Search Documents

By H. M. Dess, S. R. Bolin

A modifiedl Czochralski technique has been utilized to grow single crystals of YVO, pure or doped with europium or neodymium, from 1 to 2 in. long and 4 to 1/2 in. in dianz. An oxyhydrog-en gas-fired furftace zuas used in this ulork, and melts were contained in iridium crucibles. Successful application of the Czochralski ~vzethod was found to depend upon atmosphere control to prevent crusting and to limit melt decomposition, the establishment of symmetrical thermal gradients in the melt to obtain stable growth, and the selection of high-quality single-crystal seeds to prevent propagation of misorientations during growth and subsequent catastrophic cracking. The suitability of YVO4 as a host for laser-active trivalent rare earth ions has long been recognized. However, the problems associated with the growth of sufficiently large, good-quality single crystals have, until quite recently, seriously hindered satisfactory evaluation of the laser potentialities of this material. Both flux growth and Czochralski growth techniques were investigated at an early stage of interest in YVO,. The former method proved incapable of yielding crystals large enough for practical use,ly2 and the latter was beset with difficulties which took some considerable time to understand and overcome. Recently, however, the Czochralski growth process for YVO, has been improved along separate but similar lines of development by groups working independently in the Crystal Products Department of Union Carbide's Electronics Division and Bell Telephone Laboratories3 so that now good-quality single crystals of satisfactory size can be produced on a routine basis. Stimulated emission from a neodymium-doped YVO4 crystal grown by the Crystal Products Department of Union Carbide was obtained by O'connor4 of MIT, Lincoln Labs. An oxyhydrogen gas-fired furnace was used in this work, Fig. 1, and melts were contained in iridium crucibles. The starting material was 99.9 to 99.99 pct pure YVO4 powder purchased from the Chemical and Metallurgical Division of the Sylvania Electric Products Co. Typical impurity levels, determined by spectrographic analyses, were as follows: Si, 50 to 500 ppm Al, Fe, Mg, 5 to 50 ppm Ni, Pb, Mo, Mn, Ce, Cs, 1 to 10 ppm Initially, YV04 powders predoped with neodymium or europium were obtained from Sylvania. Later, however, because of a desire to grow a series of crystals containing relatively broad concentration ranges of these dopants, it proved more convenient to start with pure YV04 and mechanically admix Nd2O3 or Eu@~ powders plus equimolar amounts of V2O5. The empty crucibles were preheated to 1900" to 1950oC, a temperature range where melting occurred readily. The powdered YVO4 feedstock was then added incrementally. However, a marked tendency toward

Jan 1, 1968

By Donald T. Hawkins, Ralph Hultgren

The lorsion effusion method has been used to measure the vapor pressure of lead over pure lead and eight Pb-Sn alloys ranging from 9.1 to 87.9 at. pct Pb in the temperature range 950° to 1125°K. The resulting ?H°y 298 = 46,630 ± 200 cal per g-atow for pure lead is in excellent agreement with previous work. Deriued ?Gph values for the alloys were smoothed and correlated with previous heat of formation data to obtain entropies for the liquid alloys. values for the tin component were calculated by Gibbs-Duhem integmtion. Surfhce depletion of these liquid alloys was found to be absent, as shown by the fact that the measured pressure remained substantially constant with time in contrast with previous measurements on iron-rich solid Fe-Mn alloys. The activities and Gibbs (free) energies of the liquid Pb-Sn system are not well known although the heats of formation have been accurately determined by K1eppa.l Vapor pressure determinations of the activity of lead by Voronin and Evseev2 disagree with those of Predel.3 Elliott and chipman4 measured activities by the electromotive -force technique in the ternary Pb-Sn-Cd system. From the resulting values of the activity of cadmium, they were able to calculate the activities of lead and tin for the binary Pb-Sn system at the compositions xsn = 0.33 and 0.67. Atarashiya, Uta, Shimoji, and Niwa5 determined the activity of tin from Hz-H2O equilibrium measurements, but their results are subject to question due to uncertainty in the final state of their samples. To resolve these differences, measurements of the activity of lead were made using a torsion-effusion apparatus. Among other advantages, this apparatus rapidly detects errors caused by surface depletion, which tends to reduce the apparent vapor pressure of the more volatile component. If the measured torques remain nearly constant with time, only bulk depletion is occurring. This contrasts with the rapid decrease in torque found in solid Fe-Mn alloys at high temperatures and low manganese contents.6 EXPERIMENTAL 99.999+ pct Pb was obtained from the American Smelting and Refining Co. and 99.999 pct Sn from Vulcan Detinning Co. Eight Pb-Sn alloys were prepared by melting together weighed amounts of the pure metals in evacuated Pyrex tubes and quenching the melts in water. Loss of weight in preparation was less than 0.02 pct in all cases. The effusion cells were made from high-purity, nonporous graphite. Graphite was chosen because of its resistance to reaction with lead and tin and because it can be accurately machined with precision orifices. Two cells were used with overall dimensions as shown in Fig. 1. The orifices of cells 1 and 2 were, respectively, 1 and 1.5 mm in diam.

Jan 1, 1968

By R. S. Moehlman

IN recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. COST OF DRILLING Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 50 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $1 per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft., as more time is consumed in pulling rods. 3. Cost of preparing drilling stations, getting air underground to stations, etc. 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objectionable to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for e5cient hand picking. At most mines an attempt is made to - remove the visual impurities at one or more of the following places in the surface plant: (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors; (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft. in width, so that a picker on either side will be able to remove impurities from the center of the table. Guards usually are placed at the side of the screen, boom or table, to allow the pickers to stand close enough to remove the impurities without too long a reach.

Jan 1, 1950

By R. E. Miner, J. K. Jackson, T. L. Wilson

THE nature of the decomposition reactions producing hardening in aluminum-rich A1-Ag alloys is now fairly well understood. The silver is not uniformly dispersed even at temperatures above the solvus line: rather, it is clustered into zones and associated with dislocations.' During quenching, nearly all of the silver segregates into zones' and some is attracted to dislocations, producing stacking faults. Growth of these faults produces the semicoherent y precipitate.1 During aging, the larger zones and the y precipitates grow at the expense of the smaller zones. The large zones persist up to about 350°C; where they redissolve in favor of the y' and y precipitates.' The equilibrium hcp y precipitate occurs both by a cellular reaction at the grain boundaries1 and by growth of the Y' plates to a critical size where incoherency results. Damask and Nowick 4 observed an internal friction peak in an A1-6 at. pct Ag alloy at about 140°C (0.25 cps). The peak was found to exhibit a systematic instability. After aging at successively higher temperatures between 155' and 23Z°C, the peak first migrated to higher temperatures while increasing in height, then returned to lower temperatures and decreased in height. After aging at temperatures above about 200°C, the peak position remained constant while the height decreased very slowly. In quenched specimens, elastic after-effect measurements inhcated a rapid initial transient in peak position from low temperatures up to 155°C. The authors concluded that a stress induced growth and resolution of the clusters and the 7' was the most reasonable mechanism to account for the behavior. It would seem, however, very unlikely that both the clusters and the y' precipitate would provide damping contributions whose relaxation time and activation energies were identical, which is required for them to produce the same internal friction peak. The present investigation was motivated by this apparent anomaly and the development of a very low thermal inertia torsion pendulum5 capable of monitoring transient behavior. Low frequency internal friction measurements were made on four binary A1-Ag alloys nominally containing 5, 10: 15, and 20 at. pct Ag. The results of measurements made on a 10 at. pct Ag alloy in the quenched condition are shown in Fig. 1. There are two peaks apparent in the spectrum, one centered at about 160°C, the second at about 210°C. The two peak spectrum was observed in each alloy, but it was best resolved in the 10 pct Ag specimens. Because of the instability in the internal friction, 4 it seemed possible that the second peak was not a peak at all, but simply a manifestation of a single, sharply transient, peak. This effect has been observed in Au-Ni alloys.6 The existence of the higher tempera-

Jan 1, 1970

By Glenn R. Zellars, J. P. Morris

The carrier gas method was used to measure the vapor pressure of copper over liquid copper and Fe-Cu alloys. From these results, the activity of copper in the alloys was determined at 146°, 1550°, and 1600°C. Calculations of the activity of iron were made from the results for copper. The activities of copper and iron show strong positive deviations from Raoult's law. KNOWLEDGE of vapor pressures of liquid metals has both practical and theoretical value. Fuming of metal baths is directly related to vapor pressure, and the data should bc particularly important to the technology of vacuum metallurgy. Theoretical applications include determinations of heats of vaporization, heats of solution, and activity coefficients in alloys. Methods for measuring vapor pressures of metals have been reviewed by Speiser and Spretnak.' High-vacuum procedures, such as the Langmuir and Knudsen methods, have been used most widely in recent years. However, these methods are not applicable to vapor pressures greater than lo-' mm Hg and often cannot be used in the temperature range of greatest interest. The purpose of this investigation was to develop a procedure for measuring vapor pressures of pure metals and alloys that would be applicable to pressures greater than lo-' mm Hg. The transportation or carrier gas method has been used. Copper was chosen for the initial work because its vapor pressure has been established fairly well and the reliability of the technique could be ascertained. Applicability to alloys was studied by determining the vapor pressure of copper over liquid Fe-Cu alloys. Experimental Procedure The tests were carried out in a graphite-spiral resistance furnace. The charge consisted of 50 g of metal contajned in a covered sintered-alumina crucible 1/2 in. deep and 13/8 in. ID. Two sintered-alumina tubes led from outside the furnace to within the crucible, passing through close-fitting holes in the crucible cover and radiation shield. The arrangement of the crucible and the two alumina tubes is shown in Fig. 1. The small-bore tube (1/16 in. ID by 5/16 in. OD) served as the inlet for the carrier gas. The tip of this tube touched the metal surface and the flow of gas imparted a rippling motion to the metal. In this manner the gas was brought into close contact with the metal and became saturated with metal vapor. In most of the tests the flow rate of the carrier gas was 560 ml per min, measured at room temperature. Approximately half of this saturated gas was allowed to escape from the crucible through the second alumina tube (3/16 in. ID by 5/16 in. OD) and was discharged to the atmosphere through a

Jan 1, 1957

By E. A. Gulbransen, W. S. Wysong, K. Andrew

INTRODUCTION THE reaction of carbon in solid solution in a metal with the surface oxide film on many metals may be inferred from thermodynamic calculations for high vacua and high temperature conditions. Holm1 has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. Considerable work has been described in the literature on the decarburization reaction. Several general references may be noted.2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides 0n strips of various types of chrome-nickel alloys. Some of the early experiments on the behavior of 13 pct chrome-iron in vacua of the order of 5 X 106 mm and at a temperature of 600°C have been reported.5 These experiments showed a slow reaction with the residual oxygen or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600°C pure enough to reduce Cr203 formed on the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome iron and Nichrome V has been investigated in the thin film range by Gulbransen, Phelps and Hickman,6 and shown to be Cr203. It was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pct nickel and 20 pct chromium was heated to 850°C in a high vacuum, the specimen' lost weight. The rate of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. TYPE REACTIONS Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature, of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type. They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: [I. Metal • (gas) ;--* metal + gas - degassing of the metal 2. xM(s) + y ½ 02(g) tom- M.0„ (s) – oxidation]

Jan 1, 1948

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.' Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962

By Robert T. Pring

In addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company' estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor, Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the Process. Methods of Dust Control "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are: in order .of their desirability, as follows: 1. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom prac tical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1943

By Robert T. Pring

In addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company' estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor, Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the Process. Methods of Dust Control "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are: in order .of their desirability, as follows: 1. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom prac tical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1943

By William M. Newton, John E. Sherborne

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By John E. Sherborne, William M. Newton

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By E. A. Gulbransen, W. S. Wysong, K. Andrew

The reaction of carbon in solid solution in a metal with the surface oxide fim on many metals may be inferred from thermo-dynamic calculations for high vacua and high temperature conditions. Holm has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. considerable work has been described in the literature on the de-carburization reaction. Several general references may been 2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides on strips of various types Of chrome-nickel alloys. Some of the early experiments On the behavior Of '3 pct chrome-iron in vacua of the order of 5 X lo' mm and at a temperature Of 600°C have been reported.5 These experi-merits showed a 'low reaction with the residual Oxygen Or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600' C pure enough to reduce Crz03 formed On the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome- iron and Nichrome V has been investigated in the thin film range by Gulbransenr Phelps and Hickman,' and shown to be "203. It Was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pet nicke1 and 20 pet chromium was heated to 850°C in a high vacuum, the specimen lost weight. The rate Of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. Type Reactions Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type, They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: 1. Metal . (gas) F? metal + gas — degassing of the metal 2. zM(s) + y }i Oi(g) M MIOu(s) -oxidation

Jan 1, 1949

By Kenneth L. Cook

THE five serpentine masses exposed within the northern half of Riley County, Fig. 1, constitute a major part of the few exposures of igneous rock in Kansas.' Although not many subsurface data are available for this part of Riley County,2 six deep wellsV indicate that the basement complex lies between 2500 and 3000 ft below the earth's surface. A northwestward-trending ridge in the present basement surface, which extends across the northern half of Riley County, is indicated on Mettner's contour map.' The serpentine masses lie in a region that was active during Pennsylvanian and Permian time along two main tectonic trends, which may, in part at least, have developed contemporaneously." One trend is northeasterly, as evidenced by the Nemaha anticline, the Abilene anticline, the Voshell anticline, and many other smaller northeastward-trending folds. The other trend is northwesterly, as evidenced by the central Kansas uplift, the Salina basin syncline, and smaller northwestward-trending folds. The area of the Abilene anticline was actively deformed during much of this time, and the present surface rocks, for the most part Permian in age, show many normal faults." The Bala and Leonardville intrusions lie within a mile of the axis of the Abilene anticline, Fig. 1, as mapped by Wallace Lee;' the Randolph No. 1 and Randolph No. 2 intrusions lie within about 5 miles of the axis; and the Stockdale intrusion lies within about 8 miles of the axis. The igneous rocks have intruded horizontal or gently dipping limestones and shales that are late Permian in age.V he period of intrusion, according to Moore and Landes, was probably Cretaceous.' At present a detailed description of the petrography is available for only the Bala intrusion. Moore and Haynes' describe the rock at Bala as a green, serpentinized, porphyritic, peridotite breccia containing inclusions of shale. The ground mass consists chiefly of serpentine and calcite with considerable chromite (5 to 10 pct) and some magnetite. The phenocrysts consist principally of altered olivine with some altered augite and biotite. Although probably different in petrographic details, all the serpentine masses are somewhat similar in that 1) they consist of a dark green, fine-grained ground mass of igneous rock containing many xeno-liths composed of fragments of the neighboring sedimentary rock; 2) they tend to form small mounds on the landscape, thus indicating their greater resistance to weathering and erosion; and 3) they are magnetic. Previous Magnetic Survey of the Bala Intrusion: To the writer's knowledge, only the Bala intrusion had been surveyed with a magnetometer prior to the magnetic surveys discussed in this paper. Dreyer8 interprets the intrusion as a vertical, eastward-plunging dike, on the basis of the results of his magnetic survey, Fig. 1, with a vertical magnetom-

Jan 1, 1956

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,' Dahl and Pawlek,' and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

By Craig E. Saporito

INTRODUCTION Freeport-McMoRan Inc. has been very active recently with two major discoveries and its restructuring activities. This paper describes Freeport-McMoRan's businesses, the two major mineral discoveries, and exciting opportunities within the oil and gas operations. BUSINESS ACTIVITIES Freeport-McMoRan is the largest and one of the lowest cost fully integrated U.S. phosphate fertilizer producers. It is the second largest domestic Frasch sulphur producer. Freeport- McMoRan will become the largest domestic producer of Frasch sulphur when its Main Pass Block 299 sulphur deposit reaches full production in 1993. Furthermore, it is the largest transporter of sulphur produced by others. Its oil and gas activities rank among the largest U.S. independents in terms of production and proved reserves. The copper/gold operations in Indonesia are among the world's lowest cost. When expansion operations reach full capacity levels in 1992, the Indonesian copper/gold complex will be the fifth largest copper operation in the world. Operations are divided into three business segments that include: 1. Agricultural minerals, incorporating sulphur, phosphate rock and phosphate fertilizer activities; 2. Energy, including oil and gas activities; and 3. Metals, incorporating copper, gold and silver operations in Indonesia. In early 1989, Freeport-McMoRan announced the discovery of two world-class ore bodies; a sulphur deposit off the coast of Louisiana on Main Pass Block 299, and a copper/gold deposit -- the Grasberg in Indonesia -- approximately two miles away from the existing Ertsberg East operations. As a result of these major discoveries, Freeport- McMoRan decided to carry out a restructuring program. Its purpose was to sell $1.2 to $1.5 billion of non-strategic assets. Debt levels and associated interest expenses will be significantly reduced, and general and administrative expenses will be reduced, which will place Freeport- McMoRan in an excellent position to fund the development of the Main Pass Block 299 sulphur discovery, the Grasberg discovery, and oil and gas discoveries. This restructuring program also will allow Freeport-McMoRan to achieve the greatest future value for shareholders by focusing on its principal businesses (Figure 1). Strategic Restructuring • Sell $1.2 - $1.5 Billion Of Non-Strategic Assets • Significantly Reduce Debt • Significantly Reduce G&A • Fund Development Of Main Pass & Grasberg • Stronger Company; Positioned For Future Growth • Focus Is On Principal Businesses: - Sulphur/Phosphate Fertilizers - Indonesian Copper/Gold - Oil And Natural Gas Figure 1 - Strategic Restructuring AGRICULTURAL MINERALS Main Pass Block 299 Discovery The Main Pass Block 299 discovery has a proven reserve of 67 million long tons of recoverable sulphur. This is the largest known Frasch sulphur deposit in North America. The discovery increased Freeport-McMoRan's sulphur reserves more than five-fold, and is synergistic with the company's phosphate fertilizer assets. The

Jan 1, 1990

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Zinc difhsions in gallium arsenide having surface concentrations as low as 5 x 10'' atoms per cu cm have been attained. A multiple-difhsion sequence is employed during which zinc enters the gallium arsenide from a silicon dioxide film in a solid-to-solid diffusion step. The technique is illustrated for the case of a zinc surface concentration of -1 x 1017 atoms per cu cm and a junction depth of 1.2 p. Radiotracer measurements of -0.1-p layers of gallium arsenide are used to delineate the resulting profile. A diffusion coefficient for zinc in pyrolytically deposited silicon dioxide is reported. ZINC is frequently used as an acceptor impurity in gallium arsenide. As examples, p-n junctions are formed using zinc-diffused layers in solar cells, lasers, and varactor diodes. For these purposes surface concentrations of 10'' to over loz0 zinc atoms per cu cm are desired and readily obtained from a vapor source. Diffusion of zinc into gallium arsenide to yield surface concentrations of about 1017 atoms per cu cm, however, is more difficult. For instance, oldstein' reports that large changes in the vapor density of zinc produce only small changes in surface concentration. Such low surface concentrations are necessary in forming the diffused base of a gallium arsenide double-diffused n-p-n transistor in order to obtain an adequate emitter efficiency. An alternative approach to zinc diffusion which can provide reduction in surface concentration of several orders of magnitude is the introduction of the diffusant from a solid source. This can be conveniently accomplished by using oxide films of the type generally employed for selective diffusion masking. Such oxides also serve to prevent the dissociation of the gallium arsenide surface at the high temperatures of diffusion. DIFFUSION PROCEDURE Fig. 1 illustrates the diffusion sequence which is employed for obtaining zinc surface concentrations in the range from 5 x lom to 1 X 10" atoms per cu cm. The description of technique will be given for the instance of -1 x 1017, which is typically utilized in double-diffused gallium arsenide transistor investigations at this laboratory. Tin- or germanium-doped gallium arsenide wafers drawn from crystals grown by horizontal Bridgman or Czochralski techniques are used, with bulk concentrations ranging from 1 to 3 X 10" carrier atoms per cu cm. Each wafer is chemically polished on the (iii) arsenic face using a mixture of five parts concentrated sul-furic acid, one part water, and one part 30 pct hydrogen peroxide at room temperature, followed by rinsing in deionized and quartz-distilled water. Pyrolytic silicon dioxide was chosen as the oxide coating because of the high quality of the films obtainable, the ease of their preparation, and the excellent control over film thickness and uniformity.

Jan 1, 1964

The Molycorp operation at Mountain Pass, California, is unique in that it is the only place in the world where bastnasite is mined. The orebody is a metamorphic carbonatite; the mineral of importance is bastnasite, a fluocarbonate containing principally cerium, lanthanum, neodymium, and praseodymium, with small amounts of samarium, gadolinium, and europium. In addition, appreciable quantities of barite, calcite, and strontianite are present. Molycorp had mined and processed the bastnasite ore since the early 1950s at a rate of about 100 tpd by a unique hot flotation process in a plant originally used for cyanidation of gold ore. The concentrate was primarily used in high quality glass polishing, lighter flints, ceramics, and in specialty steel making. Then in the early 1960s, Molycorp and the Colorado School of Mines Research Foundation developed a solvent extraction process to recover europium from the bulk rare earth concentrates. In 1965 a new SX plant was constructed to produce this material for use as a red phosphor in color television tubes. Because of the demand for this material, a new 500 tpd concentrator was designed and constructed in 9 ½ months. Then, because of a sharply increased demand for europium, the plant was expanded to 1200 tpd only four months after completion of the original construction. The crushing section of the new plant was designed similarly to those portable units used in road construction and arrived on the site in ten major pieces. Foundations were concrete piers; and after their completion, the entire crushing plant composed of primary and secondary crushers, conveyors, and a screen was erected in fourteen days by a crew of ten men assisted by a mobile crane. Pit-run ore is loaded into 35-ton trucks by a 7 yd (5.4 cu m) loader, trans- ported to .the crushing plant, and dumped into the 65 -ton concrete pocket. A 42 in. by 20 ft (1.07 m by 6. 1 m) apron feeder feeds ore to the 30 in. by 42 in. (760 rnrn by 1070 mm) single toggle jaw crusher. Crushed ore is trans- ferred by a scissors conveyor to a 5 ft by 14 ft (1.52 m by 4. 27 m) double- deck screen which produces a final ¾ in. (19 rnrn) product with the oversize being treated in a 4 ¼ ft (1. 3 m) standard cone crusher. Cone crusher product is returned to the first scissors conveyor to join the primary crusher product. Dust collection is by a wet scrubber, and an operator's control room is located to overlook the primary. The entire crushing is in the open, and a 30-ton mobile crane is used for maintenance. Molycorp’s two-stage crushing plant is an excellent example of functional design for a small mining and milling operation.

Jan 1, 1978

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953