Search Documents

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Thompson D. R, Milton R, Perry K. M A

From the Department for Research in Industrial Medicine (Medical Research Council), The London Hospital; and the De Havilland Aircraft Company:M.R.C. INVESTIGATIONS IN 1936In 1936 the Industrial Pulmonary Disease Committee of the Medical Research Council investigated both clinically and radiologically a group of fifty workers who had been exposed for a number of years to the inhalation of alumina in the reduction factory of the British Aluminium Company. The results are shown in Table 1.They also considered the sickness records of all the workers (Hill, 1936), as compared with those in other parts of the factory (Table 2).

Jan 1, 1945

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By F. C. Gennari, D. M. Pasquevich

With the gradual exhaustion of natural rutile, there has been extensive research into its synthesising from lower-grade titanium minerals. The removal of Fe from pseudobrookite (Fe2TiO5) by chlorination was studied, using both isothermal and non-isothermal thermogravimetric measurements. Correlation of the results obtained from element distribution maps, scanning electron microscopy, energy-dispersive X-ray analysis and phases detected by X-ray diffraction in the chlorinated samples showed clearly two associated processes. First, the pseudobrookite particles reacted with chlorine and iron was removed selectively as FeCl3(g), leaving a solid residue rich in the TiO2 phases anatile and rutile, separated from an inner layer of unreacted pseudobrookite by a distinct interphase boundary. Second, chlorine allowed TiCl4(g) to form in the reaction bed, where it removed iron from the Fe2O3 crystals as FeCl3(g) and substituted Ti through a pseudomorphic reaction

Jun 21, 1905

Open pit mining has considerable damaging effects on the environment of the mining region. These harmful influences have to be controlled during mining operation until mine closure. Different sections of mined land, such as; pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined, have to be reclaimed through treatment of environmental pollution and implementation of a permanent post mining land use (PMLU) after mine closure. Implementation of a permanent optimal post mining land use (OPMLU) is one the most decisive criterion which effects on reclamation procedure, mine closure and their costs. Therefore to define ultimate pit limit (UPL), mine closure and reclamation costs should be entered in the calculation iterations same as the other variable costs of the projects. Estimation of closure and reclamation costs of a mining project is carried out based on the attained OPMLU and the specifications of the mine site. In this paper, a model is developed to provide OPMLU for pit area through fuzzy multi-attribute decision making (FMADM) technique. The model was implemented on a hypothetical copper mine in northwest of Iran as a case study. Lumber production was selected as OPMLU for the pit area. It is finally concluded that through the developed model, OPMLU for different sections of mined land in an open pit mine project is defined. Also closure and reclamation costs are estimated based on the defined OPMLU to achieve a more accurate UPL.

Dec 6, 2010

The paper outlines the history and current status of the VALMIN Code and sets out the background, methodology, results and recommendations of the Independent Review of the VALMIN Code undertaken during 2001 under the Chairmanship of Ian Goddard. The paper is based on the final report of the Taskforce, which was submitted to the Board of The AusIMM for consideration.

Jan 1, 2002

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By A. Adu-Acheampong

A geotechnical study was conducted to identify the cause(s) of stope instability at the Ashanti Mine (Obuasi, Ghana). As part of the investigation, laboratory testing of rock was performed and the rock mass was classified according to the Q-System (Barton et al., 1974).Numerical analyses were performed using the computer program FLAC (Itasca, 2001). The observed failure zone around the stopes was simulated using both Mohr-Coulomb and Hoek-Brown (Sheorey,1997) models. Yielding along peripheral graphite bands and tensile failure were clearly identified to be the major contributors to stope instability.

Jan 1, 2003

By D David

The majority of SAG and ball mill design methodologies are applied using a single design value for mill selection, such as the 80th percentile ball mill work index or SMC value. Inherent in the selection of this design value is a desire for the mill to accommodate unfavourable, but not absolute worst case, feed conditions. It has been observed in numerous “post-mortems” of unsuccessful designs and also in many optimisation studies, that the selection of the design value has been poor. Statistical analysis of testwork data sets shows that inherent variability in the data can, by itself, lead to design errors. Metallurgical testing is an attempt to measure the characteristics of millions of tonnes of ore using only a few kilograms of sample. In this paper some realistic but synthetic test work data sets are used to explore old and new methods of defining the design envelope and subsequently selecting a reliable point. The aim of the paper is to provide practitioners with tools that reveal the adequacy (or otherwise) of metallurgical test programs intended to support various levels of project design. It also provide guidance as to how it is possible to statistically justify a comparatively high design point in the absence of adequate test data.CITATION:David, D, 2015. Measuring and taking notice of orebody variability – an essential ingredient for reliable plant design, in Proceedings MetPlant 2015, pp 10–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By F F. Pitard

The comparison between J Visman and C O Ingamells’ works with P M Gy’s works has been the object of intense debates in the past. Such negative debates inevitably resulted in a loss of many good opportunities. The author’s long experience in applying works of these three authors led to the pragmatic conclusion that it is relatively easy to integrate everything Visman and Ingamells created into the Theory of Sampling; therefore, it is suggested that the compatibility has been vastly overlooked, and a correction for such anomaly is recommended. It is important to emphasise that Visman and Ingamells works may be beneficial and provide relevant, harmonious additions in some areas, and ultimately offer attractive possibilities to sampling practitioners. Such additions may enhance our capabilities to predict sampling difficulties by using a stronger strategy and to design better sampling experiments that would allow us to further understand the heterogeneity of minor constituents, and especially trace constituents. Basically, the suggested integration is essential for sampling trace constituents in the environment, in food, in chemicals and in the pharmaceutical industries.CITATION:Pitard, F F, 2017. Integration of Visman and Ingamells’ works into the Theory of Sampling – a necessity to expand possibilities in sampling practices, in Proceedings Eighth World Conference on Sampling and Blending , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Noel N. Moebs

Valley Camp No. 3 mine was the scene of an experimental shortwall introduced in 1973 in an attempt to improve the recovery from the Pittsburgh coalbed in the Ohio Valley area where adverse ground conditions have imposed partial extraction methods with only 40 to 55 percent recovery of the valuable resource. The Bureau of Mines, under a cooperative agreement with Valley Camp Coal Co., monitored ground pressures and caving in the shortwall section in an effort to determine whether the roof strata, notably the limestone main roof, will cave to the extent that roof pressures at the face are relieved and whether the powered roof supports can sustain the roof load. The Bureau&apos;s efforts included mapping of clay veins, instrumentation of chain pillars and shortwall panels with encapsulated pressure cells, recording hydraulic pressures in the legs of the shortwall chocks, and core drilling underground and from the :surface. The experimental shortwall was a qualified success. Recovery increased 5.4 percent compared with partial extraction. Pressures in chain pillars and the abutment zone were not excessive. Hydraulic pressures in the chock legs did not approach the yielding pressure. Apparently, the limestone strata caved and the roof pressure at the face was relieved.

Jan 1, 1976

By T. Lindstad, S. Gaal, S. Hansen, S. Prytz

The SINTEF SiO-reactivity test, developed by Tuset and Raaness in the 1970?s, is a recognised method of characterising the ?reactivity? of carbonaceous reactants, used in the ferrosilicon and silicon metal industries. Recently, the test has been updated, which has resulted in the development of an extended and improved SINTEF SiO reactivity test. This has included updating the test reactor, control system, data-logging, handling and preparation of carbonaceous materials to be tested and measurement procedure. The scientific basis has been re-assessed, resulting in a new interpretation of the test results. The repeatability of the test has improved significantly, especially through system automation. In the ?old? test, the kinetics of the reaction: SiO(g) + 2C(s) = SiC(s) + CO(g) for a specific carbonaceous material was characterised solely by the ?R10? parameter, the volume of SiO(g) which passes un-reacted through the coke-bed as the concentration of CO in the outlet gas decreases from 18 to 10%. As both the kinetics and obtainable conversion of SiO to SiC for a reductant is of importance to the ferroalloy producer, the new SINTEF SiO reactivity test ranks carbon materials both according to degree of conversion and reaction rate. From research carried out on the test in the past couple of years at SINTEF and NTNU, it has also become clear that some of the reactions taking place in the test reactor are more complex than previously assumed. As an example, it was previously assumed that the condensation reaction of SiO gas in the condensation chamber of the test reactor can be described as: 2 SiO(g) = Si(l,s) + SiO2(s). However, it has been established that the side-reaction: CO(g) + 2Si(l) = SiC(s) + SiO(g) causes approximately 10% of the total volume of CO to react to SiC and SiO2 in the condensation chamber. This means that some back-reaction i.e., the reverse SiO-generator reaction 3SiO(g) + CO(g) = 2SiO2 + SiC also takes place in the condensation chamber. In the new SINTEF test, the %CO versus time curves are therefore corrected in order to describe the effect of the reaction between SiO(g) and C(s) studied i.e., SiO(g) + 2C(s) = SiC(s) + CO(g). A correction-formula for this purpose is presented.

Jan 1, 2007