Search Documents

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By Peter White

The Hemlo Gold District, located on the north shore of Lake Superior, was discovered in 1981 and will become one of the largest gold mining camps in Canada. Three major Canadian mining companies are presently developing large orebodies and are scheduled to commence production at various times through 1985 and 1986. This paper describes the types of shaft sinking equipment and technology being used by contractors in constructing the required shafts to depths below 1000 metres. The principal shaft design criteria, types of shaft sinking machinery and relevant manpower allocations are discussed.

Jan 1, 1985

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By M. Makarchian

Existing buildings sometimes experience excessive settlement under their design loads, or due to increased foundation loading, if a change of building use is required. One of the oldest and widely numerical study has been carried out of a simple idealised problem of an underpinned rigid circular foundation to better understand the behaviour of pile used for underpinning and load transfer mechanism from an existing foundation to the underpinning piles. The finite element method has been used for this analysis, with the soil treated as a two-phase elasto-plastic material. It is found that the effect of the length of the pile becomes more significant as pile length increases. As would be expected, the earlier the pile is installed, the less is the final settlement.

Jan 1, 1996

By Robert Martin, Brian W. Stump, David P. Anderson

2We use field measurements to quantify physical processes that accompany different types of mining explosions. The data sets collected include three-component ground motion, acoustic, video and high speed film, three dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions include simple single-fired contained explosions, ones designed to bulk and fracture material and those that cast material. Our goal is a physical understanding of these sources for the purposes of optimizing blasting practices.

Jan 1, 1998

By NA UMC

Abstract Booklet

Dec 2, 2023

By R. F. Kehrman

Voice Frequency (VF) electromagnetic trapped miner location devices were tested for reliability and effectiveness in 93 coal mines. Tests included uplink pulsed CW, downlink pulsed OW and downlink voice evaluations. Frequencies were 630, 1050, 1950 and 3030 Hertz. Overburden depths varied from 70 feet to 1550 feet. Successful communications were established at 91 of the 93 mines. Data indicate the transmitters and receivers will operate in practically all coal mine environments. Reliability and accuracy as location devices appear to depend on noise, depth and presence of metallic objects which distort the magnetic field. In addition, theoretical models appear to define best case situations in terms of noise and conductivity. Minor hardware problems were encountered, mostly involving battery contacts, switches and antenna cables on the receivers. No hardware problems occurred with the transmitters.

Jan 1, 1978

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

Samples of a refractory copper ore were examined to test their response to segregation roasting, flotation, and acetonitrile leaching. Recoveries in the segregation roasting stage were between 60 and 100 per cent, while flotation recoveries varied between 60 and 85 per cent in cleaner concentrates assaying 25-40 per cent copper.The fraction of the copper which could be leached from the concentrate by an acetonitrile/sulphuric acid/cupric ion leach solution varied from 16 to 97 per cent, the lower recoveries being correlated with the presence of sulphide in the concentrate.

Jan 1, 1973

By Yoshihiro Kawarabata

INTRODUCTION With only about 30% of Japan's entire population served by sewer systems at the end of 1980, extensive sewerage construction programs have been implemented. As major sewer networks in large cities are near completion, construction of smaller sewer networks in less populated areas and branch sewers in urban areas is on the rise, where a demand for sewer tunnels of 600mm to 1500mm diameter is very heavy. The pipe jacking technique, usually employed to excavate such small diameter tunnels, therefore has become the subject of further technological development and sophistication to cope with the increasing volume of construction. At the 1979 RETC, the state of the art on the slurry shield tunneling method at that time was reported. This paper is a follow up to the last paper and discusses a newly developed boulder crushing equipment and automatic pipe jacking system for the slurry shield method and their application. Such technological advancement as high-degree mechanization and automation will significantly improve tunneling operations in response to the aging society to come. Through application of the technique on so called factory automation, this is a step towards field automation for the construction industry.

Jan 1, 1983

By Mohab Sabry

Pile foundations are used extensively around the world to support both inland and offshore structures, including important structures such as nuclear plants and oil drilling platforms. The limit of the pile depth is currently predicted during the pile deriving process, given no chance for the designer to predict accurately the capacity of these piles prior installation. Furthermore, after pile installation, designer may not be able to modify the pile group design by increasing the number of piles and or changing the geometry of the pile group. This paper presents a numerical model for the case of single piles driven in homogenous sand using finite element technique and the theory of cavity expansion. The model is capable of simulating all the construction stages of concrete piles up to the maximum depth, which can be driven in sand and accordingly the capacity, which can be attained by these piles. The program "PLAXIS" is used to perform the proposed analysis. This model simulates the process of pile driving in terms of the changes in the earth pressure and the overconsolidation ratio acting along the pile's shaft. Based on the results of the present investigation, these depths can be predicted based on the pile geometry and the sand properties. Charts are given to provide these depths for given pile/soil conditions.

Jan 1, 2006

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

At Great Boulder Gold Mines Ltd. a number of attempts were made to remove water soluble copper and iron salts from calcined pyritic concentrates but variou~ problems arose and the methods were abandoned.A method of rapid washing has been developed and although some problems still exist a workable process was established which resulted in substantial savings of reagents used for the cyanidation of calcine.INTRODUCTIONIn the Great Boulder flowsheet crude ore is ground in cyanide solution, then thickened, agitated and subjected to two stage filtering. Secondary filter discharge is pulped with flotation circuit water, gassed with sulphur dioxide to precipitate soluble gold and activate pyrite, and after the addition of copper sulphate and xanthate, the pyrite and tellurides are recovered by flotation. Flotation tailings are thickened and pumped to the disposal area and concentrates are calcined in Edwards roasters. Calcine is washed to remove water soluble copper and iron salts and the washings pumped to the flotation section where the copper is used as an activator. The washed calcine is cyanided and returned to the crude ore circuit via the thickeners. Solution for precipitation in the Merrill Crowe is drawn from the crude ore thickeners.Prior to the introduction of calcine washing the calcine contained 7 lb/ton copper of which approximately 60 per cent was water soluble. It also contained approximately 90 lb/tol'l of water soluble iron salts. Both the copper and...

Jan 1, 1964

The presence of gold or tin in a particular place in payable quantities may be suspected from geological and prospE;cting reports. It behoves the engineer by judiciously spaced boreholes or pits to establish whether the place is exploitable with profit, and it is the purpose of this paper to set out the ways in which this is done. The various types of deposit to be considered occur in Malaya, Thafland and Borneo, in which countries the writer spent four years in estimating alluvials.The methods described were used in actual practice both by the writer and previous engineers for the same company. The subsequent exploitation of the alluvials evaluated by the methods given below shows that the recovery was as good as, and sometimes higher than, expected. No claims are made to the originality of the methods, but it is 'felt that they may be new to some engineers and< interesting to others contemplating alluvial testing.

Jan 1, 1942