model is important in order to obtain an accurate mine seal design. This paper attempts to address the effect of different concrete material models on the response of RC seal subjected to dynamic loads from methane explosion. Three concrete models, from ABAQUS library, were selected to address the effect of non-linear behavior of concrete and damages due to tensile and compressive stresses. In addition, a typical and verified concrete material model was used for conducting 3D finite element models simulating the RC seal by ABAQUS, EXPLICIT ver. 6.6.

Jan 1, 2008

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By R. F. Favreau, P. Favreau

Rock excavation is the first process in the cycle of operation of a mine, and efficient blasting is paramount to the profitability of the mine. The traditional way to design blasts has been by trial and error, based on the experience of the designer. This is probably the only important engineering practice which continues to be done without a precise engineering technique. The efficiency of most other mine processes has been improved by the use of high-tech, while a majority of blast design has not yet profited from the advantages of the computer. However, with the advent of the high-tech blast simulator Blaspa, it has become possible to design the parameters of the blast according to normal engineering practices. Over the last 50 years, the chemical and physical mechanisms which occur during a blast have come to be identified; they are reviewed in section B. Although these mechanisms are complex, they have nevertheless been expressed in terms of mathematical equations which have been assembled together in the computer to create the blast model Blaspa.

Jan 1, 2002

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By J. Crummy, I. K. Anderson, A. J. Hall, R. S. Haszeldine

Bedrock gold mineralisation has been located in association with an extensive float train 25 km west of known alluvial gold. It is in the form of open, matrix-supported breccias comprising pyritic quartz/sericite clasts in a vuggy, cherty chalcedonic and crystalline quartz matrix. Fluid inclusions in pyritic clasts indicate trapping temperatures for gold mineralising hydrothermal fluid of 170-240 degrees C. This mineralisation could represent the upper part of a feeder zone to an exhalative hydrothermal system. It is possible that other high-level feeder zones could be preserved elsewhere in the area. Deep weathering of such a system could provide a source for the alluvial gold localities near Helmsdale. It is suggested that east and central Sutherland presents good prospects for exhalative epithermal gold mineralisation and the associated feeder zones

Jun 19, 1905

By C. R. Carpenter

A dynamic gas-mixing system assembled by the Bureau of Mines for the generation of precise gas mixtures from sources of concentrated or pure gases and diluent gases is described. A set of electronic mass flow controllers with maximum flows ranging from 10 to 5,000 ml/min, a so-called Pure Air Generator, and gases in cylinders are used to generate differing gas concentrations. The repeatability of the delivery rate of a flow controller, measured on different days, has a precision of 0.3 pct of the setting. This dynamic gas-mixing system reduces the cylinder inventory and the demurrage charges for special gas mixtures. Gas mixtures that cannot be shipped commercially, such as flammable mixtures of methane in air, can be conveniently prepared by this system. The maximum dilution ratio is 2.5 x 104. Thus, gas mixtures can be made over a wide range of concentrations, from the percent region (by dilution of a pure single-component gas) to fractional parts per million (by dilution of a premixed standard, e.g., a 1,000-ppm mixture). This system is especially useful in determining the response of gas detection devices over the entire range of their measurement. Because the controllers are voltage controlled they lend themselves easily to automated control using computer-based systems.

Jan 1, 1983

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from 4.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004

By M. Kahn

This paper traces the rise of South Africa's mining industry in the context of the different state forms that oversaw its development. It commences with the mining-led industrial revolution through four periods of conflict, each of which contributed to a deepening of the industrial base, with constant battles between domestic and foreign capital and labour, and the rise of both Afrikaner and African nationalism. The role of state-owned enterprises has been crucial in shaping this dynamic so that at its peak the public sector and leading mining houses constituted two massive centres of power. This was followed by a thirty-year period of neo-liberal experimentation. The current debate on the 'developmental state' is an attempt to reconstruct the state as a counterweight to capital. It is argued that while the country has moved toward inclusive political and economic institutions, these are both limited by deep 'extractive' characteristics. This transformation failure provides a fertile ground for populism that presents one of the biggest threats to inclusive growth. Cited examples point to the many ways that states have sought to deal with the bonanza that conversion of mineral non-resources into resources brings. Such greenfield resources on state land, or in areas where the state holds monopoly rights, do not present ownership issues. It is suggested that this is the route that South Africa should follow, as the alternative will be conflictual.

Jan 1, 2013

By Louis Schaffer

This report characterizes several coal Dine mobile equipment operator populations with respect to age, mine experience, machine operator experience, and training. The information is used to demonstrate a method of normalizing the injury data collected by the Mining Enforcement and Safety Administration-Health and Safety Analysis Center.

Jan 1, 1977

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Pradip, Beena Rai

A molecular modeling study was carried out on an adsorbed oleate monolayer on the surfaces of three calcium minerals, fluorite, calcite and fluorapatite using Universal Force Field (UFF) potentials. The cleavage plane of calcite {104} was the best template for oleate monolayer adsorbed since the surface structure enabled all the calcium sites available on the surface to be occupied by oleate anions. The area occupied per chain of oleate in this well packed monolayer was computed to be 20.2 Å, which exactly matches the value calculated to be the parking area per oleate molecule for a fully packed monolayer based on strictly geometric calculations. On the other hand, the precentage of calcium sites occupied by oleate to achieve a fully packed monolayer in case of fluroite and and fluorapatite was found to be 67% and 75% respectively. The results of this theoretical study suggest that while all the three adsorption conformations, that is unidentate, bidentate and bridging type are equally likely on fluorite and fluorapatite, bridging is most likely on calcite. Interestingly, all the conformations are observed experimentally for calcite-oleate system also. The reasons for this discrepancy between the theoretical predictions and experimental observations are not clear. More work is required to resolve this discrepancy, in particular simulation studies in presence of solvent water molecules on the surface.

Jan 1, 2003

By William N. Patterson

Drive systems for mining machines are usually sized to accommodate anticipated peak loads. Usually, the average power requirements are considerably less. Energy storage and power averaging are attractive concepts for mining machinery and could have far-reaching implications. The purpose of this program was to: ? Identify truly feasible concepts, ? Identify advantages/disadvantages, limitations, and constraints, ? Evaluate feasibility based on today?s technology, ? Identify anticipated safety problems, and ? Provide the designer with a comprehensive literature base. Concepts evaluated include flywheels, high energy batteries, gas charged accumulators, inductive storage, capacitive storage, springs and counterweights, thermal, closed cycles, internal combustion engines, trolley systems, and hybrid systems. A comprehensive reference index is provided. Included is an appendix containing abstracts of the pertinent literature.

Jan 1, 1980

By R. A. Halatchev

A risk model for assessment of the uncertainty in the forecasts of the planned profit is developed. It is based on the selling price of the metal recovered from the ore and the production per shift of the excavators. These two critical variables characterise the economic and technical aspects of the mining venture. Time-series methodology is used to describe the behaviour of the economic variable, which improves the adequacy of the modelling. A hypothetical open-pit gold mine is used to illustrate the application of the model. Results obtained show that the model is a good alternative to sensitivity analysis in taking account of the stochastic character of the price of the metal recovered from the excavated ore and the production per shift of the excavators used. The model can be extended by the inclusion of new variables that have a probabilistic nature

Dec 1, 1996

By André de Jager, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge. The mine has installed a technologically advanced seismic monitoring system with monitoring sensors positioned at various locations and depths throughout the pit. The electronic data recording system records all relevant information on a continuous basis with early warning signals in cases of potential danger. From the information recorded by this micro-seismic system it was established that the energy release into the high-wall is predominantly influenced by the mining rate, water content and mining tempo and to a lesser extent by the blasting operations. To limit the negative effects of blast vibrations, the use of Electronic Delay Detonators (EDDs) was introduced. The optimal delays were determined through signature trace analysis. The vibrations obtained during blasts initiated by means of electronic delay detonators were monitored and compared to those traditionally obtained when standard pyrotechnic delay detonators had been used. The measured vibration data indicated an improvement of 25% to 100% drop in vibration amplitude compared. The accuracy and programmability of EDDs presented huge potential for blast optimization in terms of limiting the vibrations without compromising fragmentation. The whole project was conducted over a twelve week period with some 4000 EDDs. The average size of a blast was in the order of 350 holes using about 40kg explosives per hole, which equates to 14,000 kg explosives over 12 different blasts. The paper deals in detail with the blast optimization process with regard to: - determining the rock response time; - establishing the signature traces; - analyzing the wave interference patterns; - predicting the direction of constructive and destructive wave interferences; - optimizing of the inter-hole and inter-row delay periods; - measuring the ground vibrations. The results obtained during electronic blasting are compared to those obtained during pyrotechnic blasting. Comparisons are being made with regard to the following: - ground vibration measurements; - pit wall stability measurements; - blast safety.

Jan 1, 2006

By Martin C. Jones

This paper outlines the development of small diameter grouted piling, to deal with foundation problems in difficult soils conditions and in very restricted access areas. A number of applications are outlined to show the way in which these piles have been used over the last sixteen years in Canada. PICKERING GENERATING STATION - ONTARIO HYDRO UNDERPINNING OF SCREENHOUSE - TRASH DISPOSAL AREAS Between 12th July and 29th September 1971, 40 small diameter grouted piles were installed in the screenhouse at Pickering Generating Station. Access was extremely restricted as the screenhouse had been completed and the majority of mechanical equipment had been installed. The two ends of the screenhouse had been built on granular fill which overlies till and shale bedrock and settlements had been observed which it was decided had to be halted even though the rate of subsidence had decreased. Two diamond drills were employed to install 8 inch

Jan 1, 1987

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978