Search Documents

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

By Gregory Yates

INTRODUCTION Project Description The Silver Line is a Bus Rapid Transit (BRT) Line and is Boston?s newest transit service. Silver Line Phase I extends along Washington Street entirely on the surface in priority bus lanes from Dudley Station in Roxbury through the South End and Chinatown neighborhoods to downtown Boston. The Phase I opened in July 2002. Silver Line Phase II consists of an underground transit tunnel from South Station to the South Boston Waterfront with underground stations at Courthouse and World Trade Center to Silver Line Way east of D Street. Phase II continues through the Ted Williams Tunnel to all the terminals at Logan Airport, and on the surface to the Boston Marine Industrial Park and City Point. Phase II opened in December 2004. Silver Line Phase III is a one mile tunnel connection to the existing Phase II tunnel in the vicinity of South Station and will eventually portal on Tremont Street just north of Marginal Road. After leaving the portal, the buses will use dedicated bus only lanes on the surface roadway network to connect to the Phase I service. Figure 1 shows the alignment of the Silver Line upon completion of the Phase III project.

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

By R. S. Warfield

Several reconnaissance-type surface and drill core samples of Arctic Northwestern Alaska coals were taken during the summer field seasons of 1964 and 1966 for coking studies. Surface samples were taken from the Kokolik River and the Cape Beaufort areas; core samples were obtained from the Kukpowruk River and the Cape Beaufort areas. Only one Kokolik River surface sample possessed coking properties. This sample, representing an 11.6-ft coal seam, made coke approaching metallurgical quality when a 30-pct portion of selected blending coals was added. Four Kukpowruk River core samples, each representing the same 19-to 20-ft coal seam, were all of about the same coking quality. No differences of coke quality attributable to depth of permanently frozen overburden were found, but the data confirm previously reported information that the 19- to 20-ft coal bed is a potentially satisfactory base coking coal. In the Cape Beaufort area, a core sample with appreciable coking properties was taken at depth from a coalbed determined noncoking in a surface sample.

Jan 1, 1969

By Silvano Morelli, Giovanna Cassani, Renzo Bindi, Antonio Nicola

More than 70 km of main line and service tunnels have been excavated to date for crossing the Apennines between Bologna and Florence. A new design and construction approach, known as Analysis of the Controlled Deformation in Rock and Soils, (ADECO-RS), was adopted to tackle the extreme heterogeneity of the ground and the particular stress-strain conditions. The goal of this system is to obtain constant and predictable full section advance rates, even in very poor geology, with the highest possible level of safety and reliability. The execution of this gigantic project required the mobilization of 21 job-sites, with the concurrent operation of 30 excavation headings. The global production rates confirm the high quality of the design and the high level of industrialization reached during the construction stage, levels not previously obtained in similar conditions, using other approaches such as NATM.

Jan 1, 2003

By D Chappell

Coromandel Peninsula gold mineralisation has an epithermal style which involves extensive alteration of host rocks and addition of pyrite over large volumes of rock. These altered rocks therefore have high potential for generating acid rock drainage. Natural acid groundwater discharges occur in altered rocks, but not in propylitically altered rock. There is little calcite available in mineralised rocks to neutralise this acid. In contrast, the mesothermal veins of the Otago Schist cause little alteration of the host rock, and that alteration has similar mineralogy to the host rock. Calcite is a common mineral in host and mineralised zones, and sulphides are generally subordinate. Hence acidification of Otago rocks is unlikely. This lack of acidification in Otago facilitates arsenic mobility in solution, up to hundreds of ppm. Arsenic is insoluble under acidic conditions in the Coromandel. Base metals are soluble under acidic conditions of the Coromandel, but they are immobilised by adsorption on to the widespread clay minerals where the solutions are neutralised. Base metals are generally immobile in Otago, but when they are mobilised, adsorption is less effectiveas an attenuation mechanism because clay minerals are rare.

Jan 1, 1998

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962

The Kalgoorlie Tailings Retreatment Project (or "Kaltails") involves the reclamation and retreatment of approximately 50 million tonnes of gold tailing situated on the Golden Mile at Kalgoorlie, Western Australia. Tailing is reclaimed and retreated at the rate of 42 million tonnes per annum. The project is a Joint Venture between Poseidon Limited and Gold Corporation, with Poseidon being the major participant (90%) and manager of the operation through its wholly owned subsidiary Kaltails Mining Services Pty Ltd. The marginal nature of the tailing retreatment project dictated that a detailed feasibility study be undertaken. Extensive sampling and metallurgical testing of the tailing permitted the development of an optimum economic processing route. A sensitivity analysis undertaken as part of the feasibility study indicated the project to be very sensitive to gold price and unit operating cost variations, and relatively insensitive to capital cost variations.

Jan 1, 1990

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By Stephen Iverson

The National Institute for Occupational Safety and Health (NIOSH) is currently performing research to help mine operators minimize the amount of loose or damaged rock surrounding a blasted opening. Improperly designed blast rounds can result in excessive wall rock damage that may reduce the rock mass competency and increase ground support requirements. Unnecessary blast damage can cause many safety and operational concerns including an increased potential for injury from rock falls and other hazards resulting from sub-optimal blast designs. This paper focuses on the ground control and safety implications of blast damage in underground mines. A reduction in rock quality due to blasting can increase the amount of ground support required. Case study data collected by NIOSH in underground metal mines during standard drill and blast production rounds included blast vibration monitoring, detailed three-dimensional laser scanning of the as-built excavation, and geotechnical mapping of development headings.

Jan 1, 2007

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901