Search Documents

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By Eric Dussell

Commercial or industrial explosives are mechanically-mixed, fuel-oxidizer composites which exhibit varying degrees of non-ideal behavior. Non-ideality results from a relatively slow and state-insensitive reaction rate (Lee, 1990) and is characterized by C-J pressures, velocities or expansion isentropes significantly lower than those expected from equilibrium, steady-state calculations such as Tiger or BKW (Mader, 1979). This departure results from significant amounts of explosive material which remain unreacted at the sonic point. Energy released by continued combustion within the emergent supersonic region downstream of the sonic point, constrained by local sound speed, cannot flow to the shock front and do work on it. The significant amount of this ‘late energy” and its slow time rate of release must be considered in any blast performance model.

Jan 1, 1997

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By F. Dai

Granitic rocks usually exhibit strongly anisotropy due to pre-existing microcracks induced by geologic loadings. The understanding of the rock anisotropy in mechanical properties such as tensile strength is critical to quarrying and stabilization of underground structures. In this paper, Brazilian tests are conducted in combination with MTS material testing machine and split Hopkinson pressure bar (SHPB) system to measure both static and dynamic tensile strength of anisotropic Barre granite. Samples are cored and labeled using the three principle anisotropic directions of Barre granite (BG). These directions are also chosen as the loading directions for the Brazilian discs. For dynamic tests, pulse shaping technique is used to achieve dynamic equilibrium in the samples during the test. Finite Element Method is implemented to formulate equations that relate the failure load to the material tensile strength employing a orthotropic model for Barre granite. For samples in the same orientation group, the tensile strength shows clear loading rate sensitivity. The tensile strengths exhibit clear anisotropy under static loading; while less anisotropy under dynamic loading. The tensile strength anisotropy of Barre granite is interpreted as interactions of the pre-existing microcracks.

May 1, 2009

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications. The coal program of the Bureau of Mines extends over the wide range of applied and theoretical studies indicated by the table of contents of this report. Applied studies are conducted in connection with the development and evaluation of new mining techniques, and the effective processing and utilization of coal and coal products. Analyses of coal, technical advice, and other assistance to Federal agencies in connection with fuel and boiler-water problems, and health and safety activities are among the practical services handled by the Bureau, Fundamental research such as that on coal structure and on the properties of coal is conducted because it will, over a period of the, furnish an increasing general knowledge about coal; scientists and engineers may use this knowledge in solving problems in mining and utilization of

Jan 1, 1963

By R. H. Hiltz

The Coal Mine Health and Safety Act of 1969 legislated maximum dust levels for the working place. As the law was implemented, extensive efforts were undertaken to provide the technology necessary to control dust generation. One approach to dust control was the use of high expansion foam in place of the usual water sprays on coal cutting equipment. At the time of the act, high expansion foam had already seen considerable testing for the suppression of dust in underground coal mines. Work by MSA, several coal companies and the Bureau of Mines itself had provided data which showed foam to have some merit as a dust control mechanism. It suffered in a few areas, however, which limited its practical application. Its principal difficulty was persistence which hampered operations due to foam buildup, but problems were also encountered due to equipment size and form.

Jan 1, 1975

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By L. F. Contreras

In open pit mine design, it is customary for geotechnical engineers to define the appropriate slope design angles within practical limits. The conventional approach to slope angle design is based on the comparison of calculated stability indicators, such as the factor of safety (FS) and the probability of failure (PF), with generic acceptability criteria not directly related to the impacts of failure. A major drawback of this type of approach is related to the difficulty of defining meaningful acceptability criteria. An alternative methodology of pit slope design is proposed, where the economic impacts of potential slope failures are calculated and used as the elements on which to apply the acceptability criteria for design. The methodology is based on the construction of a graph, referred to as a risk map, that relates the probability of exceeding the economic impact of slope failure to the magnitude of the impact measured in monetary terms. The process includes the analysis of a selected number of representative years of the mine plan and slope sections of the pit areas to define the required inputs for the construction of the risk map. The paper discusses the concepts used in interpreting the probability of slope failure, and describes the approach followed for the estimation of the economic impacts of slope failure and the construction of the risk map. Finally, the two main uses of the risk map are discussed, including the comparison with acceptability criteria for the evaluation of a specific open pit design and the comparative analysis of open pit design options in terms of value and risk to identify optimum pit layouts.

Jan 1, 2015

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

By G. Denton, P. den Hoed, A. Luckos

The potential application of fluidized beds in several sectors of the ferroalloy industry is promising. They can be used in the direct reduction of iron ores to produce a feed for steelmaking, in the reduction of manganese dioxide to produce a lesser oxide for feeding to smelters, in the preheating of chromite for the production of ferrochrome, and in the calcining and pre-reduction of nickel laterites for the production of ferronickel. This paper discusses the potential of fluidized beds in theses processes and highlights the advantages of the technology over other technologies, such as rotary kilns. Two primary advantages?(1) that fluidized beds can treat fine materials and (2) that fluidized beds can be integrated with smelters in a way that allows for more efficient use of energy?may well see the technology gain prominence as more deposits of lower grade are mined and industries strive to use their resources more efficiently. In discussing the potential of the technology in the ferroalloy industry, this paper focuses on the application of fluidized beds in the smelting of chromite, nickel laterites, and manganese ores. Central to the successful operation of this technology is a knowledge of how particle properties influence the behaviour and design of fluidized beds.

Jan 1, 2007

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By K. Lapakko

Several static tests estimate the capacity of mine waste to produce and neutralize acid and are used as tools for predicting metal-mine waste drainage quality. Various methods and their accuracies are addressed. More accurate quantification of these capacities, as well as their availability and reactivity, may be necessary to predict drainage quality from some mine wastes. Chemical analyses, x-ray diffraction, optical microscopy, scanning electron microscopy, and electron beam analyses are among the techniques commercially available to more accurately quantify these capacities and provide insight into their availability and reactivity.

Jan 1, 2003

By I. Mc Dougall

Finite element models were generated of two submerged arc furnaces of different geometries. A 48MW circular furnace and a 68MW 6-in-line rectangular furnace were studied. The electrodes, raw material, slag and molten metal were included in the model. ANSYS/Multiphysics was used to predict the current density distribution in the electrodes, raw material, slag and molten metal as a result of the three phase AC current. The effect of the electrode immersion on the current path was studied. The ?proximity effect? caused a pronounced asymmetry in the electrode currents in the circular furnace, whilst the electrode currents in the rectangular furnace exhibited radial symmetry. The current distribution in the melt in both furnaces indicated that the bulk of the current flows between phases. The current density is greatest between electrodes. Results were compared to qualitatively similar published work, operating experience and results of furnace dig-outs.

Jan 1, 2007

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications.

Jan 1, 1963

By Thomas A. Simpson

Traveling through the moors and valleys of Cornwall, England, one is reminded of the extensive mining activities of the past. Abandoned shafts, remains of granite block wheel houses and engine houses, battered brick stacks, old calciners, overgrown water wheel pits, count house remains, overgrown waste pits, and old portals are gaunt monuments to a once flourishing mining industry. Cornwall is bordered on the north by Devon and occupies the south-western most tip of Great Britain. The Atlantic Ocean borders the promontory; to the north, the mouth of the famous Bristol Channel faces the open sea; and to the south, the English Channel separates the land masses of Great Britain and Europe. This part of England is probably the most extensively mined ground in all of Europe. Such great mines as Dolcoath and Wheel Vor, Consols and South Carodan, Levant and Bottalack, remain legendary in the annals of metal mining in the nineteenth century. Many US mining districts hold close ties with Cornwall, Devon, and Wales through ancestors who emigrated from there to work in US mines in the eighteenth and early nineteenth centuries. Their descendants can be found in many major US mining districts, and their terms, expressions, customs, and methods have left an impact on the US mining scene that remains with us today.

Jan 9, 1981