Search Documents

By Theron Wasson

The state of Michigan showed considerable activity during 1935. The center of greatest interest was the Crystal field, which was unknown until March, 1935, and is an illustration of the effect of the unknown and unexpected on Michigan oil development. The fields of the state (Fig. 1) produced a total of 15,770,000 bbl. of oil in 1935, or about 5 million more than in 1934. In order to keep up this production 307 new oil wells were drilled, of which 88 were in the Crystal area, which produced 3,600,000 bbl. This field had a rapid development and reached its peak in October. Since that time increasing water encroachment has caused a rapid decline. The pay horizon at the top of the Monroe dolomite is only a few feet thick. Big producers were offset by dry holes or small wells. The discovery well, which was in section 11, Crystal township, Montcalm County, was drilled March 28, 1935. Its initial production was 5000 bbl. per day, and up to Dec. 31, 1935, had produced 350,000 bbl. of oil—dose to one-tenth of the total production of the field to that date. The Beaverton field, which was discovered at the close of 1934, did not develop rapidly. Four small producers were finished in the Dundee lime during the year. West Branch was active and at the end of the year had 97 producers, 72 of which were drilled during 1935. Most of the wells produce from the Dundee lime; a few are finished in the Traverse. The Birch Run field deserves special mention, for it is the one area where consistent production continues to be found in the Berea sand at about 1500 ft. Wells are small, 20 now producing a total of about 300 bbl. per day of oil of fine quality. The old Central Michigan producing area, extending from Nit,. Pleasant through Yost to Porter, continued to be the principal producing area of the state and accounted for 10,370,000 bbl. from 660 producing wells. Ninety-three new wells were drilled in this territory. The Porter field, at the southeast end of this producing trend, was outstanding from the standpoint of production. The old Leaton field of Isabella County added several new producers. Its production was greater than in 1934.

Jan 1, 1936

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By Theron Wasson

The state of Michigan showed considerable activity during 1935. The center of greatest interest was the Crystal field, which was unknown until March, 1935, and is an illustration of the effect of the unknown and unexpected on Michigan oil development. The fields of the state (Fig. 1) produced a total of 15,770,000 bbl. of oil in 1935, or about 5 million more than in 1934. In order to keep up this production 307 new oil wells were drilled, of which 88 were in the Crystal area, which produced 3,600,000 bbl. This field had a rapid development and reached its peak in October. Since that time increasing water encroachment has caused a rapid decline. The pay horizon at the top of the Monroe dolomite is only a few feet thick. Big producers were offset by dry holes or small wells. The discovery well, which was in section 11, Crystal township, Montcalm County, was drilled March 28, 1935. Its initial production was 5000 bbl. per day, and up to Dec. 31, 1935, had produced 350,000 bbl. of oil—dose to one-tenth of the total production of the field to that date. The Beaverton field, which was discovered at the close of 1934, did not develop rapidly. Four small producers were finished in the Dundee lime during the year. West Branch was active and at the end of the year had 97 producers, 72 of which were drilled during 1935. Most of the wells produce from the Dundee lime; a few are finished in the Traverse. The Birch Run field deserves special mention, for it is the one area where consistent production continues to be found in the Berea sand at about 1500 ft. Wells are small, 20 now producing a total of about 300 bbl. per day of oil of fine quality. The old Central Michigan producing area, extending from Nit,. Pleasant through Yost to Porter, continued to be the principal producing area of the state and accounted for 10,370,000 bbl. from 660 producing wells. Ninety-three new wells were drilled in this territory. The Porter field, at the southeast end of this producing trend, was outstanding from the standpoint of production. The old Leaton field of Isabella County added several new producers. Its production was greater than in 1934.

Jan 1, 1936

By S. H. Davis

The pyrites used in making sulfuric acid in the United States have been largely imported from Spain and Canada, the Spanish imports amounting to nearly 1,000,000 tons per annum in the pre-war period. The greatly increased use of sulfuric acid and the cutting off of these Spanish imports, incident to war conditions, brought about a threatened shortage of sulfur supplies during the war period. The bituminous-coal mines of ccrtain districts have, for many years, furnished a small tonnage of pyrite in the form of coal brasses. A mechanical concentrator at Danville, Ill., for a number of years, has been treating hand-picked lump pyrite and coal from the picking belt and from the mines and a small plant near Gillespie, Ill., for a few months has been recovering pyrite from washery refuse. Many mines throughout Illinois, Indiana, Western Kentucky, Ohio, and Pennsylvania have shipped an occasional car of the hand-cleaned lump pyrite. Only a very small percentage of the available pyrite has been recovered in this way, however, as usually the miners throw such lumps into the gob with slate and other impurities. It has been estimated that the western Indiana coal field could furnish more than 100,000 tons of pyrite per annum. The present production is very small. The possibility of furnishing the domestic trade with pyrites recovered as a byproduct from coal-mining operations appears attractive but there are certain features difficult to overcome. Pyrite, to be used in acid making, must meet with certain requirements as to size and purity. Lump ore for grate burners should be under 3 in. (7.6 cm.) and over 1 in. (2.5 cm.) in diameter. Fines for use in mechanical roasters should be under quarter mesh. The material should be high in sulfur, free from arsenic and phosphorus, and as low in carbon as possible. The pyrite obtained from coal can be made to meet all the above requirements, but it is difficult to remove all the carbon. The pyrite in coal occurs as bands and nodules of varying thickness and size and of comparative purity, but mixed with this is more or less web sulfur. The web sulfur carries admixed coal, which may make the concentrate run up to several per cent. carbon. This makes the concentrates subject to firing, causes heavy consumption of niter, and lowers the acid-plant capacity, due to dilution of gases. The hand-cleaning methods

Jan 1, 1920

By W. A. Binsacca

The concentrator treats sulfide ore containing lead, copper, zinc, gold and silver, at the rate of 850 tons per 24 hr., and produces lead, copper, zinc and iron concentrates by selective flotation methods. The ore occurs below the oxidized zone along a main fracture, the wall rock of which is either greywacke or calcareous shale. The predominating sulfide minerals are galena, sphalerite, pyrite and chalcopyrite; the others are quartz and calcite. In minor amounts, arsenopyrite, pyrrhotite and hematite occur, and such secondary minerals as smithsonite, chalcocite, covellite, bornite, cerussite and anglesite are detected in the ore, the last two named occurring principally as surface alterations of the galena. The ore is hauled from the mine bins in 10-ton cars which pass over the track scales before entering the car dumper ahead of the crusher plant.' A conveyor belt delivers the crushed ore to the sulfide bin, which has a capacity of 2800 tons. The primary grinding unit consists of two 6 by 12-ft. Marcy rod mills operating in parallel and in open circuit, each taking 425 tons per day. One rod mill discharges into an 8 by 25-ft. Dorr classifier with a 12-ft. bowl and the other into a 6 by 25-ft. Dorr duplex classifier. These classifiers are arranged so that each unit rakes the sands into a 6 by 14-ft. Traylor ball mill, which discharges to the bowl classifier only. The duplex classifier therefore operates in open circuit and the bowl classifier in closed circuit, the overflow of both classifiers furnishing the feed for the flotation section. Other groupings have been tried, but this has been found the most satisfactory. The Marcy mills are driven by 150-hp. slip-ring induction motors with speed reducers to give 17 r.p.m. The Traylor mill operates at a speed of 24 r.p.m. and is driven by a 200-hp. slip-ring induction motor, direct connected to pinion and gear. The bowl classifier operates at a speed of 22 r.p.m., with the bowl rake making 4.5 r.p.m. and the duplex classifier at 31 r.p.m. High-carbon steel rods of Mexican manufacture, 12 ft. long by 3-in. diameter, are used in the Marcy mills, with a resulting consumption of 1.52 Ib. per ton ore. The Traylor mill is fed 3-in. cast-iron balls cast in

Jan 1, 1935

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.' More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By Warren L. Howes

LITERALLY hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be clues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations,1 grinding capacity usually is the greater consideration. GRINDING CAPACITY Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. [ ] From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell liners

Jan 1, 1945

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

WILLIAM H. KOBBÉ (communication to the Secretary*).-I have read with much interest the discussion of my paper by Arthur Knapp and I. N. Knapp published in the March Bulletin. These discussions apparently assume that my paper advances a. number of ideas that are not intended: 1. That the total sandbody or pay is to be removed. 2. That upon bringing this sand and oil to the surface 100 per cent., or perfect separation, can take place. 3. That this tremendous quantity of sand is then hauled away in wagons and distributed as road material. The paper raider discussion is not a theoretical treatment of the subject but is the result of actual experience in oil production under the conditions mentioned.. That wells that produce sand produce in ore oil, and the best operating methods to bring this about are fully treated. It is, of course, impossible to remove all the oil sand underlying a property, but the greater the amount removed the greater becomes the production of oil. As stated in my paper, the surface disposal of this large volume of sand is a problem and the only use to which it can be put is road surfacing; but I did not intend to convey the idea that all this sand was thus used. Only a very small quantity was required on the company's roads, and two wagons only were employed for this purpose. The remaining sand accumulated in the numerous "washes" and sumps. Although this sand contained sufficient oil to stain the hands, it was, surprisingly dry and could be easily shoveled. As stated in the paper, "the piles of sand are gradually freed of their oil content and a crust forms on their surface which will bear the weight of a man." I consider this a high degree of separation. A small amount of oil necessarily remains in the sand and is held there by capillarity. Otherwise it would be useless as a road binder, and, furthermore, to recover such oil special processes of treating are required. Arthur Knapp says, "of the total volume produced by pumping, not more than 4 or 5 per cent. can possibly be sand." I cannot agree with this statement as I have managed many properties where the wells were so operated that the amount of sand produced was five times this figure.

Jan 6, 1917

By George H. Ashley

At the beginning of the war, about 13 years ago, a conference was called in Washington to lay plans for pooling the coals of the United States. A careful review of the various systems of classification then extant showed none well adapted to the needs of coal pooling. The system of Tidewater pools then adopted, using numbers to distinguish one pool from another, was based on typical coals of different localities. At that time, the writer undertook the preparation of such a practical classification. Aside from drawing on his experience of over 20 years in the coal fields of the United States, reaching from the Pacific Coast and the Rio Grande to Rhode Island, he first examined and carded all of the large collection of coals in glass jars made by and for M. R. Campbell. Next, he carded all of the descriptions of coals he could find in the U. S. Geological Survey bulletins and elsewhere, as well as practical tests of coals by the Navy and other organizations and then took account of every published coal analysis of the U. S. Geological Survey and U. S. Bureau of Mines. A study of this information, involving thousands of recomputations, led to the presentation of a paper on "A Use Classification of Coal" before this Institute at the Chicago meeting, September, 1919. That classification was unique (1) in a classification based on "standard coal" which included moisture, but used standardized ash, sulfur and nitrogen, (2) in using physical properties to distinguish the major classes or orders, (3) in recognizing British thermal unit values in the minor subdivision, (4) in the large number of classes recognized (thirty-six), (5) in proposing mineral names for all classes, (6) in proposing a letter code for the several classes for practical use, (7) in proposing a code for expressing what has commonly been called "grade" of the coal, the grade code to be combined with the rank code to designate and describe a coal. The writer still thinks that the principles then offered, though not necessarily the exact proposals, are valid and desirable in any practical classification. The actual classification of coal by rank was based on the ratio of fixed carbon to volatile matter for the high-rank coals—the well-known

Jan 1, 1930

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

By Wallace Ralston

The East Texas district includes the northeast 38 counties of the State of Texas. It still remains one of the most important oil-and-gas-producing areas of the United States, since it includes within its boundaries the large East Texas field. Other fields of importance are: Van, Rodessa, Talco, Cayuga, Long Lake and Sulphur Bluff. Production is from the Nacatoch, Blossom, and Woodbine of the upper Cretaceous and the Paluxy and Glen Rose of the lower Cretaceous. Of these, the Woodbine is the most important, since it is the producing horizon iri the East Texas field. Fields East Texas Field.—There were 2471 oil wells, 1 gas well and 84 failures completed during the year of 1936 in the East Texas field; that is, 1565 fewer than in the year of 1935. The total number of producing wells is now 22,031, of which 50 are temporarily shut down; 18,435 wells flowing their production; 3150 pumping; 293 on gas-lift, and 82 operated by other methods. This shows an increase of 1642 wells on artificial lift over Jan. 1, 1935. The average daily salt-water production is estimated at 42,700 bbl. from 2327 wells—an increase of 1201 wells over the year of 1935. The field is now drilled to an average density of one well to 5.85 acres. Average bottom-hole pressure has dropped from 1193 Ib. to 1168 lb., approximately 1 lb. drop for each 6,600,000 bbl. of oil produced. During the month of December 1936, the estimated daily average production of illegal oil had dropped from 20,500 bbl. in December 1935 to 7500 bbl. The commercial gas production is of minor importance in the East Texas field, and figures for the amount of gas taken from the field are not available at the present time. Talco Field, Titus and Franklin Counties.—The discovery well was drilled by Housh, Thompson et al. on the C. M. Carr tract and completed in March 1936, as a pumping well making 552 bbl. per day of 24' gravity oil. This well was first completed at a total depth of 4208 ft., the top of the sand being 4190 ft. Later it was deepened to 4260 ft., which increased the production from 552 to 725 bbl. per day. This field is producing

Jan 1, 1937

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-' It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969

By H. G. Botset

A KNOWLEDGE of the water content of producing sands is becoming of increasing importance to the petroleum industry. It is now a generally accepted fact that practically all oil sands contain some free water. Recent experiments1 have shown that an appreciable fraction of the pore space of a sand may be filled with water while oil production from this sand is water-free. Crowther and Haines,2 in experiments on electro-endosmosis in soils, reported that there was no endosmotic flow of water when the moisture content of the soil was 14 per cent or less, indicating that the moisture content of the soil below 14 per cent was held by dif-ferent forces than the water content above this value. This result is confirmed qualitatively by Dunlap,1 who found that "as the volume of water in the voids exceeds approximately 15 per cent of the pore volume, the permeability of the core to kerosene is markedly reduced." The author3 has also found in other experiments that the gas flow through a water-saturated sand reaches essentially 100 per cent when the pores of the sand still contain from 10 to 15 per cent water. The velocities of the flowing fluid in the experiments cited were comparatively high, so that in practice one may expect, at lower fluid velocities, an even higher moisture content of the sands with water-free oil or gas production. Thus a knowledge of the water content of oil-field sands becomes of con-siderable importance in estimating petroleum and gas reserves, and effi-ciency of fluid recoveries from depleted reservoirs. Rapid and reasonably accurate methods of measuring the water content of sand cores have not been described so far in any literature that has come to our attention.4 The method described below is devel-oped from methods that have been used for some time to measure the water content of alcohols.5,6,7 It is an application of the fact that in the presence of certain organic liquids such as kerosene, carbon tetrachloride, xylol, etc., water and alcohol are only partly miscible. This relation-ship has been used for some time in the study of gasoline-alcohol mixtures where the presence of small quantities of water affect the solubility of

Jan 1, 1938

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949

By Lewis A. Riley

I desire to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomerates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideratiotl in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

By John J. Egan

THE present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire Submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all Substances that occur or that may be in any way associated with steelmaking operations, Such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. SPECIFIC HEATS, HEATS OF FORMATION, ENTROPIES AND FREE ENERGIES OF VARIOUS PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES. I . Determination of specific heats and entropies of oxides, sulphides, nitrides, etc. over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc. over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineralogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the length of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel per day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel per day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from the commonly understood barrel per day value, in that the conditions surrounding the sale of one lease or property at a fair market value may

Jan 1, 1922

By D. Mizer, J. B. Clark

In a recent investigation of the entire magnesium-yttrium phase diagram, Gibson and Carlsonl report the maximum solid solubility of yttrium in magnesium as 8.0 wt pct Y at 1050°F (565°C). However, independent studies of the precipitation in magnesium-yttrium alloys, 2 conducted prior to the publication of the above phase diagram, indicated a greater solid solubility of yttrium in magnesium. Accordingly, the magnesium-rich region of the diagram was re-investigated to determine more accurately the liqui-dus, solidus, and solvus of the magnesium solid solution in this system. Metallography and thermal analysis were chosen as the best corroboratory methods for accurately determining this region of the diagram. A magnesium-yttrium master alloy was prepared from yttrium of 99.9 pct purity and singly sublimed magnesium of 99.9 pct purity. Subsequently, the twelve magnesium-yttrium alloys shown in Fig. 1 were prepared using standard alloying procedures for magnesium. Metallographic samples of the alloys were heat treated under an SO, atmosphere in an electric furnace capable of control within ±3oF of the desired temperature. Alloy samples for the metallographic determination of the solvus, and for the precipitation studies were solution treated at 1000° F for 16 hr. Subsequent aging times for the solvus determination varied from a minimum of 6 hr for the higher temperatures up to 816 hr for lower temperatures. Periods of 30 min at temperature were used to generate liquation for the metallographic placement of the solidus and eutectic horizontal. The liquidus and the eutectic horizontal were determined by thermal analysis. Simple time-temper- ature heating and cooling curves were obtained from 10-g alloy samples heated and cooled in a well-insulated electric furnace. An Iron-Constantan thermocouple was placed in direct contact with the sample. The thermocouple did not contaminate the alloy sample since metallographic examination showed that the alloy melt did not wet or attack the thermocouple. The heating and cooling rates were approximately 5 to 8OF per min. The standard metallographic procedures for magnesium were used in polishing and etching the magnesium-yttrium alloys studied. Glycol etchant* was etchant was used to reveal precipitate in the solvus determination. The redetermined magnesium-rich region of the magnesium-yttrium diagram is shown in Fig. 1. The

Jan 1, 1962