Search Documents

By David G. Winter

The first test pile for the carrier pier and south wharf at NAVSTA Puget Sound was driven on December 27, 1989, and the final pile was tested on February 26, 1990. Implementation and modification of the test pile program were done by the owners (WESTDIV and ROICC-Everett), the engineers (ABAM and Hart Crowser), and the contractor and his subcontractor (General Manson Joint Venture and GRL). The site is located as shown on Figure 1. SUMMARY OF THE SOIL CONDITIONS A soil profile along the pier is shown as Figure 2. The soil units can be generalized as follows: ? Upper Silts - Fill, sandy silt, and clayey silt extending from the mudline to an elevation of about -80 feet; ? Intermediate Sand - A medium dense to very dense silty sand unit which is about 30 feet thick near the shore, but thins and disappears offshore; ? Lower Silts - Sandy silts and clayey silts in a medium stiff to stiff condition; ? Deep Sand - A very dense overconsolidated sandy soil encountered at an elevation of about -145 feet.

Jan 1, 1990

By Allan Sylvester

This paper will discuss the design, construction, and performance of the support of excavation on the San Diego State University LRT Station. The vertical elements of the system include drilled secant piles and drilled soldier piles. We will discuss the geo-technical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the pile and support of excavation systems. In consideration of the conference theme, there will be a discussion of the successful accomplishment of meeting the interim milestone dates of the Contract. The project team cooperatively worked to design and install approximately 1,100 drilled secant and soldier piles as well as excavate and install the balance of the support of excavation elements in such a manner as to minimize the disruption to campus students and operations.

Jan 1, 2002

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

By Lance A. Roberts

Micropiles are commonly utilized for applications other than foundation retrofit. In bridges, for example, micropiles can serve as the permanent foundation elements or can be used in temporary support applications. In this paper, a case study on the use of micropiles for the 18th Street Expressway Bridge rehabilitation/repair project in Kansas City, Kansas is presented. In the project, micropiles were utilized for support of six temporary jacking structures, which allowed the bridge to be lifted while repairs were completed. A group of six micropiles was required to support each jacking structure. The required compressive service load per micropile was approximately 300 kips (1300 kN) and the settlement of the micropiles under the service load was to be limited to 0.5 in. (12.7 mm). Two field compression tests were conducted as part of the project. The field load test data was integrated within a soil-structure interaction capacity approach in order to analyze and permit the shortening of the design bond length for the production micropiles.

Jan 1, 2009

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in1994 initiated a dynamic shift in the ownership, management and development of the country?s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress?s Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since then there have been important changes affecting the rules of mineral development. These are: ?A drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully ?The globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists and ?The introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its regulations, the much publicised Broad-Based Socio-Economic Empowerment Charter, its associated Scorecard, and the Draft Royalty Bill.

Jan 1, 2004

By Paul R. Smith

The Colorado School of Mines Research Institute (CSMRI) was founded in 1949 to fill mining industry and government needs for minerals research and development. The operations of scores of mines, mills, and plants around the world are based on the results of work done by the Research Institute. Among other things, the Research Institute conducts studies in geology, mine planning, mineralogy, size reduction, minerals processing, and hydrometallurgical techniques in extractive metallurgy. Many CSMRI projects also involve energy and environmental considerations. What follows is a summary of some of the studies in which the Research Institute has been and is currently involved, as well as some comments on trends and developments in the industry.

Jan 2, 1982

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

By X. Zhou

In this study, the cyclonic static microbubble flotation column (FCSMC) was investigated for fluorite beneficiation. The structure and principle of the specially designed column are described. Fluorite samples from the tungsten separation tailings of the Shizhuyuan Mine, Chenzhou, Hunan Province, P.R. China, were tested using a small-scale continuous flotation test unit, and concentrates with a fluorite grade higher than 98% were obtained. One rougher and three cleaner stages in the FCSMC achieved the same separation performance as one rougher and eight cleaners in conventional flotation cells. This greatly simplified the flotation circuit and reduced operating costs.

Jan 1, 2007

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003