Search Documents

The sulphides can be arranged in a series determined by the relative amounts of ionic and covalent bonding present. This series is similar to the paragenetic series common to most sulphide ore deposits. Investigation of the surface tensions of the corresponding heavy metal iodides by the maximum bubble pressure method throws some light upon this relationship. It is shown that the surface tension of molten iodides decreases as the chemical bonding within them becomes more covalent. These results are interpreted in terms of the constitution of the melts, and are extended to cover the case of sulphides in solution in a silicate melt. It is concluded that sulphides tend to lower the surface tension of silicate melts and that this tendency becomes greater as the bonding within the dissolved sulphide groups becomes more covalent. A possible relationship between this conclusion and the origin of paragenesis in sulphide ore deposits is indicated.INTRODUCTIONIt is well known that the order of deposition, or paragenesis of sulphide minerals is remarkably similar in hypogene ore deposits throughout the world. This widespread similarity points towards the operation of some fundamental process which must be intimately connected with -the genesis of these ores. A correct interpretation and understanding of the causes of paragenesis in sulphide ore deposits would shed much light on the origin of these deposits.In Table 1 a simplified paragenetic series for sulphide minerals is presented. In most cases, only the most important sulphide of any particular element has been included. The object of this procedure is to simplify the following discussion. Furthermore, it should be realized that this series is only a generalization and that exceptions and reversals of position are quite common. Especially does this...

Jan 1, 1956

These proceedings consist of an introduction and four descriptive papers. The first paper is an update on fire protection for large haulage vehicles, the second paper is concerned with improved visibility systems for large haul- age vehicles, the third paper is on improved ladders for large haulage vehicles, and the fourth paper is concerned with large haul-age vehicle operator training systems.

Jan 1, 1980

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By Michael Taylor, Thomas W. BoBo

Currently two of the most important characteristics of construction aggregates are (a) the particle size distribution (psd) and (b) the “shape” of the aggregate particles. The long established test methods and standards for these properties require substantial resources and most suppliers can take samples and conduct tests at intervals measured in days (psd) or even months (shape). Furthermore these tests require time: so the results are available only after material has been stockpiled or shipped. In the rare cases where problems are found the out-of-spec material has often been shipped to points unknown. There are substantial advantages to be obtained if the psd and other geometrical properties could be obtained from the material as it moves through the production processes and if the results could be reported back within seconds or minutes to Plant Control Managers. This paper describes a single on-line system used to evaluate production of crushed material in a production quarry. The system consists of an enclosure (containing the camera and lighting etc.) mounted over a production belt. Images are fed by fiber optic cable to a nearby control room where the data are analyzed; stored; displayed; and made available for integration into a process control system. Numerous forms of display can be created according to the needs of the producer. Once programmed by an automation engineer all functions of operation are fully automated. The system has permitted over 400 tests per hour with a feed back time less than 2 seconds. Sufficient geometrical measurements are made so that many different “shape” factors can be computed on a similar time scale. The paper summarizes the results from approximately 100 shifts of about 8 hours each and compares the imaging method with the current standard hand methods. Study of the data generated showed that, when combined with additional plant information, the system can be used to generate additional useful control information.

Jan 1, 2005

The Performance of Benzyl Arsonic Acid as a Collector in the Flotation of Wolframite and Cassiterite Slime

Sep 13, 2010

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

By K. S. Kalenchuk

Massive landslides display complex deformation processes. For instance, slope movements of the Downie Slide, monitored using borehole inclinometers, extensometers, and survey monuments, show considerable spatial and temporal inconsistencies in the displacement rates. This study assesses the influence that inferred shear surface geometry, as a key factor contributing to variable slope movements, has on resolving spatially discriminated slope deformations in three-dimensions. Borehole data defines the shear surface location at discrete points within the slide and therefore, the shear surface geometry for the extent of the slide must be largely inferred. A series of three-dimensional numerical simulations have been run to assess the effect of different interpretations of the shear surface geometry. This investigation illustrates the importance of rigorous geospatial definition of slip surface geometry and the value of three dimensional modelling.

May 1, 2009

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By R. A. Pyper, J. L. Hendrix

Laboratory leaching experiments were conducted to ascertain the effectiveness of acidic solutions of thiourea, CS(NH2)2, for dissolving gold from finely disseminated gold ores. The ore tested was from the Chipmunk ore body of the Northumberland mining district in Nye County, Nevada, USA. Extractions of up to 90% were attained from the ore. Extraction was shown to be dependent on thiourea concentration, ferric sulfate oxidant concentration, acid concentration, and leaching time. Optimum conditions were an ambient temperature leach near pH 1.0 utilizing 100 to 200 kg/ton thiourea and 50 kg/ton ferric sulfate for 8 to 24 hours.

Jan 1, 1981

By Steve Colburn

The new CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, new Windows-based interactive software program, which can be run on any standard PC.

Jan 1, 1995

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

There is a lack of information concerning the movements of water on the continental shelf, particularly with regard to data obtained regularly over significant periods of time. The Horace Lamb Centre for Oceanographic Research has recently deployed data acquisition systems on the sea bed off the coast of South Australia to record tides, swell, and ocean temperatures. Some of these early records are described. The swell data are pertinent to future offshore operations with drilling rigs, barges, and other equipment, while the temperature variations give evidence of significant bottom currents, apart from those due to swell.

Jan 1, 1971

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

"Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape of an organization. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called 'landmarks'), how well they are aligned to support a particular type/nature of innovation in the organization (e.g. radical vs. incremental innovation), and to identify possible gaps between actual and sought performance.The landscape covers four domains that influence innovation - the attributes of the individual, the organizational context in which he/she functions, the business environment (the market / industry in which the organization is operating) and the external environment. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a self-appraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization's particular innovation strategy and environmental context."

Jan 1, 2003

By S. M. Carpenter

In response to the FY2008 Consolidated Appropriations Act (H.R. 2764; Public Law 110?161), the United States Environmental Protection Agency (USEPA) issued the final Mandatory Reporting of Greenhouse Gases Rule (MRR). The rule, signed by the USEPA Administrator, Lisa Jackson, on September 22, 2009, requires reporting of greenhouse gas (GHG) emissions from large sources and suppliers in the United States, and is intended to collect accurate and timely emissions data to inform future policy decisions. The MRR will go into effect on January 1, 2010, and a report of the total emissions for calendar year 2010 will be due to the USEPA by March 31, 2011. Under the final MRR, suppliers of fossil fuels or industrial greenhouse gases, manufacturers of vehicles and engines, and certain facilities that emit 25,000 metric tons or more per year of GHG emissions are required to submit annual reports to the USEPA. The gases covered by the rule are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), hydrofluorocarbons (HFC), perfluorocarbons (PFC), sulfur hexafluoride (SF6), and other fluorinated gases as outlined in Table A-1 of Subpart A of the MRR, which is also provided in Appendix A of this report.

Jan 1, 2011

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008