Search Documents

By I. R. Muirhead, S. Frimpong

"The mechanization of mining operations in underground coal mines has led to faster cutting rates of coalfaces with increased levels of emission of gaseous and particulate contaminants in the workings. Consequently, the fresh air streams from the main ventilation systems reaching distant workings are often insufficient, ineffective or inadequate and have to be supplemented by auxiliary ventilation systems to create and maintain the required working environments underground. The efficiencies of auxiliary ventilation systems are largely affected by drivers of the system such as the type and capacity of the fan; the type, length, diameter and condition of the ventilation ducting and the distance from the discharge end of the intake ducting to the face. Traditionally, single point measurements of methane gas concentrations using either flame safety lamps or hand-held measuring instruments have been used to assess how safe underground coal workings were. Unfortunately, such occasional measurements of methane gas concentrations do not give an accurate picture of the real gas concentration in the working as they are often taken from the easily accessible locations in working. Continuous monitoring of the methane gas concentration in development headings enables a better assessment of the environmental conditions prevailing there. All variations in the methane concentrations are more easily captured on a continuous monitoring basis than by instantaneous single point measurements. The approach adopted in this work was to continuously monitor the concentration of methane very close to the face and about 60 m outbye in development headings, observe the types of auxiliary ventilation equipment and their sizes being used in the working as well as noting the lengths from the discharge ends of the forcing and exhaust ductings to the face.In this paper, empirical methods are used to calculate the mean efficiencies of the auxiliary ventilation systems in selected development headings in coal mines in North America. This enables the assessment of the effectiveness of the auxiliary ventilation systems and the identification of the system drivers in them. The results show that the efficiencies of the forcing systems ranged from 17.02% to 96.81% while the efficiencies of the overall systems varied from 6.04% to 54.16%. The distance from the discharge end of the intake ducting to the face appeared to be the strongest driver in the performance of the auxiliary ventilation systems studied. It was also noted that when the discharge end of the intake ducting to the face does not exceed 7 m, there were faster purging rates of methane at the face and the efficiencies of the overall auxiliary ventilation system were greater than 50%. These findings are very important in underground coal mining in North America as they will assist to avert calamities, such as the Westray coal mine disaster in 1992 which resulted from the explosion of methane gas, by identifying which components of the ventilation system need special attention to create safe working conditions underground."

Jan 1, 2003

By Eduardo Macedo Junior

O presente trabalho descreve o desenvolvimento de uma nova especificação para a Linha de zincagem numero 3 (LZC#3) da Companhia siderúrgica nacional (CSN), de grande demanda e aceitação, alta produtividade e foco nos requisitos do cliente que tangem qualidade superficial e características metalúrgicas (resistência mecânica) em aços para atendimento do mercado Norte-americano. Este novo produto tem como característica o ciclo de recozimento com velocidade alta para obtenção de microestrutura 100% encruada na saída do equipamento e limites de escoamento e resistência acima de 500 MPa. A combinação dessas características do produto junto com as características do processo tornou a especificação “ASTM-A653MSS80CL1” um grande desafio para garantir qualidade superficial sem comprometer as propriedades mecânicas especificadas assim como a integridade do equipamento. O baixo custo de produção associado a alta produtividade desse produto fazem da especificação “ASTM-A653M-SS80CL1” um produto de extrema importância para a estratégia adotada pela CSN, mantendo dessa maneira sua competitividade no mercado Norte-americano e garantindo capacidade máxima de produção do seu equipamento em tempos de retração do mercado interno.

Aug 17, 2017

By E. J. Murphy, A. P. Rowles, John C. Holtz

"INTRODUCTION The use of sheaths or hollow cylinders of flame-extinctive materials surrounding cartridges of permissible explosives has been developed during the last few years; the history of sheathed explosives in their salient development in Belgium was treated recently in a publication of the Bureau of Mines. 6/ This development is of great interest in explosives technology, for it holds possibilities of reducing further the ignition hazards that may cause many coal-mine disasters. The township interest in sheathed explosives in this country is attested by the passage of some State laws permitting the use of such explosives on shift 7/; inquiries are received in increasing numbers concerning the effects of sheaths on practical hazards as well as the general technology underlying their use."

May 1, 1943

By Ian McFeat-Smith

Despite a present, short-term economic recession, a remarkable enthusiasm exists in Hong Kong for building infrastructure including major tunnel projects. This paper provides details of current and recent bored tunnel works together with an insight into the impressive list of future underground projects planned by the MTRC,KCRC, Highways Department and Drainage Services Department for the next decade. Risks for each of these works including pipejacking, mixed face and rock tunnelling generally in Hong Kong are also identified. From this is evident that the scale and difficulty of such works continues to increase, requiring the use of more sophisticated methods of construction, the need for better methods of assessing and managing risks and for Government to utilize improved, more equitable Conditions of Contract for such major tunnelling projects.

Jan 1, 2001

By Jean Vavrek, Rob Barber

"What is CIM’s role on a planet-wide scale?That question has been coming back to the forefront of many discussions regularly in the months since we came on board as Executive Director and Vice- President International. CIM, by its name and by the nature of its history and make up, has mainly been a Canadian entity. It has been created by an act of Canadian Parliament and it is set up to work within the Canadian federal and provincial framework.Yet the name CIM is one well known and recognized for quality and professionalism worldwide. One could say that CIM has established a level of brand recognition that transcends it name and its origin. CIM has also evolved with the times, as the world has evolved and more so as the world of mining has evolved. So we stand today with a fairly large portion of our membership residing outside Canada and outside the United States. We also stand today looking back at the role CIM has played in events that we have been partners in organizing outside Canada; and for a long time CIM has provided insights into what is going on in the rest of the mining world by inviting authors and by featuring topics from around the globe.Today, Canada is still a leader in the mining industry. Canadian mining companies are involved in exploration and operations around the world. Canadian operations serve a good portion of the global demand of many metals and minerals, recently adding diamonds to the slate. Canadian expertise in various areas also makes Canada a good base for exporting a wide range of products and services around the world."

Jan 1, 2004

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By Robert B. Parsons

"Finance Minister Paul Martin's second budget might be good for Canada's mining industry in the long run, but the budget raises a number of concerns for the industry in the near term. The budget papers suggest that the 25% resource allowance is not working as intended, and report that the Department of Finance will be reviewing this valuable allowance. The so-called ""large corporations tax"" rate will be increased. This annual tax, which is imposed on a corporation's capital even when the corporation is not in production, is particularly harmful to the mining sector.IntroductionThe Honourable Paul Martin, in his second federal budget, emphasized spending cuts and made only modest tax changes. However, two of these tax changes could have a serious impact on the Canadian mining industry: the proposed review of the 25% resource allowance; and, the increase in the large corporations tax rate.Personal Tax Measures Personal Tax Rates UnchangedThe government has been under political pressure not to increase personal tax rates. Mr. Martin's announcement that rates would not change will be popular."

Jan 1, 1995

THE de-silverizing of base bullion at the Port Pirie works is carried out in accordance with the principles of the well-known Parkes process. The base bullion produced by the blast furnace department carries (apart from silver values) impurities, the chief of which are copper, antimony, and arsenic. In order to more clearly indicate the grade of the base bullion, the following analysis, representative of a half-year's production of base bullion, is submitted...Before proceeding with the actual operation of de-silverizing, it is necessary that the impurities, copper, antimony, and arsenic, should be eliminated. This is accomplished in the following steps :- (1) Removal of Coppel - Copper is largely present in the base bullion as dissolved sulphide, and this is removed by liquation in a reverberatory type furnace, of which the following are the essential details :-Working temperature 7500 to 8500 C.Coal consumption per 24 hours 2 tons.The hearth of the furnace is encased in a steel tank 22 ft. 4 in. long by 13 ft. 4 in. wide by 2 ft. 10 in. deep; the bottom of the tank is covered by a depth of composition conforming to the invert :-Cement 39 cwt.Brick dust 8.4 tons.Fireclay 0.6 tons.Sand 0.6 tons...

Jan 1, 1922

Prediction of fragmentation by blasting is most commonly based on theassumption that a single distribution of pre-existing discontinuities is present within a blasted rock volume and that the underlying mechanism of failure is tensile failure. It is assumed that the tensile stress field created by a blast initiates and extends radial cracks around the blastholes. Interaction between radial cracks from different blastholes and the free surface creates rock fragments. In reality, fragmentation of the rock occurs due to two mechanisms.One is related to the compressive-shear failure of the rock (mainly rock matrix) close to the blastholes, while the second mechanism is the previously mentioned tensile failure of the rock mass. The secondmechanism of failure occurs in the form of extension of the larger cracks in the region beyond the crushed rock, and this type of fragmentation occurs after the crushing phase. In the case of hard rock or blasting where the extent of crushing is minimal, the currently used prediction methods give a reasonably good result. However, there are many blasting conditions where the amount of rock crushing is significant. In the case where fragmentation of the given rock volume occurs dueto two different mechanisms, modeling of the rock fragmentation with a single distribution function is not appropriate. To model the fragment size distribution generated by two different mechanisms, it is necessary to use a two-component fragment size distribution function and a scaling parameter that will determine the proportion of the fragmented volume created by each mechanism. The purpose of this paper is to present results of blast fragmentation modeling based on two mechanisms of failure. The two-component model (TCM) utilises experimentally determined parameters from small scale blasting and parameters of the Kuz-Ram model, for more accurate prediction of the complete rock fragment size distribution curve. The methodology is such that it is possible to predict complete fragment size distribution, including fines, of ROM product for a future mine, at the feasibility phase of mine design.

Jan 1, 1999

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U. S. Department of the Interior, to stimulate greater interest in safety in the mineral-extractive industries and to encourage the development of more effective accident-prevention programs. Since its beginning in 1925, thirty-four safety contests have been conducted. This publication reports results of the 11 annual contests for the period 1948-1958, inclusive. Mineral operations awarded the "Sentinels of Safety" trophy for the best safety record in their competitive group as well as those ranking second, third, fourth, and fifth are listed along with a summary of their achievements in preventing disabling injuries. In addition, this publication contains statistical information reflecting the disabling work-injury experience of all other mines and quarries enrolled in the annual contests. The injury statistics of these operations are arranged in the six groups of the competition and through 1955 are the only data on injury-severity at noncoal mineral operations published by the Bureau of Hines. Recognition of the National Safety Competition in promoting safety has increased steadily during its 34 years. The number of plants participating in these annual competitions increased from 210 in 1925, its first year, to a record of 675 in 1958. The expanding scope of the National Safety Competition indicates that more mines and quarries in the United States are enrolling 90 all available means to promote safety on the job will be used. Safety contests like this are generally recognized, in the field of safety promotion, as an effective way to arouse and hold the interest of employees and officials in accident-prevention programs. They tend to forge individual precautionary acts into group action centered on a common objective, such as winning the ?Sentinels of Safety? trophy.

Jan 1, 1960

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in open-pit mines intensively expose the drill operators to whole-body vibration and shocks and thus to musculoskeletal disorders. The roles of an individual, machine, and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their role among 39 drill operators from Indian iron ore mines. It shows that 70% of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1. Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill machine model, rock’s hardness, uniaxial compressive strength, and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found that drill’s age, seat pad thickness, and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention to reduce and monitor the exposures and health risk.

By Clinton C. Knox

To demonstrate the feasibility of unwatering ore reserves previously indicated in the virgin Melrose zinc-lead field in Kansas and Oklahoma, the Bureau of Mines .carried through a pumping project on the Park Walton farm in 1943. Due to success of the undertaking, attention was turned to exploration of other indicated ore deposits and promising areas within that part of the field benefited by .the drainage project, By the middle of 1946, four private mining companies were active in the field; and a considerable output of lead and zinc concentrate had been obtained from the new Park Walton mine and mill. The Park Walton Ore deposit was unwatered by installing deep-well pumps in three holes previously drilled by the lessee. Pumping was continued by the Bureau of Mines at a rate of 2,500 to 1,000 g.p.m. for about 6 months; during this time the local static artesian water-level, originally averaging 108 feet below the surface in the old drill holes was lowered to the 316-foot level, which justified beginning the initial shaft sinking and mine developments. In all, about 750,000,000 gallons of water was pumped by the Bureau of Mines at an operating cost averaging $0.024 per 1,000 gallons.

Jan 1, 1948

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By L. R. Verney

A number of interrelated factors influence the economics of the sulphide smelting of copper, lead, zinc and nickel. This paper discusses these factors, mainly from a US point of view, and shows how they affect the cost of construction and operation of new and existing plants. The paper shows how metallurgical plant construction costs and the consumer price index have increased at a much faster rate than metal prices thereby making some metal mining and production operations within the USA, Canada and the EEC less profitable than operations elsewhere. This in turn inhibits new "grass roots" metallurgical developments. It is explained how retrofit of existing pyrometallurgical plants can be a more viable development than the construction of "green field" plants, especially if such retrofit improves, energy efficiencies, overall operating costs and reduces emissions of sulphur and other toxic wastes. Some aspects of metallurgical plant operation are examined, especially for copper and nickel, to show how changes in operating practices may develop in order to improve overall smelting economies, especially when developed in conjunction with objective retrofit. The paper also examines some financial aspects, especially insofar as the disparity between terms for loans offered to third world countries and the USA and the EEC are concerned and also comments upon the need, especially within the USA, for legislation to permit rapid depreciation of capital. Specific comments are made about environmental aspects, including the lack of uniformity of pollution control legislation and how environmental considerations may have some bearing of the location of future smelting operations.

Jan 1, 1983

By A. Sullivan

Success in mining demands the creative application of equipment, systems and processes to the unique needs of each mineral deposit, market and, though often overlooked, the culture of the individual business. In recent years, domestic coal mining companies have become more attentive to the contribution safety and loss control programs have on their financial results. Although most have adopted fairly conventional safety programs, some have created systems and processes tailored to their unique circumstances. While each coal mining business must consider the typical risks inherent to our industry, excellence in safety is most likely achieved when a safety program is customized to meet the needs of the individual business.

Jan 1, 2000

By Jane Spooner

"The papers presented in this edition of the Bulletin cover some of the business issues that face mining companies exploring or operating in jurisdictions outside Canada. While technical innovations may, generally, be seen as fast-moving and farreaching, these papers also show that changes in approach and thinking continue to be evaluated and implemented.The Forum paper co-authored by Roger Taplin of McCarthy Tétrault LLP and Marchand Snyman of Muratie Investments Pty Ltd. highlights the quite radical changes that have taken place in South Africa’s mining industry with the introduction of the Mineral and Petroleum Resources Development Act, 2002, in October of that year, together with the Broad-based Socio-Economic Empowerment Charter for the South African Mining Industry and the Mineral and Petroleum Royalty Bill of March 2003."

Jan 1, 2004

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018