Search Documents

By Jacques Nantel

Mechanization has been at the core of productivity improvements since the industrial revolution. During the past 20 years, mining has derived spectacular progress from mechanization. In the future, however, mechanization alone will not be enough. In the next few decades, automation will bring about new generations of highly productive and safe machines, with low operating costs. Increased use of new and better technology is generally accepted as the prime factor capable of closing the productivity gap. The productivity gap is the difference between inflation and metal prices. The three S-curves in Fig. I represent the evolution of technology in general, and mining in particular. TI represents incremental changes. the dominant sort of technology changes in the mining industry: - Better drills, electric hydraulic drills vs. pneumatic drills, the drilling rate is twice as fast. - Better steel and bits, to accommodate the higher performance drills. - Improved chemical explosives. - Bigger trucks in open pits.

Jan 1, 1993

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By Lee T. J

The area, A, under a gamma-ray log that passes through a horizontal bed given by: A = gl/k. Here is the equivalent concentration of U3O8 in the body, l the thickness of the body, and k the calibration factor or sensitivityof the logger. The area is independent of the logging speed or logger time constant.This relationship, together with the first moment about the maximum of the log and its value there suflicient to determine the thickness, position of the centre of the bed from the log maximum and the concentration of U3O8.Numerical results obtained from artificial and field data show that the computed results arc as good as those obtained by methods such as the inverse filter technique and the iterative method. The present method yields results that arc easier to feed into an ore reserve data base.

Jan 1, 1981

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By R. Cotton

"1. INTRODUCTIONTo say that the environment will be a dominant issue in the 1990' s is an understatement. A world-wide ""green revolution"" is taking place not only with the general public and politicians, but in the boardrooms and plant facilities of corporations around the world. There is probably not a plant manager who has not been requested by his corporation to assist in some way on environmental issues by providing advice and strategy, by dealing with customer or community concerns, by considering environmental matters in transactions, by developing new environmental compliance policies and requirements, and so on.There are, in the author's view, three main challenges for the mining industry in the environmental area in the 1990's. This paper will discuss each in turn. The first challenge is the concept of ""sustainable development"". Whatever the meaning of this much-debated phrase, we are rapidly moving beyond the buzzword, and into the specifics. It will clearly impact on the way we manage our companies, our communities and our personal lives.The second is the challenge of personal liability; particularly for officers, directors, supervisors and managers of the corporation. For example, in Ontario today, a good percentage of prosecutions for pollution offences are against individuals, usually managers and supervisors, in addition to the prosecutions against the corporation itself for the same offence. In all likelihood, prosecutions will increase in number and will increasingly be directed at individuals. A corporate president has already served a jail term for contempt of court related to his corporation's breach of a court order related to sewer by-law offences. Although the case is on appeal, another president has become the first officer in Canada to be sentenced to jail for violation of an environmental protection statute. Other corporate officers and directors have recently been charged with breach of their duty under Ontario's Environmental Protection Act."

Jan 1, 1991

By Wingham D. W

Based upon the previous work of Norman & Loeb, a method was used to assess the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa, The materials to be tested were obtained in the form of large diameter balls, and were run, along with the regular ball charge, in a large ball mill operating under normal grinding conditions. At selected intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.INTRODUCTIONInformation in metallurgical journals, from local iron and steel foundries, and from various metal promotional organizations has suggested that the various alloy compositions available should be examined and assessed for possible use as milllfners and grinding media.Previous attempts at evaluation of recommended materials for these applications elsewhere, have usually involved the purchase of large quantities of grinding balls or complete mill liner sets, requiring running periods of up to two years or more. As well as being both a costly and lengthy procedure, the information obtained may be of little significance, due to changes in milling practice, and ore characteristics during the period of operation.To overcome these difficuities, a method was adopted based on the short time wear rate test recommended by Norman & Loeb (1949) and Norman (1957) in which all the materialsunder consideration are ·subjected·concurrently to the conditions of service.Previous calculations of wear rates have been dependent1. Senior Metallurgist (Materials), Mount Isa Mines Limited.2. Metallographer, Mount Isa Mines Limited.Manuscript received at The Institute, 22nd April, 1963, and presented to the1963 Annual Conference.

Jan 1, 1963

By W. I. Watson

The study considered all the institutional, resource reserve, technological, and economic factors relevant to the industry's present and future status, such as markets and marketing techniques, competition from other producers both domestic and foreign, federal and state regulations affecting the industry, quarrying and processing technologies, slate reserves and resources, and industry structure and economics. Constraints to the growth of the industry were assessed and scenarios proposed to solve some of the problems.

Jan 1, 1980

By Michael Kukay, Paul Conrad, Cosmas Opoku-Ware

This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 ft below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana.

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

By Peter Campi, Harry R. Asche, Ian P. Callow, Edmund G. Taylor, P. Scott Smith

The US$1,850 million EastLink project is a 39km tollway and includes twin 3-lane,1.5km long, undrained driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and so to help preserve the unique flora and fauna in the area. This paper describes several of the key issues in the tunnel design and construction, including: the integration of the temporary support design with the Contractor’s tunnel excavation and support procedures, including sharing of responsibility between the Designer and Contractor for support type selection and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. detailed hydrogeological assessments during the design and construction phases to allow confirmation of design loads for the tunnel lining design and the various suite of waterproofing tools in order to meet the project inflow requirements. development of a pre-cast invert solution to the main tunnel secondary lining to enable faster lining construction and to minimize risks to the tunnel membrane associated with fixing reinforcement and construction traffic.

Jan 1, 2007

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By William H. Highlands

Lightning is a natural phenomenon which poses a potential hazard to people, structures, and equipment unless adequate protection is provided. The type of protection required is related to the nature and of the facility. The decision making process involves a number of interrelated factors which should be considered when determining the need for protection.

Jan 1, 1989

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By Carlos Soria

El presente texto describe los Sistemas de Gerencia de la Información y su aplicación en la industria minera con el objetivo de optimizar la gestión total de la empresa. Dichos sistemas manejan información del proceso y sus valores de producción, cálculos, consumos de energia, emisiones de plantas, tiempos de funcionamiento de equipos, eventos, alarmas, mediciones de laboratorio y control estadístico, etc. De forma que dicha información pueda ser reunida y consolidada, convirtiéndose en materia de significado y relevancia disponible en base a análisis, reportes, listas, tendencias y gráficos para que el usuario final de una planta o en sus oficina pueda tomar mejores decisiones.

Jul 17, 2000

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By P Williams, S Flynn, R Birchfield, R Simcock, R Toft, P Comeskey

Direct transfer, or community translocation, comprises salvage and replacement of intact æsodsÆ of vegetation together with underlying soil. It has been applied to New Zealand mine sites restoration of native grasslands, wetlands, scrub lands, and forest. It is an equivalent technique to æinstant lawn or tree gardenÆ, commonly used in urban landscaping. Two to six m2 scoops of vegetation, with up to 0.7 m of soil attached, and including root plates of trees and shrubs, are relocated from stripped areas ahead of mining to sites prepared for restoration. Direct transfer uses hydraulic excavators or face shovels and dump trucks, possibly with the aid of bulldozers and other earthmoving machinery. The main advantages of direct transfer, compared with sowing or planting systems for mine site restoration, are the recycling of plant and soil materials which were often wasted by burying under overburden materials, a significantly faster revegetation process, and restoration of the whole ecosystem (plants, animals, birds, invertebrates, and microbes). The main disadvantages are higher costs of stripping and dumping, a greater degree of machine operator skill required, and scheduling becomes critically important. To illustrate the key principles, this paper gives examples of successes and failures of the technique for a variety of New Zealand mining situations. Direct transfer has been successful for a range of communities, from fern wetland and sub-alpine tussock grasslands to 5 m-tall beech forest under storey and seral shrub land, and from temperate to sub-alpine climates. Successful examples show both rapid recovery of indigenous vegetative cover and conservation of habitat for birds and invertebrates. Failures have resulted from excessive death of plants because of inadequate soil salvage depths, acidic leachates, inappropriate handling of stripped sods by inexperienced machinery operators, or prolonged drought conditions immediately following relocation. Change in plant species composition has occurred where clumps of vegetation are too far apart, or shifted plants were too small - in both cases invasive weeds have smothered the original vegetation. Changes in hydrology can also have significant impacts. Our experience indicates that the advantages of direct transfer far outweigh the disadvantages and is now used as the preferred restoration method, where practicable, at mines where it has been trialled.

Jan 1, 2000

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954