Search Documents

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

The Bureau of Mines is active in programs pertaining to solid waste disposal and land reclamation. Nine reclamation projects of mining companies and six projects of the Commonwealth of Pennsylvania were investigated to provide information on the procedures, costs, and results obtained from reclamation projects of bituminous coal-waste disposal areas. Refuse disposal costs of mining companies ranged from 9 to 28 cents per ton-mile, and quantities disposed of ranged from 600 to 4,500 tons per day. Spreading and compacting the refuse at the dump site ranged from 3 to 20 cents per ton. Cost of covering with soil and planting ranged from $750 to $1,646 per acre. Total costs of reclamation for the Pennsylvania projects ranged from about $1,800 to more than $15,000 per acre. Refuse preparation costs ranged from $772 to $5,550 per acre. Soil covering and planting costs ranged from $1,083 to $5,086 per acre. The best results were obtained by soil preparation and conditioning prior to planting. The type and depth of soil and effect of climate were also factors.

Jan 1, 1973

By O. H. Metzger

This is one of a series of papers being published by the Bureau of Mines on mining areas and districts in the Western states. It describes mining and milling practices in the vicinity of Wickenburg in Maricopa and Yavapai Counties, Ariz. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of the operators of the mines visited. Reports of geologists and engineers who previously visited the area were drawn upon freely. Individual acknowledgments are made in the text.

Jan 1, 1938

By Sushil Bhandari, Amit Bhandari

Blast optimization in open-pit operations is a task that often remains at a theoretical stage. Indeed, when it comes to operational blast design and onsite implementation, time restrictions and field conditions make it difficult to execute a planned pattern accurately and optimization according to local conditions is even more difficult. For example, adjusting a drill pattern to a complex face geometry is not something that can be easily undertaken on site. Blasters and engineers will do their best trying to distribute boreholes over the bench and even then, it can take them hours to achieve an acceptable layout. Similar situations occur with delay sequences, when trying to adjust them to address selectivity or vibration issues. For these reasons, operational blast design will often remain at a very basic level and the required adjustments are laid aside due to the difficulty of implementing them on site.

Jan 1, 2019

By A R. Bye

Energy comes at great cost to our world and societies and therefore we should use it wisely and optimally. Societal pressure is enforcing this and the industry must respond by being proactive.The mine-to-mill approach to integrated mine and semi-autogenous grinding (SAG) mill optimisation demonstrated that throughput gains of up to 20 per cent could be obtained through a closer match of blasted run-of-mine ore to the feed best treated by a SAG mill. Since that approach was developed, new drivers have risen to prominence including environmental costs and impact of energy, water, waste. This is set against a backdrop of reducing ore grade and increasing demand that is pushing up our impact on the environment. The new challenges demand new approaches.This paper explores the opportunities in taking traditional approaches to optimisation to new levels of two-way integration and incorporating potentials for ore upgrade into circuit design. The new mantra may be æflexible circuitsÆ û designing and building for the present and the future by allowing for the uptake of new and future technology.

Jan 1, 2009

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named &apos;3D Incremental Analysis based Stope Optimization&apos; was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

By Justyna Swolkień, Nikodem Szlązak, Dariusz Obracaj

Polish coal mines are characterized by severe geological conditions and the co-occurrence of natural hazards. These hazards are associated with methane and dust emissions during mining processes which can provide methane, dust or methane-dust explosions. Besides, there are such natural hazards as gas and rock outbursts, rock bursts, spontaneous combustion of coal and environmental heat load. The mutual influences of various geological conditions, as well as the natural hazards, intensify the increase of the methane explosion hazard. The occurrence of methane explosions in the Polish mining industry between 2013 and 2108 are analyzed. Fatal accidents are compared with similar events in the global mining industry. The methods of preventing the explosion hazard as well as methane emission control in the Polish coal mining sector are presented. Methane hazard prevention should be adapted to levels and other natural hazards, especially those related to ventilation of underground mine. The methods of preventing methane emissions into mine excavations are often contrary to the means of preventing other ventilation-related hazards in the underground mine, e.g. the prevention of spontaneous combustion of coal in the goaf of longwall panel. Therefore, the design of longwall panels should be preceded by a detailed analysis of the results of both methane emission prediction and forecast of other ventilation-related hazards.

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005