Search Documents

By Stephen Gerard Sawyer

This report presents a Fortran IV computer program for the structural analysis of space-frame protective canopies used in underground mines to protect equipment operators from falls of roof, face, or rib. This program entitled CANOPY permits rapid calculation of the elastic strength of a canopy for a variety of static loading conditions. Stresses in, and displacements of each structural member are computed and printed out. Additionally, identification of all members that have commenced yielding, weight of the canopy, total loads on the canopy, and maximum loads that the canopy can sustain elastically are output. Program description, input instructions, program listing, and two example problems are included.

Jan 1, 1972

By T. S. Washburn

THE grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure-killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes are not present. Also, the rimmed ingot has no well defined pipe, as com-pared to the deep pipe on the killed ingots, and there are numerous pri-mary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differ-entiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7-as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined or deep as in the killed ingot of Fig. 1. In killed ingots, pri-mary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By Frank Johnson

Between 2000 and 2006, platinum production from the South African mines expanded from 206 to 307 tonnes (DME, 2007). Most of this additional metal has come from traditional ?narrow? reef stoping, generally taken to mean stoping in working places with a mining height of less than 1,5 metres. It is well known that narrow-reef stoping presents safety, technological and ergonometric challenges (Pickering, 2007). In planning for the expansion, which is still continuing, the platinum mining industry realized that it could not simply continue with traditional methods of narrow-reef mining. Particular issues identified were: ? High labour-intensivity: caused by use of hand-held rock drilling machines, labour-intensive support installation and stope cleaning; ? Dependence on rock-drillers: this occupation is no longer an attractive one and there is a reducing flow of new recruits; ? Safety: most of the work is performed close to the new faces, where there is the greatest exposure to the hazards of falling rock.

Jan 1, 2008

A Loss of Strength of Gold Sulfide Concentrate Before Grinding and Cyanidation Using Magnetic Impulse Treatment Gold recovery from sulfide concentrates is going with cyanidation usually. The fine grinding to 95 per cent -0.020 mm is required for refractory concentrates, in which gold encapsulated by sulfides. According energy consumption is 10 and more kW h/ton. At this paper we suggested to use magnetic-impulse treatment with small energy consumption 0.1-0.2 kW h/ton for loss of sulfide strength before grinding and cyanidation. The object of studies was the gold-pyrite flotation concentrate which was produced from ores at the Kumtor Mine, Kyrgyzstan. The concentrate composition, physic-mechanical properties and loss of strength mechanism were studied there. The tested concentrate assayed, per cent: 62.5 pyrite, 10 feldspar, 10 mica, 5 quarts, 5 carbonates, 4 haematite and another. Haematite has intimate intergrowth with pyrite ? partially with quarts. The magnetic susceptibility of haematite and less pyrite causes in these grains and mineral complex the effect of magneticstriction. As a result numbers of deformations are increased and minerals and gold are also exposed. Lateral and longitudinal strains in the minerals by magneticstriction were calculated in this work. By quantitative analysis of pyrite mono fractions were showed next micro impurities: alumina, arsenic, nickel and others elements. These micro impurities are generated a charged dislocation, cracks and micro cracks. The inter-granular links at a boundary of haematite-pyrite, pyrite-quarts, haematite-quarts have disintegrated. The dislocation is depended from mineral modulus elasticity. It was determined an indicator of mineral electro-mechanic sensitivity which characterises a conversion of electro-magnetic energy to mechanic energy. Pyrite has most dielectric constant and electro-mechanic sensitivity as haematite and quarts. The dislocations in pyrite are account for clacks and a loss of mineral strength. Size analysis of the flotation concentrate after magnetic-impulse treatment is shown the increasing the content of thin fractions by comparison no treated concentrate. Magnetic-impulse treatment has increased the effect of the next fine grinding too. The electronic microscopy has confirmed a loss of strength of gold sulfide concentrate. The gold recovery by cyanidation increased too after preliminary magnetic-impulse treatment of concentrate by laboratory tests. The magnetic-impulse concentrate studies at the Kumtor plant have showed that a recovery gold increase in the processing of cyanidation. The consumption of energy also reduced.

Sep 13, 2010

By Kelvin K. Wu, George H. Gardner

On July 24, 2002, a nonfatal entrapment accident occurred at the Quecreek #1 Mine, Black Wolf Coal Company, when an active mining section inadvertently cut into a flooded abandoned mine. This incident, and the dramatic rescue which ensued, brought national attention to a common problem in the coal mining industry. Since 1995, there have been more than 100 inundations at coal mines in the United States. Unavailable, inaccurate, or incomplete mapping of older abandoned mines is typically responsible. Serious problems associated with accidental discharges of fluid mine waste material (slurry) and water from coal refuse disposal facilities have resulted from similar causes. Recent problems related to the inaccurate location of old abandoned mine works have increased the interest in the use of conventional and emerging drilling and geophysical techniques for detection of air-filled and water-filled cavities. The United States Congress has committed significant funding toward investigating the applicability of these technologies. MSHA actively promotes the use of the best available technology to minimize the significant adverse safety and environmental consequences associated with unplanned breakthroughs and inundations. This paper provides background information and a general summary of the MSHA-sponsored field demonstration projects which are currently in progress. Potential benefits and limitations are discussed. The need for field verification/ground-truthing is emphasized. Under appropriate conditions, geophysical methods can be effectively integrated into a comprehensive field exploration program.

Jan 1, 2005

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By C A. Locke

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dyke/stock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.  

Jan 1, 1995

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By Stephen P. Signer

To improve the understanding of the support interaction mechanics between grouted bolts and coal mine roofs and to help lay the foundations for improved design and evaluation techniques, the 0.8. Bureau of Mines has conducted laboratory, field, and analytical studies of the load transfer mechanics of grouted roof bolts. Mechanisms by which load is transferred from a bolt through the grout to the rock mass are analyzed. Strain gauges were installed on over 70 bolts and tested to observe the rate of load transfer when a force was applied at the bolt head. Laboratory and field tests were conducted to determine bolt-grout- rock interaction behavior in both the elastic and postyield phases. Long-term laboratory tests were run to determine the time-dependent properties of both polyester resin- and-gypsum-grouted bolts. Numerical studies using finite- element techniques were compared to the experimental results. Elastic tests showed that 90 pct of the applied load was transferred within 24 in of bolt length. Long-term tests indicated that creep is more significant in gypsum-grouted bolts than in resin- grouted bolts. Plastic studies showed that yielding of steel will translate down the length of the bolt from 6 to 20 in.

Jan 1, 1988

By E. Tulcanaza

M.S. Azun I do not at all agree with the basic points of the author's conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey's lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author's paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, I may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [ ] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [ ] The Markovian model for the other second order properties of ReV are also derived. T ve B, in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV's. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semi-variogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 3, 1985

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

Myths and misconceptions regarding cyanide in the mining industry are common. This is not surprising, given the other uses to which cyanide is, and has been put. Unfortunately, the economic benefits, largely due to the introduction of cyanide in towns such as Waihi are often unrecognized. In the current "green" environment, the New Zealand mining industry faces constant scrutiny and challenge. The use of cyanide in hard rock mining is one area which can stir the emotions of the public.   Cyanide can be transported, stored, used and disposed of in a safe manner. The modem mining industry has an excellent record regarding the safety and environmental issues relating to cyanide. Many of the fears relating to cyanide in the mining industry have proven to be unfounded. It is important that this reputation is maintained. This is possible given proactive and ongoing management of cyanide issues.

Jan 1, 1997

By K. Collett

Elandsrand started shotcreting back in 1991. This paper will share the experiences of the mine by looking into the past, the present situation and the way Elandsrand plans to approach the future. It looks at the application of drycrete and discusses the factors that led to the introduction of wet fibre reinforced shotcrete. The logistical constraints of getting shotcrete material underground will be solved by the development of an underground batch plant, using run of mine waste rock as an aggregate.

Jan 1, 1998

By Stuart Brashear, Lee Schettler

The effect of water on several ANFO/emulsion blend ratios are documented by both physical observations and analytical testing to demonstrate the effect even small quantities of water can have on water resistant blends.

Jan 1, 1996

By J Weir

Accurate sampling of slurry streams is extremely important for metallurgical accounting in mining operations, not only for measuring the ore grade from the mine, but also for measuring the recovery of mineral by the mineral processing plant. Accurate sampling is also required for intermediate streams in complex circuits for determining efficiencies of processing units within the plant. As the profitability of the minerals industry is squeezed more with time, greater emphasis is being placed on efficient use of the resource and accountability of the various sections of the mining operations. This has led to increased awareness and interest in obtaining statistically correct sampling across the operations. Accurate sampling is not only required for metallurgical accounting, but is also required for on-line analysis of the slurry streams for elemental analysis and for particle size. Sampling of slurry streams for metallurgical accounting purposes has traditionally been one of the areas of concern in mineral processing plants. In the first instance, the sampler must be designed to comply with the fundamental principles of sampling theory and must provide a representative sample of the slurry stream. In the second instance, the sampler must continue to reliably provide a representative sample, regardless of wear of the equipment or build up of solids with time and other operating issues. To-date the main type of sampler that has been used in mineral processing plants for metallurgical accounting has been the Cross-Cut sampler. These have a cutter that periodically cuts across the full slurry stream. For large flow slurry streams, these are often followed by a secondary and perhaps a tertiary sampler, to reduce the flow-rate or sample, to a manageable size. This paper discusses a new method of sampling slurry streams that has been developed by Thermo Gamma-Metrics, previously known as Amdel Instrumentation. The new samplers overcome many of the problems associated with cross-cut samplers while providing a sample which is representative of the main stream, throughout the life of the sampling system. The sampler is called the SamStat (Sampling Station) and it is now proven in many applications across many countries and mineral processing plants (PGMs, Cu/Au, Pb/Zn, etc).

Jan 1, 2002

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By Juan Lucero

Como consecuencia de los factores externos e internos, las empresas mineras necesitan ser más eficaces a través de la implementación de nuevas tecnologías e informática. En este sentido, la compañía minera Milpo disminuye los costos de hardware para así generar un control de operaciones más minucioso, automatizado y oportuno. Los principales logros obtenidos son el control detallado de las operaciones, los sistemas operativos son la base para obtener los costos operativos, una mejor formulación y control presupuestal, control de servicios de terceros y el de los sistemas integrados.

Sep 13, 2001