Search Documents

By C. M. Young

Bituminous coal piled in heaps or bins frequently undergoes a process of spontaneous heating as the result of the absorption of oxygen. It seems probable that the first absorption of oxygen by coal which has not previously been exposed to the air may occur as a condensation or a combination of oxygen in some form which does not result in the production of carbon dioxide, but slow combustion soon begins. The absorption of oxygen is accompanied by an increase of temperature, and this by an increased rapidity of absorption; hence the dangerous condition proceeds from bad to worse, until the kindling point is reached, unless the process is interrupted. A dangerous rise of temperature can be prevented by excluding oxygen, by increasing the bulk of coal in proportion to its surface exposed, or by circulating enough air to dissipate the heat produced. The storage of coal, in practice, varies from almost complete exclusion of oxygen, by storing under water, to such freedom of access as exists when the coal is stored in open piles. Oxygen available for absorption by coal is supplied by the air in the interstices between lumps and by additional air which may enter the pile through circulation. The size of the coal largely affects both of these supplies; for if the fragments are small the spaces between them constitute a small percentage of the total volume, and little oxygen will be available unless the circulation of air brings in a fresh supply, while with large fragments the percentage is relatively large; circulation also is much easier through a pile of coarse lumps. In the case of lump coal, although a large amount of air may be present, the exposed surface is comparatively small and there is little opportunity for the absorption of oxygen to be so rapid as to cause dangerous heating. Attempts have been made to prevent heating by allowing a sufficient circulation of air to carry off the heat generated; obviously this method cannot be applied to fine sizes nor mixed sizes. When storing coal at the University of Illinois, an attempt has been made to use so much fine coal and to pack it so thoroughly as to prevent circulation of air, while also reducing the original air in the pile so as to prevent heating. This method has been fairly successful, but in some

Jan 1, 1918

By T. C. Clarke

The history of iron construction in this country well illustrates the three phases of thought described by Auguste Comte, the French philosopher. The first is the era of faith, when belief in the safety of structures rests on the authority of the designer. The second is the era of criticism, when plans of structures are analyzed with much mathematical skill, but the data upon which the chain of reasoning depends is assumed upon insufficient experiment. The third, upon which we are now entering, is a scientific era, which demands experimental proof. It also demands that this proof shall be derived from experiments made on full-sized specimens, such as are in actual use, and not upon toy models. Until the construction of the United States testing-machine, now at Watertown Arsenal, it was impossible to make such experiments with accuracy. We now have a machine in which we can test full-sized specimens of every part of a bridge or other structure that we want to use, and under the same conditions in which it is actually used. The next thing is to get money to make these experiments available. No private individuals can afford to do it, and even if they could, they might wish to keep the results to themselves. So that the next point is that we want money, and that, I believe, everybodly thinks we should ask Congress for. We want also, as has been said, some one who shall make a business of testing, and who has plenty of time. Persons who are employed in private business are too much in a hurry; they want to do a thing and get done with it, and then do something else; but government officers are entirely free from this feeling; time to them is of no account, and in experimenting that is the very element that is of value; it does not do to be hurried; the great thing is to get it right and to test your results, and go over it, again and again. And the experimenter who operates the machine must be some person educated up to the use of it. We then want a general advisory board who will indicate a plan of experiments, collect the results; and publish them. Some experiments were made the other day at the Watertown Arsenal upon full-sized

Jan 1, 1882

[Abstmct of remarks by R. II. Sweetser arid suhscqueut discussion at the New York Meeting, February, 1926. The Transactions mill ultimately contain a report of work resulting from these discussions. Need for a standard of ualuration.—There should be an accepted method for evaluating the different kinds of bituminous coals based on their carbon just as that for iron ores is based on iron. Variation in the classes of coals and their desirability fol the different industrial uses is analagous to the case of iron ores. The iron people have developed a standard. In the past coals have not been intelligently distributed because the public has not been informed as to its uses. Many operators have known nothing about the final disposal of the coal shipped from their mines. Sales agents and retailers have had no means of evaluating coals except to make the price as high as the market will stand. Producers and distributors need to know how much more valuable the coals would be if prepared so as to contain less objectionable material. Mr. Swectser cnlletl on the Goal and Coke Committee of the Institnte to organize a study through producers and users to develop a method scientifically and comnereially sound E. A holbrook said that the information exists but the public is unwilling to investigate. He praised Ashley's1 nomenclature of the different kind of coal which has been accepted by the Coal Mining Institute of America and recommended to the American Enginecring Standards Commitee. G. S. Rice pointed out the wider variety and distribution of consumption of coal compared to Iron ore. C'. M. Young approved Mr. Sweetser's remarks and hoped lor a research institution, probably endowed, to study utilization of coal after it comes from the ground. Mr. Sweetser cited incidents to prove his former statements. He said that a reduction of 1 per cent. ash in the coal would cut down the cost of pig iron at a blast furnace 30 c. a ton, that the coal men should tell what the iron men would have to pay to get better coal. H. J. Prryn endorsed the need of blast-furnace operators to know the kind of coal from which their- coke is made and the latler's ash content, as this affects coke consumption. A. C. Fieldncr explained that the difficulty of evaluating coal on the basis of chermical analyses for calorimetric tests is: (1) representativr

Jan 1, 1927

By Charles Legrand

In many iron, coal and copper mines where large tonnages are known before starting operation and proper provisions can be made, the problems of electric traction by trolley locomotives are not very different from those of surface plants. In such installations the gauge of the track, the radius of curves, and the clearances, both vertical and horizontal, can be made to suit the conditions of the traffic. It is more difficult to install electric traction in mines which were started with hand tramming and where no consideration was given to the possibility of mechanical traction being used. The writer having had some experience in the installation of electric traction in copper mines, the following remarks apply more particularly to these mines. With the gauge of track usually 18 or 20 in., the weight limit of locomotives obtainable from manufacturers in this country varies from 3 to 6 tons. The full-load speed varies from 49 to 6 miles per hour. These locomotives, being made to run on very small radius curves, have a short wheel base and a long overhang from axle to coupling, which necessitates a coupling' with a good deal of lateral motion to avoid derailing the cars on sharp curves, especially if couplings are of the standard railroad automatic type. Although 3-ton locomotives will run on 12- or 16-lb. rails, it has been found more satisfactory to use 25-lb. rails, as the track keeps in much better shape, it is easier to maintain the bonding in good order, and fewer derailments from dirt on the track occur with the larger rails. Where 6-ton locomotives are used the 25-lb. rails are satisfactory, but 40-lb. rails have proved cheaper where the traffic is heavy and the ground is soft, as the track maintenance is considerably lower with the heavy rails. The locomotives will run on 15-ft. radius curves, but on through runs it is advisable not to go below 40-ft. radius. The voltage used should not exceed 250 to 275 volts, and the trolley wire should be protected, to prevent accidental contacts, in front of chutes and at all points where it is low. With the air lacking somewhat in oxygen and the heat and high humidity prevalent in many mines, this

Jan 1, 1915

By O. G. Bell

While all of the Southwest Texas fields lie within the Gulf Coastal Plain this area may be divided into three subdivisions—the Coastal Plain zone proper, the Reynosa Escarpment zone, and the interior zone. The Coastal zone includes that strip adjacent to the Gulf of Mexico and . extending inland for a distance of about 60 miles and includes the Palo Blanco, Palangana, Piedras Pintas, Kingsville, Agua Dulce, Saxet, White Point and Refugio fields. The Reynosa Escarpment zone includes a Pliocene overlap over older Tertiary sediments lying west of the Coastal zone. The western margin of the Reynosa formation forms a more or less well-defined westward facing escarpment with which the so-called Reynosa Escarpment fields are indirectly related. These fields include those in eastern Zapata, eastern Webb, western Jim Hogg, western Duval, McMullen, Live Oak, Bee, Goliad and Victoria counties. The interior zone includes these fields west of the Reynosa Escarpment which are not in any way related to it and are on separate types of structure. Production data by fields and wells are shown in Table 1. Roma.—During 1928 the Texas Co. completed two small gas wells at 198 ft. on the Roma Structure near the town of Roma on the Rio Grande in Starr County. This gas is of no commercial importance but was used for fuel in drilling other deep tests on this structure. Three dry holes ranging from 3600 to 4200 ft. were drilled; then their No. 4 Guerra, the fourth deep test, was completed during December as a small producer of 37" Bé. oil from a sand at 3560 to 3590 ft. No production was marketed during December but arrangements were being made to handle the output from this well during 1930. This is the first commercial producer in Starr County. Driscoll.—In 1929, Robert Driscoll discovered gas on his Santa Rosalia Ranch in Duval County while drilling water wells. Two sands were developed, one at 2400 ft. and another at 2936 ft. and several gas wells were completed in each, ranging in volume from 15,000,000 to 40,000,000 cu. ft. and in reservoir pressure from 500 to 1,000 Ib. Early in January of 1929, Mr. Driscoll's No. 14 Fee was completed as a 50-bbl. oil producer at 2894 ft. Two other oil producers were completed early in 1929. Mr. Driscoll's death early in the year curtailed develop-

Jan 1, 1930

By John A. Mathews

D R. CHARLES W. ELIOT, the great educator and philosopher-he of the five-foot book shelf-recently gave expression to a thought I had long been cherishing as a private opinion, when he said: "It is obvious that standardization has become a dangerous adversary of progress in both education and industry." This idea must have been more widespread than either of us knew, for some five years ago a writer of verse for one of the comic papers dealt with it at great length. I will quote only a few of his stanzas to illustrate his understanding of "A Standardized Existence" : A visitor at large, I stand Beneath a standard sky- Where everything is standardized To please the standard eye. Each tree is of a standard height, Each building is the same; Each man is uniform in height, And has a standard name. Above there is a standard star Beside a standard cloud, And a standard weather here prevails To please a standard crowd. With standard joy, and standard gain, The standard people live; And if there is one bit of pain T?is such as standards give.

Jan 1, 1926

By A. F. Frederickson

Rapid advances in any branch of science often follow the development of new instruments or techniques which permit the scientist a closer look at the material in which he is interested. With the development of the polariz¬ing microscope, modern petrology was born. The resolving power of the microscope, however, was not great enough to enable the geologist to dis¬tinguish or identify the material now known to be minerals which constitute the bulk of the rocks known as "clays" and laterites. The discovery of X-rays and the development of powder X-ray diffrac¬tion techniques provided the extra resolving power necessary to get "a closer look" at the minerals in the clays and laterites. These techniques are largely responsible for the great strides made in the past two decades in the identification of the clay, sesquioxide and hydroxide minerals. To obtain an X-ray diffraction. pattern of a mineral or rock is relatively a simple procedure, but to interpret this pattern in terms of crystal structure or min¬eral identity is quite another matter. It has taken the combined talents of physicists, physical and colloid chemists, mineralogists, and geologists to unravel the identity of some of the minerals in these complex rocks and, as this symposium will indicate, many more problems remain to be solved. To assist in the identification of these minerals, we have the ever-useful microscope, which, is supplemented by the development, only in the last ten years, of differential thermal techniques and the powerful and costly "eye" that enables us to see the shapes and sizes of extremely small particles -the electron microscope. To this array of equipment must be added such gadgets as supercentrifuges, spectrographs, and the apparatus necessary for chemical analytical work. Obviously, not only is it difficult for any one man to master all of the techniques to the point where he can do competent re¬search, but also few institutions are able to provide the high capital outlay for purchase and maintenance of suitable equipment. Here we clearly see that if this equipment is to help us solve our many problems, a close co¬operation of specialists from various institutions and industry is essential. This, however, is less than half the problem. If the geologist is going to learn to intelligently find, and the industrialist to intelligently and eco¬nomically exploit the materials that constitute a large part of the mineral wealth upon which our way of life is based, we must get a better insight into

Jan 1, 1952

By T. Sterry Hunt

AT the meeting of the Institute in Easton, October, 1873, I made a communication on the Ore Knob copper mine, in Ashe County, North Carolina (Transactions, vol. ii, p. 123), in which I called attention to the chemical decomposition alike of the pyritous lode and the inclosing gneiss rock to a depth of 60 feet, by which the feldspar of the latter had been converted into clay, and the whole rock very much softened. Such a decomposition is well known to be almost universal in the crystalline rocks of the Appalachians south of the Potomac ; and if it is only seen in rare and exceptional cases farther to the northward, this, as I have elsewhere pointed out, is due to the fact that the decomposition began and ended in the ages anterior to the drift period, and that the decayed portions which still remained were at that time removed from the surface, except in some localities which were protected from the eroding agency. I have lately had an opportunity of studying a remarkable instance of this kind in an examination made last month for the corporators of the Hoosac Tunnel.* The locality is at the western base of Hoosac Mountain, the western slope of which rises rapidly 1300 feet above the town of North Adams, in Berkshire County, Massachusetts, itself 700 feet above the sea level. Through this mountain, as is well known, a tunnel for the Troy and Boston Railroad has lately been opened, a distance of 25,081 feet from east to west. The rock of the mountain consists of mica schist and micaceous gneiss, including in its western half a great mass of harder feldspathic and quartzose strata in part a granitoid gneiss, the strata for the most part dipping to the eastward with variable angles, but with occasional western dips, apparently due to inversion. The crystalline strata of the mountain crest and sides are in many places exposed, and present rounded surfaces, often deeply grooved and striated, but with no appearance of decay. At the western base of the mountain, however, the gneissic rock is in a state of complete decomposition, which was well displayed in opening the tunnel, which, for a distance of several hundred feet, was driven through highly inclined strata so much decomposed that they were excavated with pick and shovel, and without the aid of blast- * See, for a detailed account of this examination, Dr. Hunt's report, published by the General Court of Massachusetts in House Document No. 9, 1875.

Jan 1, 1875

By L. C. Armstrong

A. E. ROSS*—Mr. Armstrong in his paper stated that they had experienced considerable difficulty in drilling the quartz-feldspar intergrowths. The dia-mor~d loss was excessive and the diamond bits polished quite rapidly. Mr. Davidson, who presented the paper, stated that bortx stones in the range of 20 to 30 per carat had been used in the bits on this job. I would like to suggest the use of bits employing stones in the range of 60 to 100 per carat, an average of possibly 80 per carat. If these stones had been used the bits might have lasted longer and not polished so quickly. As a basis for this suggestion I would like to point out that in northern New York State we had at least two examples where bits employing stones in the range of 80 per carat had solved a difficult problem. Bits set with stones in the range of 20 to 30 per carat had been used previously and had failed. With the finer stones, the cost per foot of drilling decreased material1y. It should also be noted from a technical standpoint that the smaller stones require higher drilling speeds than the larger stones. Greater pressures are not normally necessary, and it is the higher speed which seems to be the major factor of importance. It should also be noted that the finer stones afford a greater number or cutting surfaces for the same carat weight in a bit. Then too, the smaller stones, by virtue of their size, serve as sharper cutting edges than larger stones. There is no doubt that the diamond bit employing smaller stones costs more to set than the bit using larger stones. However, with the technique developed at the shops of Sprague and Henwood, Inc., we feel that the relatively slight additional cost required to set these bits is more than paid for by the resultant lower drilling cost. We feel that the highest quality stone available is the most economical to use when hard fine grained rock is encountered. In summary, I would suggest that it might be possible to solve the problem presented in this paper by using a diamond bit employing stones at least as small as 80 per carat of the highest grade possible and by using the diamond bit at the highest speed available with modern drilling equipment. L. C. ARMSTRONG (author's reply) —It is generally agreed that the use of smaller, high-grade diamonds and of higher drilling speeds, as suggested by Mr. Ross, may be the best approach to the solution of the problem.

Jan 1, 1950

By Luther B. Eames

J. V. N. DORR, New York, N. Y.-I have read Mr. Eames' excellent paper on this' subject with great interest, for besides being connected with the design and installation of the first modern countercurrent decantation plant, he was associated with me in the development of the thickener in the Black Hills some years earlier, and has now been operating the largest plant that has used this method of treatment. His, discussion, of the influence of different factors on the results obtained is quite thorough, but several features I think may not be apparent to the reader who has not studied the subject carefully. 1. Grade of Ore That Can Be Treated.-Mr. Eames has shown graphically that' the assay of all solutions increases directly as the grade of the ore treated. He has not emphasized, however, the fact that, as most operators prefer to keep the assay of pregnant solutions down below a certain figure in order to insure complete precipitation, an increase in ore value beyond a certain point means a proportional increase in solution precipitated and therefore not only an increase in the percentage of dissolved gold recovered, but an actual descrease in tailing loss. The importance of the influence of the percentage of moisture in the underflow on loss is made clear, and I. may add that unless it is quite evident that pulp can be safely settled to 50 per cent. solids, or more, it is usually advisable to use a continuous filter at the end of. a decantation plant to reduce losses in cyanide and gold. Dissolution in Thickeners.-The influence of a change of solution on silver dissolution has long been emphasized and most gold operators have. recognized the annoying way in which a gold ore after being agitated until nothing more can be dissolved will loosen up again when almost ready for the dump after the dissolved metal has been removed by decantation or filtration. Continuous decantation gives favorable conditions for this additional dissolution and a chance to recover most of what is thus dissolved. This is especially true if an extra tank is used in the series and barren solution added at the second tank from the end instead, of the first, as shown in Mr. Eames' Fig. 1. It can be calculated that the use of this tank will reduce the mechanical loss of cyanide by one-third and cut the gold loss as well; but the saving in gold or silver that may dissolve when the pulp is first diluted with weak solution may be as important.

Jan 4, 1917

By P. Barnes

(Resident Engineer, 1873-75.) SEVERAL statements have been made to the Institute, somewhat detached from each other, as to the cost of some parts of these works, but they have not included any extended description of the. buildings or machinery. The general plan of the work connected with the water supply differs, in some important details, from that which has been common either in the Pittsburgh district or elsewhere, and a somewhat extended description may be of interest to the Institute, in connection with a note of the cost of the work. The plan as a whole, and nearly all the important details, were developed by Mr. William P. Shinn, C.E., the general manager of the Company. The immediate and responsible charge of the work was in the hands of Mr. John C. Lewis, C.E., to whom had been committed all the work of this general description, including the laying-out of the whole of the foundations, the erection of the buildings, and the grading and laying down of the entire railroad system. The continuous operation of the machinery and other fixtures of these waterworks, for more than three years, has fully demonstrated the correctness and economy of the plan adopted. No casualties of any moment have befallen the apparatus, and no improvements have been suggested as important except that the gate at the river end of the conduit should have been made more completely water-tight, so that the whole length of the conduit could be pumped out dry without resort to any temporary dam in the conduit itself. In general terms the works of the Edgar Thomson Company are situated on a plateau, about 52 feet above the low-water level of the Monongahela River, and about 2000 feet from its bank. The site of the works is bordered on one side by Turtle Creek, a small stream which drains a considerable area of coal mining territory. This creek is about 100 feet from the group of buildings which have been erected, but it flows into the Monongahela River at a point, about 1200 feet further up than that selected for the entrance to the water-works conduit. It was ascertained by analysis that the water in the creek contains an important percentage of sulphate of lime, while the water of the river is of unusual purity, in respect of any salts

Jan 1, 1879

By John F. Blandy

With the Report of Mining Statistics, for the year 1872, there was published a geological map of the United States and Territories. This is, I believe, the only map which represents the geology of Arizona, and is, as far as my observations go, correct. It is, however, on so small a scale as to be of little practical value to the miner. I know of no other maps, even of localities, of this Territory. The topographical maps are also on so small a scale as not even to serve as guides from place to place; the largest, that of Eckhoff and Ricker, being only 30 by 30 inches to represent a territory of 135,000 square miles. For these reasons, it makes it exceedingly difficult to describe the various mining centres in an intelligent manner, and equally so to examine such a hilly country as it is intended to describe in this paper. When I first came into this Territory I soon realized the troubles I had to encounter in trying to form an opinion, or even to get the needed information on the geological contour. I have, therefore, labored as best I could to get a topographical diagram of the section of country represented by the map which accompanies this paper.* The lines run by the Land Department up the valleys of the Aqua Frio, and those west of the Hassayampa, and connected east and west to the north of Prescott, enabled me to inclose correctly the space covered by the Bradshaw and Sierra Prieta mountain groups, but the territory covered by these mountains, and the most difficult part, I have had to fill up as best I could. I have met with such success as to meet the approbation of those most familiar with the country, and, with the map in hand, any one would he able to cross it in any direction. As there has not been a single line of survey made across it, this has been no small undertaking, and I have had to depend upon sights from prominent points with the pocket-compass, or, in the absence of that, to make observations, with watch in hand, and guess as near as possible the meridian direction. Rut one main wagon-road passes through the district, that from Prescott to the Peck mine.

Jan 1, 1883

By E. C. Franz

IN an effort to understand high cycle fatigue, as well as to study the mechanism of fracture in general, a number of researches have been undertaken whereby the fracture properties of a metal have been determined under conditions of repeated cyclic prestsain employing high strains with relatively few cycles. Liu, Lynch, Ripling, and Sachs' showed the effect of a definite strain history consisting of small increments of tensile or compressive prestrain upon the flow and fracture characteristics of metals after a limited number of repeated loadings. Liu and SachsW emonstrated by cyclic straining of the aluminum alloy 24s-T4 that the least reduction in ductility was obtained when the compressive stress was nearly equal to the tensile stress. Attempts have been made to correlate the reduction in ductility under such prestraining with conventional fatigue data, as was done by Liu and co-workers.' The following research was conducted to determine if such reduction as has been noted could be correlated with conventional fatigue data or whether the effect resulted from causes extraneous to the basic mechanism of fatigue failure such as strain aging. It might be pointed out in this connection that the reduction in ductility has occurred in alloys that might be susceptible to strain aging or similar behavior, such as alloy 24s-T4. In the present investigation, the test specimens were prepared from the aluminum alloy 75s-T6 and annealed electrolytic copper. Alloy 75s-T6 is a complex precipitation hardenable alloy, whereas electrolytic copper would not be expected to exhibit strain aging effects, particularly at room temperature. The experimental procedure consisted of prestraining test specimens repeatedly by increasing tension in small increments to various total prestrain values, followed by testing to failure in a tension test. The prestraining as well as the final testing was performed on a tensile machine using special fixtures9 0 maintain concentricity of the specimens. After prestraining, the specimens were unloaded as rapidly as possible and immediately reloaded so that the total time lapse between strains was held to a few seconds. Logarithmic or true natural strain was used in all calculations. The results are presented in Figs. 1 and 2. In Fig. 1, the retained ductility, area after prestrain area at fracture is plotted against the tensile prestrain, initial area area after prestrain as abscissa with the number of stress reversals executed to attain the required prestrain plotted as parameter. Several specimens that fractured during

Jan 1, 1955

SMALL things are customarily moulded in two ways (unless they have undercut parts which hold them in the moulds); that is in clay, or with natural or which artificial earthern powder made in halves in either wooden boxes or bronze frames. This also depends on whether the object is larger or smaller. Now if you wish to mould with moist clay, you must grease your relief with oil or pig fat; apply a dusting of charcoal, ashes, or cuttlebone on it; or gild or silver it dry with gold, silver, or tin foil. Then, first make with moist and somewhat firm clay a plate as, thick and large as can conveniently hold your relief, and carefully set the latter halfway into this and let it dry. Then, greasing or dusting it again, make the other half. When both are well dried, take out your relief and at the top make its gates and vents. If plastering is needed, do it. Finally, bake the halves, fit them together, and tie them well, as you wish, using the procedure that I taught you in the discussion of brass. But if one has to make a large quantity of works of one kind, he should for the sake of convenience use the method with powder [120] because it is short and requires less time and expense. Therefore if you wish to do this, you need to have several pairs of bronze frames or wooden boxes, higher than half the relief that you wish to mould, and of convenient length. On a flat board always keep half of one of these frames full of powder that has been slightly moistened for moulding, as I told you, so that by pressing with the ends of the fingers and with the hand it holds together as well as possible. Level it off with a cutting tool and when leveled put a flat board over it and turn it over. Turn it on to a dusting of ashes so that it will not stick, dust it on the other side, and remove the excess by blowing it off Then mould the thing that you wish to mould, pressing it halfway in once or twice, always taking it out and putting it back again. Then the other frame is fitted in its place and filled with earth by pressing and squeezing it carefully. Then it is leveled off on the outside with a sharp tool as you did with the other part, and then one of the parts of the frames is lifted up with the point of a knife or some other tool and,

Jan 1, 1942

By Prince Lazarovich Hrebilianovich

I was asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day's labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman's point of view with the understanding that the industrial employer's effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had not yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man's reason for coming, what grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a 'air deal is all the man wants.

Jan 1, 1918

By Allen Rogers

TWENTY-FIVE DOLLARS for nothing at all except a sheepskin. That to me is the effect of the New York State law for registration of engineers and the same may be said of any of the state licensing laws. Of course, if one has to practice in more than one state, he must pay a more or less equal amount for every state he works in; and yet there has been little effective protest against these laws. It would seem that the spirit which animated the Boston Tea Party is non-existent amongst engineers. Undoubtedly a good many consider, through their failure to understand the law, that the matter does not affect them. In New York State it is provided that "any person practicing or offering to practice profes-sional engineering or land surveying . . . shall be licensed as hereinafter provided." To quote further from the law: "A person practices professional engi-neering . . . who holds himself out as able to do, or who does, the work that an engineer does . . . " The cunning of the wording of this article can only be appreciated by considering that anyone calling himself an engineer falls within the definition; its liberal inter-pretation (I have not quoted the whole of it) would embrace many who do not consider themselves engi-neers. The state authorities may not construe it to include such individuals; indeed, they may possibly consider it inexpedient to extend it to include engineers of subordinate grade, but the possibility is always there and, even though an engineer be of the grade of assis-tant, he may at any time be called upon to substitute for his principal in responsible charge of the work. It is therefore clear that anyone calling himself engineer and practicing engineering must, for his own protection, apply for registration or run the risk of violating the law. Now, what is the sense of all this? We have done very well without such restrictions on the means of gaining our livelihood. If one only stops to think, there is hardly a minute of his modern existence when he is not dependent for his safety on the engineering by engineers of yesterday or today. How often is one in jeopardy through failure of engineering works, work done under the supervision of those same engineers? If all of us had to wait for our ends by such means, our average life would probably be some thousands of years. Where, then, is the point to the object declared in all these laws that the need for licensing is "to safeguard life, health and property?" Bosh!

Jan 4, 1923

By W. P. Ward

I desire ho put on record a fact in relation to the effect of man ganese on pig iron which I have never seen in print, and which may, perhaps, not have been observed by anyone except myself. In 1875, while experimenting on the production of ferroman ganese in a blast furnace, I had burdened the furnace with a charge which I calculated would produce a 15-per cent. spiegel. The fur nace was very hot, having been running for a couple of days on a very light burden, and making a burnt iron, preparatory to the experiment I proposed to make to produce a high grade of spiegel. I calculated that the charge would begin to work in the fur nace in about twelve hoars after it was put on. After the -lapse of that time I commenced to watch the furnace carefully, but found little or no change in the appearance of the metal, although there was a very decided change in the cinder, showing that the man ganese ore had come in work. The iron was quite gray and very tough. The character of the cinder was good for a spiegel cinder, and 1 could not imagine where the manganese was going to, as it (lid not appear to be in either metal or cinder in anything like the quan tity indicated by the charge. The next morning things were still in the same condition. The furnace was very hot, the cinder good, and the iron very gray. I was then sorely puzzled. I had never heard of a gray iron with over 4 or 6 per cent. of manganese, and had no notion that an iron with more manganese could be gray and tough. With great difficulty a piece for chemical test was broken from a pig. Not less than a hundred blows from a heavy sledge were required to break it off, I took the specimen to the shop and directed that some borings from it should be brought to the laboratory, as soon as possible, whither I myself at once repaired to put things in readi ness for a rapid manganese determination. In about half an hour the machinist came in with the iron specimen in one hand and about a dozen blunted and broken steel drills in the other, saying that it mas impossible to drill the iron. There were several little depressions in the iron, which was malleable enough to be indented by the point of the drill, but not a chip had been cut from it. The metal was never subjected to further physical tests. A chip broken from

Jan 1, 1882

By Leonard D. Jaffe, Donald C. Buffum

THE importance of temper brittleness in alloy steels has long been realized in Europe, In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. INTERPRETATION OF PREVIOUS DATA For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.1 One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 450-550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness, If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2,3 found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.4-6 The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture, If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1948

COLLECTIVE bargaining, hereto-fore loudly proclaimed as one of the stout timbers of the Republic, has passed from the picture. The coup de gr[a]ce was struck by the President of the United States when he ignored his vested legal prerogative and seized the steel industry by the dubious authority of, his "inherent powers." Autocratic judgment by a single official replaced arbitration by the steel industry and labor union. This is the outcome of a battle which has been bitterly waged for months in the hazy atmosphere created by well oiled propaganda machines. Prior to government intervention, there was no clear picture of the issues at stake. All parties concerned marshalled their accountants to conjure up figures proving their respective contentions. The results were fed into public relations departments for embellishment and dissemination. Thus, the public was asked to believe on one hand, that the steel worker, who is second only to the coal miner in hourly wages, was entitled to an increase in pay and other benefits. Nothing was said about the effect-of such an increase on the national economy. Industry in turn pointed to declining profits after taxes, but failed to mention the more than a billion dollars spent on plant expansion, in addition to the payment of substantial dividends for 1951. With the intervention of the administration, the immediate issue became clear to freedom-loving Americans. Is the executive branch of the government above the law, or is it supposed to uphold and carry out the .laws of Congress? The present administration forgot that it is a servant of the public and has become despotic. The American people must obliterate this dangerous precedent which has been set by the administration or accept the. ominous consequences of submission. Fortunately, the strongest weapon of the citizen-the ballot -still remains. When democratic procedure is restored, stabilization of the economy will continue to challenge us. This is the main public stake in the steel controversy. Only a solution based on bed-rock democracy will work. If the emergency is real, and we must assume that it is, this is the time for sacrifice. Industry and labor must meet without rancor to resolve wage contracts through collective bargaining. The government role, under emergency conditions, must be to objectively maintain wage, and price ceilings in the interest of stabilization. Political expediency cannot be permitted to' influence these controls. Politics and not the public weal have been the guide lines for too long. We are at the cross roads. By all sober judgment, this is the time for Americans to take a militant interest in their government today. Tomorrow will be too late.

Jan 1, 1952

By E. C. Harder

J. T. SINGEWALD, JR., Baltimore, Md.-I might say a word further in regard to the Miguel-Burnier district. I am sorry Mr. Harder is not here. I had hoped to be able to ask him a few questions in regard to some of the features of those deposits. This Miguel-Burnier district is the other district that I referred to that lies in the State of Minas Geraes. The interpretation that Mr. Harder gives to, these deposits is the same as that given by Harder' and Chamberlin in a previous paper, and that is that they consist of lenticular deposits of sedimentary origin in a series of rocks that also include lenses of limestone, but they seem to think that the manganese ores occur at a definite horizon and at a horizon different from the limestone. We found that the manganese ores occur at several horizons, as also do the limestone lenses, and the limestone masses are of the same shape as the manganese orebodies, so that our own feeling was that these manganese ores simply represent concentrations within the zone of oxidation formed as. a result of decomposition and replacement of this limestone. To the east of Miguel-Burnier there is a big bend in the railroad which cuts through, at right angles to the strike, this series of rocks. Here is shown very well both the local character of the limestone lenses and the local character of the manganese lenses in that, though the distance across the bend is only a couple of hundred yards, the limestone and. ,manganese lenses do not match up at all, and it also shows plainly that both occur at more than one horizon.. Consequently there is no reason why the manganese ore could not represent alterations of this limestone. The mine workings do not as yet give very definite information on this point in that they are all comparatively shallow and within what would be the zone of oxidation so that what they will grade into below that depth, we do not know. On the other hand, the character of the ore suggests that it may, represent such -a product in the zone of oxidation in that it tends to be quite earthy; whereas, if the manganese had been there originally as such it would have undergone the same metamorphism that the other rocks have undergone and one would have expected that it would have been converted into a hard manganese ore that would today stand out pretty much as do the iron ores of that same region and not have the soft, earthy texture which is a prevailing characteristic.

Jan 4, 1917