Search Documents

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960's and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By Thomas Kuhn, Carsten Ruehlemann, Christina Heller, Anna Wegorzewski

The commercial extraction of metals from manganese nodules on an industrial scale requires more than 50% of the investment necessary to realize manganese nodule mining. This is mainly due to the fact that a completely new metallurgical processing scheme for the extraction of both base metals (Ni, Cu, Co) and high-tech metals (Mo, Li, Ga) has to be developed and upgraded to industrial scale. There are a number of conventional processing technologies that combine hydro- and pyro-metallurgical approaches such as the INCO and CUPRION processes which have been developed in the 1970s and 1980s. Today, new approaches based on selective leaching with chelating agents and bioleaching try to minimize energy consumption and waste production. All of these extraction methods require knowledge how the metals are structurally bound in the manganese oxides. In this contribution we will review the current knowledge about the mineralogy of iron and manganese minerals in the different marine oxide deposits, present our results, and discuss the possible consequences for metal extraction.

Sep 1, 2014

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of “but which formula is the right one?” The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: • Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) • Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) • Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state&apos;s transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330&apos; to 528&apos; in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6&apos; diameter, concrete filled, steel caissons, resting on 5&apos; deep rock sockets, at depths of 50&apos; to 150&apos; below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By Vhutali Carol Madanda, FHATUWANI SENGANI, François Mulenga

The first introduction of fuzzy theory in the nineteenth century created room for continuous research and application in various fields. Fuzzy set theory has been globally applied in geotechnical engineering, and research in this field continues to date. The fuzzy inference system is considered to be one of the most popular techniques adopted to resolve some of the geomechanical challenges faced in both surface and underground excavations. This paper unpacks fuzzy theory-based approaches in mine geomechanics with the aim of expanding the innovative application of the same approach specifically in tunnel geomechanics. This aim was achieved by conducting a review of recent successful and unsuccessful applications of fuzzy inference systems in underground excavations/tunnelling geomechanics. Indeed, this review has outlined some cardinal points associated with the ability of the technique to solve complex geomechanics problems. However, the success of the technique was accompanied by a few limitations associated with the methodology. Finally, a future outlook associated with the technique has been established.

May 15, 2023

By Luis Martín Tejada

Para la evaluación de la estabilidad de taludes en minería superficial se utilizan diferentes métodos de modelamiento y planeamiento como el de simulación numérica. En ese sentido, el presente texto describe el método de tensión-deformación, cuyo base se encuentra en el método numérico de elementos finitos, y así localizar la probable superficie de ruptura. También se describe los mecanismos de ruptura en taludes altos, el cálculo del FS y algunas características del programa de elementos finitos PLAXIS.

Sep 9, 2007

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006

By Jason M. Ryan

"Along with recent advances in computer technology have come cost-effective systems desiiedto evaluate fragmentation distributions through digital images of particles. In mining operations andmineral processing plants, important data from these systems is obtained through monitoring sizedistributions at key stages of the comminution process. Blast engineers apply this technology as atool for the validation of empirical fragmentation models so that predicted results are more meaningful."

Jan 1, 1998

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou&apos;gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008