Search Documents

By David Kress

Mill crushing drive systems are essential to cement producers. With the increased emphasis on operating efficiency, it is vital that these systems be dependable and reliable. No one needs the costs or headaches associated with unscheduled downtime or inefficient machinery operation. A reliable drive system starts with the proper selection of the ring, or girth, gear and continues through proper maintenance. Ideally, selecting the right girth gear brings together the gear manufacturer, the system designer and the end user. The gear manufacturer must know the details of the application, the demands that will be placed on the gear and the nature of the equipment to be driven. Similarly, the user and the system designer must be familiar with the variables that affect gear drive performance and service. For example, an application that places a torque load on the drive in excess of its rated capacity will result in gear tooth distress and, in severe cases, breakage.

Jan 1, 2000

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By Valentín Pamo Caytano

La electrorefinación en un electrolito de CuSO4 - H2SO4 es usado universalmente para producir cobre de alta pureza a partir de los ánodos impuros. Aunque una parte de las impurezas se disuelve durante la electrorrefinación y se concentra en el electrolito, otros elementos son insolubles y se acumulan como lodos anódicos en las celdas de refinación. Las impurezas deben ser removidas del cobre para cumplir las especificaciones del mercado sobre la ductibilidad y conductividad y para recuperar los sub-productos valiosos como el oro y la plata. En ese sentido, el presente trabajo describe los equipos y procesos que permiten la recuperación del oro refinado en la planta de metales preciosos de la Refinaría de cobre de Ilo.

Sep 12, 2011

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By I. Demers

Doyon mine, Quebec, Canada evaluates the possibility of desulphurizing their tailings to produce material to be used in as cover over the acid generating tailings disposal site. Laboratory tests were conducted and showed that a single-layer cover made of desulphurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modelling with the software Vadose/W was undertaken to optimize the design parameters, namely cover thickness, water table position, and residual sulphide content of desulphurized tailings following laboratory work. It was found that the optimal configuration includes a 1 m desulphurized tailings cover containing 0.8%S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux towards acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective chosen for Doyon mine (10 mol/m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2008

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By C. Bazin

Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action to correct the problem. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality leading to a less efficient grinding operation. A dynamic simulator is used to assess rules for the diagnosis of hydrocyclone faults from the trends produced by sensors.

Jan 1, 2009

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By B Lumsden, B Lacouture

"Red Dog is one of the largest zinc mines in the world both in terms of reserves and annual production. In 2013, Red Dog produced 551,300 mt of contained zinc and 96,700 mt of contained lead. The mine, which is located in Northwest Alaska, is a partnership between Teck Alaska Incorporated, the operator of the mine and NANA Regional Corporation Inc, the local land owner. The Aqqaluk deposit, which is the current source of ore, has an average grade of 15.8% Zn, 4.1% Pb and 73 g/t Ag with the main minerals being sphalerite, galena, pyrite, barite and quartz. Surveys of the zinc flotation circuit at Red Dog identified that a substantial amount of fully liberated, sub 20 micron sphalerite particles were being lost to final tailings. As a means of improving fine sphalerite recovery, a four month plant trial of magnetic conditioning was conducted in the zinc retreat circuit. Magnetic conditioning technology has already been commissioned in several concentrators around the world to agglomerate fine paramagnetic minerals, increasing their probability of bubble collision and recovery in a flotation cell. The results of the four month plant trial at Red Dog showed that at a high level of confidence, a 1% increase in zinc recovery or zinc recovery and zinc concentrate grade combined was achieved with magnetic conditioning. The resulting economic benefit, which is also at a high level of confidence, is significant to Red Dog and therefore, magnetic conditioning has been permanently incorporated into the Red Dog zinc flotation circuit.IntroductionRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine."

Jan 1, 2016

By O. Güven

In recent years, there is an increasing demand on manganese consumption which stems from the important role of manganese in carbon steel production. And the growing need for manganese ores makes the beneficiation of low-grade manganese ores more economical. In this study, the characterization and beneficiation studies were carried out to propose a flow sheet for typical low-grade Turkish manganese ores. For this aim, different gravity separation methods were applied. According to the mineralogical analysis, the major mineral phases are pyrolusite (MnO2) and psilomelane (MnO2) while the major gangue mineral is radiolarite. Gravity separation tests were accomplished by using jigs, shaking table, MGS (Multi Gravity Separator) and in order to obtain products with high Mn ratio, high intensity magnetic separation was also performed. As a result, different combinations of flow sheets were utilized and a concentrate assaying 56.5% Mn with 85 % recovery was obtained.

Sep 1, 2012

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006

By Gualberto Salas

Dado que la voladura es una de las operaciones unitarias de mayor extracción del mineral -en tanto logra una adecuada fragmentación de la roca con un costo reducido, es necesario lograr una interrelación entre los resultados de la voladura y el de las operaciones unitarias como herramientas que evalúan y optimizan los diseños de los disparos. En ese sentido, el presente trabajo describe las técnicas para el diseño de las mallas de perforación, los programas para la simulación de la voladura y también para medir los resultados, que permitirán realizar los ajustes necesarios para mejorar los resultados de fragmentación y reducir el costo de operación de minado.

Sep 13, 2001

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007