Search Documents

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By D. Limpitlaw

The origins of mine closure practice have influenced the way in which it is implemented by companies and regulators. Mine closure practices essentially started developing in the 1970s in countries with advanced economies and mature mining industries. In these settings, the emphasis was justifiably placed on restoration of the landscape and an attempt was made to return to the ?natural? pre-mining land cover. These practices continued to evolve and incorporated socio-economic and cultural aspects, especially after the Brundtland Report in 1987 and the subsequent Earth Summit in 1992. Today mining is increasingly occurring in remote parts of developing countries where there may be significant need for infrastructure such as roads, clinics, and schools. The costs of returning land to low (economic) value pre-mining use may be far greater than establishing a viable postmining land use that could potentially add value to the community and take pressure off sites for greenfield development elsewhere. Furthermore, natural resource limitations (such as topsoil availability) may limit the degree to which the historical land cover can be re-established. Establishing post-mining land uses may aid in mitigating the loss of employment that is inevitable when mines close. Stakeholder participation in establishing post-mining land cover and land use options is critical for long-term success. Similarly, third parties must be identified to support the development of the post-mining land use This paper draws on the experience of the authors in several developing countries and presents a case for maximizing re-use of mining infrastructure. The paper does not advocate the adoption of poor rehabilitation standards, nor or the wholesale destruction of land capability, but rather leaving key infrastructure in place for post-mining use that may support sustainable development.

Jan 1, 2014

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

A description is given of the construction and operation of an automatic version of the coarse batch particle sizer which requires a minimum of operator supervision and which is capable of processing a sample every 4 min.

Jan 1, 1968

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

For many years the scrubbing of roaster gas carrying sulphur dioxide has been carried out at the plant of the Electrolytic Zinc Co. of Australasia Ltd. at Risdon, Tasmania, using long horizontal tubes. in which the gas stream crossed a shower of water. In order to provide for increased roaster capacity, it was evident that additional gas scrubbing capacity would be required to prevent pollution of the atmosphere.This provided an opportunity to review the whole operation of gas scrubbing and an investigation was initiated to determine the characteristics of a counter-current type of scrubber. It was hoped that a change to this type of scrubbing would also reduce the sulphur dioxide concentration of the gas delivered to the atmosphere to a negligible amount. This, paper outlines results obtained from an experimental tower which was operated under a wide range of conditions, the packing height, gas flow, water flow, water temperature, and concentration of S02 in inlet gas being varied independently. A description is given of the leading features and operating characteristics of the plant units, which are designed on the basis of the experimental results. Operation of the new scrubbing system commenced on October 5th, 1948.THE PROBLEMThe gas which is handled carries S02 which may vary in concentration from 2% to 5%, and reaches the scrubbing system at a temperature of approximately 180 deg. C. An appreciable amount of suspended material accompanies the gas which has passed the cyclone system.

Jan 1, 1949

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

By Jean-Marc Simard, Vincent Jourdain, Denis W. Roy

"Seven lithologic units, informally characterized, were recognized in the vicinity of the Montauban orebody. The first five lie in stratigraphic order. From structural bottom to structural top these are: (1) grey composite gneiss; (2) dark grey quartz-biotite gneiss; (3) quartz-biotite-garnet gneiss hosting several calcareous, aluminous and magnesian members and gold mineralization; (4) light grey quartz-muscovite-(sericite)-biotite gneiss; and (5) metabasafts. The last two intrude the sequence: (6) amphibolite dykes and (7) pegmatite veins. The orebody lies on the inverted limb of an overturned synform verging to the west with the metabasafts marking the core of the fold. As the foliation is folded, this fold is attributed to deformation ""D2""; deformation ""DI"" being responsible for the formation of the foliation. A late brittle deformation developed shear zones with probable strike-slip motions. The refined stratigraphy and the identification of the structural position of the orebody provide new tools for regional interpretation and prospecting.RESUMESept unités lithologiques ont été définies informeffement à proximité du gisement de Montauban. Les cinq premieres reposent en ordre stratigraphique; ce sont de la base au sommet structural: (1) le ""gneiss mixte gris""; (2) le gneiss gris forcé à quartz biotite; (3) le gneiss a quartz-biotite-grenat comprenant plusieurs membres calcareux, alumineux et magnésiens ainsi que la minéralisation aurifère; (4) le gneiss gris clair à quartz muscovite- Isericitel-biotite; et (5) les métabasaltes. Les deux autres unites sont intrusives dans la sequence: (6) les dykes d ‘amphibolite et (7) les veines de pegmatite. Le gisement se sitlie sur le flanc inverse d'un synforme déverse vers I' ouest dont les métabasaltes occuperaient le cœur. Comm e la foliation est plissée, ce pli est considère appartenir d la deformation ""D2""; la deformat ion ""DI"" etant responsable de la formation de lafoliation. Une deformation cassante tardive se traduit par des zones de cisaillement, d rejet apparemment directionnel. Cette stratigraphie plus précisé et l'indentification de la position structurale du gisement fournissent de nouveaux omits de prospection et d'interprétation regionalé."

Jan 1, 1987