Search Documents

By G. H. Wigton

THE oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods. are unsatisfactory, as the lead smelters heavily penalize the large amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under; the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this interval, an experimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments were resumed. The highly infusible flotation. tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent. common salt showed -nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus,

Jan 8, 1925

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By H. E. Elliott, R. S. Busk, A. T. Peters

One of the problems of the fabricator of metals and alloys is the propensity of some composition rarnges toward abnoermal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, 9 per cent A1, 2 Per cent Zn, 0.2 Per cent Mn) and G alloy (Mg, 10 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other meta1s- Jeffries and Archer1 have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. Before recent developments, this phenomenon of abnormal local grain growth Was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. I) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The DOW Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germinasium since this term has been definedl as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By H. A. Domian, H. Biloni, G. F. Bolling

Jan 1, 1965

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By W. A. Krivsky, R. Schuhmann

Jan 1, 1962

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

By J. C. Martin

Equations for three-phase, three-dimensional, compressible flow (including capillarity) are reduced to two-dimensional relations by a partial integration. This reduction allows three-dimensional flow problems to be treated with mathematics for only two spatial dimensions. The results can be used to formulate flow equations for two-dimensional reservoir simulators in which the effects of capillarity and fluid segregation in the third dimension are represented. Such reservoir simulators would retain many of the aduantages of two-dimensional simulators while simulating three-dimensional effects. The principal restriction of the method is that the thickness of the reservoir should be small, compared to the distance across the reservoir. INTRODUCTION In recent years, computers have been used to calculate the performances of many reservoirs. Most of the detailed calculations, however, are based on finite difference solutions of the flow equations, and present day computers are seldom able to handle a sufficient number of cells to produce entirely satisfactory solutions, even for reservoirs represented by two-dimensional arrays of cells. The situation becomes much worse when one wishes to approximate the reservoir by a three-dimensional array. A great saving in computation or a more detailed solution can be obtained for many reservoirs by using the partial integration of the equations of flow presented in this paper. The integration reduces the three-dimensional equations to two-dimensional relations; and, for studies of two-dimensional flows in vertical cross-sections, the equations are reduced to one-dimensional relations. Most reservoir performance calculations currently are based on one- or two-dimensional flow re1ations.l-3 In some cases flow in the third dimension is approximated by assuming a particular type of vertical saturation distribution, such as gravity segregation.l.2. The relations developed in this paper approach those for segregated flow as the capillary pressures approach zero, and they approach those for uniformly distributed saturations as the capillary pressures are increased. For this analysis, the ratio of the reservoir's thickness to the maximum distance across it must be small. The capillary pressures between the oil and water should also be small compared to the maximum pressure difference in the reservoir. This requirement is met by most reservoirs. It is assumed that the capillary-pressure curves are well defined, whether or not hysteresis effects are included. Also, the reservoir must have sufficient vertical permeability to allow the fluids to segregate. The results presented here provide a firm theoretical foundation to Coats' et aL5 assumption of vertical equilibrium and extend the relations to three-phase flow. Coats' assumption of vertical equilibrium, which he verified by calculations and experiment, is developed here mathematically from basic flow equations. DISCUSSION SATURATION AND PRESSURE DISTRIBUTIONS Appendix A presents a mathematical analysis of fluid flow in reservoirs where the ratio of thickness to maximum distance across the reservoir is small. The results indicate: (1) that the fluids along any line perpendicular to such a reservoir's upper surface are in static capillary equilibrium (vertical equilibrium); (2) that, to a first approximation, the fluid pressures and properties are functions of only areal position in the reservoir and time; and (3) that hydrostatic pressure gradients exist along any line perpendicular to the reservoir's upper surface. The results might be expected after studying several physical considerations. First, no flow is allowed normal to the upper and lower reservoir boundaries, which are relatively close together.

Jan 1, 1969

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth's crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth's surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b'/a,+Qc/a' [2]

Jan 1, 1963

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966