Search Documents

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928

By Alain Blanchier, Gilles Gomez

Neighborhood pressure on quarries has become urgent to deal with quarry managers and operators must apply the most recent technologies and communicate it for long shelf life time exploitation, the quarry in which the work is located in urban or suburban environments needs to take into account blasting rules as well as site environment. The main problems to be addressed are:

Jan 1, 2009

By Turgut Yalcin

"Recent years have seen a resurgence of interest in flotation cell design, and one of the areas where attention is being focused is flotation in centrifugal fields which aims at increasing the flotation rates by forced bubble-particle contact.A new cycloflotation device was developed at Laurentian University and tested on the nickel ore of Falconbridge Limited in Sudbury. In comparison with conventional flotation, cycloflotation yielded at least seven times faster flotation rates in terms of the mass of solids floated per unit time per unit flotation volume, while producing concentrate grades similar to those of conventional flotation. These results, which were obtained with a bench-scale ""cyclofloat cell,"" suggest that cycloflotation has the potential of setting a new direction in flotation technology.IntroductionFroth flotation is no doubt the dominant separation technique in the mineral processing industry. Since its inception early in this century, much research effort has been and is still being expended on this process. Until recent years, emphasis seems to have been placed on the chemical aspects of flotation, but there is now an increased awareness for the need to improve flotation machine performance and more and more attention is being directed towards this area. In a 1982 article on ""Flotation Machines"" (Young 1982) it is stated that "" ... by now the design of the machines used would have reached a high level of perfection, ... In fact, this is not the case ... "".The process of flotation in a flotation device may be considered to take place in several distinct stages as follows:"

Jan 1, 1994

By Bryn Harris, Liming Huang, Andre Laplante

"This paper reviews flowsheets generally used in gold rooms to upgrade primary gravity concentrates particularly those of Knelsons. It is concluded that even for small operations, which treat between 250 and lo00 kg of concentrates per day, there is a strong economic incentive to include in the flowsheet magnetic removal of tramp iron, at least two shaking tables, screening of either table feed or table tails at 150-212 um, and scavenging of table tails with a small centrifuge. Headroom, rather than floor space, is often inadequate in most gold room designs, and limits gravity flow and flowsheet flexibility. Experimental data are presented to demonstrate the effectiveness of a small Knelson Concentrator to scavenge significant amounts of gold (up to 91 %) from fine table tails.RésuméCet article examine les schémas d’évolution généralement utilisés pour traiter les concentres gravimétriques d‘or, en particulier ceux produits par concentrateur Knelson. Nous en venons à la conclusion que même pour un petit circuit d’une capacité de 250 A 1000 kg/jour pourrait bénéficier des opérations unitaires suivantes : concentrateur magnétique pour extraire la feraille, au moins deux tables A secousses, criblage de l’alimentation ou du rejet d’une ou des tables i une maille de 150-212 um, et épuisages des rejets fins de table avec un centrifuge de petite capacité. C’est l’espace vertical du lieu où se fait cette concentration qui représente la contrainte la plus importante, plutôt que sa surface, puisqu’il faut maximiser l’écoulement par gravite des pulpes et s’offrir une certaine flexibilité quant à l’agencement final des opérations unitaires. Nous présentons également des données expérimentales pour démontrer l’efficacit6 d‘un Knelson de laboratoire pour récupérer jusqu’ à 91 % de l’or contenu dans les rejets fins de table."

Jan 1, 1999

By Thoedtida Thipparat

The diaphragm walls and barrettes are very important to the constructions of multi-storeyed buildings, elevated expressways, subway railway stations, etc. Uncertainties particularly increase in accordance with the construction progress. Overcoming uncertainties influences the construction goals including achievement of time. This paper is aimed at proposing an uncertainty assessment and delay evaluation model to assess uncertainties and evaluate delay resulting from those uncertainties. Neurofuzzy systems (NFSs) for assessing uncertainties and evaluating delays are developed. Artificial neural networks (ANNs) have ability for learning from the past data and generalizing outputs for the next applications which are provided for fuzzy logic systems (FLSs). FLSs have ability for exploiting the tolerance of imprecision and uncertainty. FLSs provide the reasoning to the ANNs. Uncertainties affecting each operation were assessed and delays were evaluated by following steps of the proposed model. The uncertainty assessment and delay evaluation approach was applied to a diaphragm wall and barrette construction to demonstrate how to implement the proposed model. The results of the test case application were used for handling delay at all operations regarding the corresponding uncertainties.

Jan 1, 2006

The production of metallic titanium and titanium-rich alloys in forms useful to the engineer involves the use of certain techniques not usually necessary in fabricating the commoner metals and alloys. However, not all stages in the handling and shaping of titanium-base materials require the application of unfamiliar methods. It is the purpose of this paper to indicate where the well-known techniques are applicable as well as to outline the unusual operations which are necessitated by certain chemical characteristics of titanium.In brief, the characteristics just mentioned are manifestations of the very great reactivity of titanium, especially at elevated temperatures. Liquid titanium burns vigorously when brought into contact with air. It also reacts with practically all refractories, causing damage to the latter as well as undesirable contamination of the metal. Even solid titanium undergoes serious superficial contamination when heated above 800°C. in air for more than a few minutes. In addition to an oxide skin being formed, oxygen enters into solid solution in the surface of the metal causing the latter to become hardened and eventually embrittled.Up to date, titanium has been made only on a pilot plant scale by methods which produce a spongy or powdered product. Refractory problems have prevented the development of chemical reduction methods for making titanium in the form of a liquid pool from which ingots of useful size could be cast. Therefore the first part of this paper will cover the consolidation of powdered or spongy titanium. The latter portion will provide a brief description of...

Jan 1, 1950

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Edmonds W, Jeffcoat R

The completion of the first two open hearth furnaces in the new No. 2 open hearth plant at Port Kembla will increase Australian production of steel by 350,000 tons of ingots per annum.The paper gives an outline of the essential features of open hearth design and auxiliary equipment required to operate the two modern open hearth furnaces at present being installed.INTRODUCTIONThe increasing demand for steel required by Australian secondary industries led to the decision to construct and operate No. 2 open hearth plant at Port Kembla. Two basic open hearth furnaces of the most modern design are under construction and it is anticipated that these units will be commissi.oned in September 1956. Australian steel capacity will thereby be increased by approximately 350,000 tons of ingots per annum.PLANT LAY-OUT AND CONSTRUCTIONIn the design and lay-out of this plant the emphasis has been on efficient material handling with simplicity of design and operation. Overseas methods were studied and these studies, together with experience gained at Newcastle and Port Kembla open hearth shops, enabled this plant to be built to a standard which compares favourably with any other in the industry.Initially two furnaces, each of 2,75 tons capacity, have been built, but provision has been made in. the design and lay-out to enable expansion to six furnaces.The location of the new plant in relation to the existing units will be noted in Fig. 5. It is one of the first units to be built in an area which will dovetail into a pattern for...

Jan 1, 1957

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Koch D. F A

An electrochemical study of the dissolution of gold in aerated cyanide solution shows that the dissolution rate is determined by the nature of the surface. A passive film (probably a basic cyanide) formed at -0·6 V vs a saturated calomel electrode inhibits both the anodic dissolution of gold and the cathodic reduction of oxygen. Thallium has an "activating" effect on these reaction mechanisms.INTRODUCTIONIn general the dissolution rate of a solid in a liquid is studied by weight loss measurements or analysis of the solution at known time intervals. However, if the solid is a metallic conductor, on which a redox reaction can occur at the metal-solution interface, it can be studied by electrochemical techniques. Electrochemical measurements have the advantage that the overall reaction can be separated into its components, in some cases by electrical measurements alone, and in others by a combination of these with analytical determinations.The overall equation for the dissolution of gold in aerated cyanide solution may be written4Au + 02+ 8CN- + 2H20 = 4Au (CN)2- + 40H- ..... (1)which can be separated into the two electrochemical componentsrepresenting the oxidation of gold and the reductionof ogygen respectively.4Au + 8CN-,= 4Au(CN)2- + 4eand O2+ 2H20 + 4e = 40H- These two reactions occur at the gold-electrolyte interface and it is the purpose of this paper to discuss the mechanism...

Jan 1, 1964

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By Mitchell L. Fong

The Bay Area Rapid Transit (BART) District will be extending BART service south along an 8.7-km (5.4-mile) -long corridor in the city of Fremont, California as part of the Warm Springs Extension (WSX). The WSX project will link the existing BART system to the future BART to San Jose extension. A segment of WSX is located in Fremont Central Park (referred to as the Fremont Central Park Subway Project). The Fremont Central Park Subway is considered the most complicated and geotechnically challenging portion of the project with an underground subway box being constructed near the active Hayward Fault which is capable of ground motions up to 0.75 g and is located in an aquifer which is used for water storage and supply. Soil-structure interaction analysis was used in the design of the subway box to resist deformations due to earthquake ground motions. A water-tight excavation support system has been designed to allow subway box construction while minimizing impacts to the aquifer.

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By H. R. Butler, J. F. Church, A. T. MacGibbon

Introduction Inco is the major North American nickel producer. Initially based in Sudbury, Ontario, its past exploration activity was directed toward finding new nickel deposits. New nickel sulfide discoveries outside Sudbury have included Thompson, Manitoba; Shebandowan, Ontario; and Widgiemooltha in Western Australia as well as a host of nickel laterite deposits. The company is currently diversifying into other commodities, including gold. Inco's exploration department participated in uranium discoveries in Saskatchewan and chromite discoveries at Tiebaghi in New Caledonia. In addition, it found new gold deposits at Lupin, Northwest Territories; Crixas, Brazil; Hoyle Township, Ontario; and Casa Berardi in Quebec. Crixas and Casa Berardi are currently being evaluated by underground exploration. Figure 1 shows some Canadian Shield gold locations where Inco is or was an active participant. Base metal developments Base metal exploration in shield areas has been greatly eased by applying scientific studies. Archean nickel sulfide deposits have been found using komatiitic-flow models (Fardon, 1971). Volcanogenic massive sulfide model has been applied to copper-zinc deposits (Sangster and Scott, 1976). Such deposits were subsequently seen developing on the sea floor through black smokers (Spiess, MacDonald, and Atwater, 1980). Sedimentary processes were recognized early as important in ore formation, particularly in the southern hemisphere (King, 1976). And many ore deposits are now regarded as a simple part of the geological column (Stanton, 1960 and 1972). Petrographic work on alteration patterns in and around ore bodies was used to develop standard porphyry copper models (Lowell and Guilbert, 1970). Epithermal models for precious metals followed. Stratigraphic zonation patterns have been formulated for base metal deposits, including keel facies, ore facies, and cap or distal facies. Gold developments The work on base metal deposits naturally spilled over into precious metal exploration when the gold price was allowed to float on world money markets. Early work on elements associated with gold deposits, especially arsenic, tellurium, selenium, and mercury, pioneered more detailed geochemical work (Bagby and Berger, 1985; and Groves, Ho, and Houstoun, 1984). Geochemical patterns have been recognized around microfine gold deposits. And the study of gold precipitation patterns in modern geothermal systems has helped understand gold deposition. In the late 1960s and early 1970s, it was noticed that numerous Archean banded iron formations contained anomalous gold values. From this and other observations, the syngenetic exhalite gold model has developed. Gold deposits also occur along shears in some plutons such as the Belmoral mine in Quebec. This indicates the importance of epigenetic processes in ore formation. Shield ore settings Initial studies recognized that the major gold camps in the Canadian Shield were mostly in greenstone belts and found along "breaks," especially zones of faulting and sedimentation. Gill (1948) wrote, "Only recently, as a result of detailed mapping, has the importance of major schist zones such as the Larder Lake, Cadillac, Porcupine Creek, and Destor Breaks been recognized. These zones of persistent adjustment mark broad belts favorable for ore occurrence." The importance of shearing in ore location and regional greenstone stratigraphic position close to late sedimentary packages was clearly understood. And structural models have been further developed for some Canadian ore deposits (Hubert, Trudel, and Gelinas, 1984). In the Beardmore-Geraldton camp of northwest Ontario, the importance was soon recognized of fold noses in banded iron formation, as localizers for gold ore. This importance had also been recognized in Western Australia,

Jan 2, 1987

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975