Search Documents

By T Christie, A Swain

Patterns of quartz veining in epithermal gold-silver deposits at Wharekirauponga, Neavesville and Ohui in the Hauraki Goldfield, have been analysed to determine the effects of different lithologies on vein distributions. At Wharekirauponga, quartz veins are hosted in rhyolite and minor andesite, with the andesite containing slightly higher gold grades. Local basement andesite, rhyolitic tuff and silicified black shale host gold-bearing quartz veins at Neavesville. At Ohui, quartz veins are hosted in rhyolite, rhyolitic tuff and andesite. Fractal analysis was used to quantitatively describe the distribution of veining. The fractal dimension (D) of veining in silicified tuff is 0.25, moderately silicified rhyolite has D = 0.23 - 0.26, clay-altered andesite has D = 0.3, strongly silicified rhyolite has D = 0.3 - 0.39, silicified andesite has D = 0.4, and silicified black shale has D = 0.43. The D values are related to the composition of the host rock, and appear to be controlled by its competency. Hydrothermal silicification results in increased competency and higher D values. Vein thickness frequency plots for different lithologies show that andesite at Ohui, and to a much lesser degree at Wharekirauponga, contains more thick veins than rhyolite and tuff. Gold grades show a strong to fair correlation with higher vein density in three drillholes at Wharekirauponga. The fractal dimension of veining is an important control on fluid flow and gold deposition within an active epithermal system. Vein systems with higher D have a greater density of veining which would have favoured increased fluid-rock interaction. Lower D vein systems have more clustered arrays. The increased fluid-rock interaction induced by a high D vein system, when combined with a reactive host rock, results in an environment which is highly favourable for gold deposition. This situation is seen in the andesite at Wharekirauponga.

Jan 1, 1994

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999

By S. Don Brown

Between 1987 and 1988, the Bureau of Mines studied the mineral resources of the White River National Forest and part of the Arapaho National Forest to appraise the resources present and to determine the types of deposits, and their location, that could be mined economically if sufficient demand and metal prices existed. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. Mineral resource information indicates that in the Gore Range the area between Tennessee Pass and Gilman may contain large base-and precious-metal deposits, and could be the focus of exploration activity in the near future. The Breckenridge mining district was found to have a moderate to high likelihood for mineral exploration and possible development of gold. Recent exploration and minor development work has occurred in several other areas: Montezuma, Kokomo-Tenmile, and Upper Blue River districts, and portions of the Sawatch Range. Limestone, marble, sand and gravel, rock for crushed aggregate, and other industrial rocks have been recently mined or Quarried in the Forrest, and will likely be mined or quarried in the near future. Currently coal is being produced at one mine in the Forest, and extensive identified coal resources are located in the Forest. Parts of four known gas fields lie within the Forest west of Glenwood Springs; there is current production at one field.

Jan 1, 1990

By R. G. Peluso

Methods and results of studies to determine friction and shock losses encountered in auxiliary face ventilation systems utilizing flexible, spiral-reinforced ventilation tubing are presented. The results, tabulated in graphic form, simplify fan selection and enable mine operators to design adequate auxiliary ventilation systems. Problem illustrates the use of graphs.

Jan 1, 1968

By D. C. Goldring

Many high-grade iron ores are considered to result from the supergene enrichment of banded iron formations. The secondary processes may be related to either present-day or ancient erosion cycles and may reach a considerable depth. Other high-grade ores hosted by banded iron formations are regarded as either sedimentary or metamorphic in origin although often also subjected to the secondary processes. The evidence for this multiplicity of origins is reviewed with descriptions of selected deposits: Kedia d'Idjil and M'Haoudat in Mauritania, Bomi Hills and the Nimba Range in Liberia, the Itabira district in Minas Gerais, Brazil, and El Pao in eastern Venezuela. Emphasis is placed on the recognition of textures that show that some ores are tectonites, the precursor materials having undergone pervasive deformation accompanied by metamorphism. The question whether such ores are pre- or syntectonic is difficult to resolve, the evidence being inconclusive, but a diagenetic/early deformation origin is preferred. The possible range of origins has to be taken into account in exploration, particularly as regards the depth of drilling, and in the characterisation of ores for metallurgical use

Jul 1, 1991

By D Hill

In the Ngakuru area zeolite deposits occur in late Quaternary lacustrine vitric tuffs of the Ngakuru Formation and two of the deposits are being mined. The Ngakuru Formation overlies the Ohakuri Ignimbrite dated at c. 240 ka, and is overlain by younger alluvial sands and gravels. Individual zeolite deposits contain 50 - 80 per cent zeolite over a thickness of up to 45 m in thinly stratified vitric tuffs and are localised along NE-trending normal faults. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, Kfeldspar and smectite are also present. The zeolites and other minerals are very fine grained (<10 8m), with open meshes of crystals that result in high porosities (52 - 70 per cent) in mordenite-rich tuffs. Zeolitic tuff samples typically have cation exchange capacities of 80 to 110 meq/100 g and internal surface areas of 25 - 58 m2/g, which combine to give high liquid and odour absorption capacities. The first zeolite deposit (Mangatete) was found in 1992, and this and the Twist Road deposit are worked by quarry benching into the side of hills. The zeolitic tuffs are dried and crushed to produce a variety of products including adsorbents for soaking up oil/chemical spills and animal wastes, animal feed supplements, water treatment, and sports turf and slow release fertiliser. The Ngakuru zeolite deposits formed at shallow depth (<100 m) along fault zones from reaction of glass-rich tuff beds with groundwater-diluted geothermal water during the late Quaternary, and are as young as 8500 yr BP from 14C dating of plant material in sinter associated with the Mangatete deposit.

Jan 1, 2005

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973

By Unknown

More than 60 years ago Lakota (Sioux) Chief Henry Standing Bear asked Korczak Ziolkowski to create a monument of Crazy Horse in the sacred Black Hills. Today, you can see Standing Bear’s dream has grown into enormous reality. Crazy Horse Memorial, mankind’s largest mountain carving in progress, is being carved in the round and when completed will be 641 feet long and 563 feet high. Crazy Horse is only 17 miles from Mount Rushmore National Memorial, giving South Dakota unique boasting rights for having two extraordinary mountain carvings in such close proximity

Jan 1, 2009

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By Isabelle Lamb, Manfred K. Lechner, Daniel N. Adams

Sydney Australia’s M5 East Motorway connects southwestern suburbs to the airport. Central to the project are twin 3.8 km roadway tunnels which are mostly driven through rock. In order to come up with the winning tender, the project team developed several unique approaches for tunnel excavation and support. The project’s flat roof with thin shotcrete lining, 20 m wide underground intersections, thixotropic-grout sheathed rockbolts and cablebolts, and new shotcrete testing methods all differ significantly from traditional concepts. This paper presents the design basis and construction methods used to achieve the 100-year design life required by the project’s owner.

Jan 1, 2001

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By J. N. Van der Merwe

The principal goal of the research described in the paper was to determine, by measurement of pillar scaling on pillars that have not failed, whether the pillar life prediction method developed by van der Merwe (2003) was valid as it stood or whether adjustments were necessary to the rates indirectly derived from observation of failed pillars. To this end, measurements were taken on over 350 pillars at 13sites on 6 mines. The project was done as a collaborative effort between the University of Pretoria, the Nancy School of Mines and CSIR Miningtek. During the course of the investigation, it was found that the majority of pillars display maximum scaling at mid height, that there was no clear preferential direction of pillar scaling, and that pillar corners do not scale significantly more than the mid pillar areas. The most important conclusion was that the scaling rates found by measurement agreed with the inferred rates found in the previous work. The previously developed procedure for the prediction of pillar life spans consequently requires no adjustment, although the error span is in the region of 20%. It is recommended to do further research into the effect of sealing of panels and, possible chemical changes taking place in the pillars as they age on the scaling rate.

Jan 1, 2004

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners' safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

By M Humphreys

Multi-episodic mineralisation is often characterised by different spatial trends exhibited by different generations of the mineralisation. The structural complexity of mineralisation together with the heterogeneous nature of the mineralised zones prevents unambiguous application of the conventional deterministic methodology for 3D constraining of the mineralised domains (ie conventional wireframing is ambiguous).A different approach, discussed in the present paper, includes a probabilistic definition of the domains encompassing one statistical population of the data. The domains are defined geostatistically using the indicator probability model. An indicator threshold is chosen for the definition of the high and low-grade domains. The spatial distribution of this indicator is then modelled by a variogram. The probability of exceeding the given grade threshold is than estimated by ordinary kriging for each modelled block. Blocks are then grouped according to their probability of exceeding the threshold and a continuous closed volume (domain) created from this likely patchy grouping using an appropriate structural model to fill the gaps). Methodology for the geostatistically assisted domaining is discussed in the paper. It is suggested that this technique represents an additional tool facilitating a structural interpretation of the mineralised zones.After the geostatistical domaining of the lode has been completed the grade within each of the domains is modelled using Uniform Conditioning method. Application of Uniform Conditioning for modeling the grade distribution has a significant advantage over linear methods (such as inverse distance or kriging) because Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density and are unable to be estimated directly.

Jan 1, 2002

By John Organiscak

A majority of continuous mining machines employ a water spray system and a machine mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays, and scrubber airflow on dust and gas levels while using a 12.2 m (40 ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1 m (20 ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complemented the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut as compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010