Search Documents

By M. K. Geer, H. F. Yancey

Investigations of the fundamental factors involved in the performance of various coal-cleaning processes have constituted a substantial portion of the research 011 coal cleaning conducted by the Bureau of Mines. These detailed studies of the mechanism of separating coal from impurity in various cleaning devices were undertaken to provide the coal industry with information that is helpful in selecting the type of cleaner most suitable for treating a particular coal. Previous reports describing these investigations have dealt with the wet table,1 the pneumatic table,' and the plunger,3 pulsator.4 and Baum types5 of jigs. The present report compares the performance of three commonly used units treating the same coal—a pneumatic jig, also known as the air-flow. cleaner, a pneumatic table, and a Baum-type jig. Object and Plan The fact that pneumatic coal-cleaning processes are less efficient than wet-washing methods because they are unable to make as sharp a separation between coal and impurity is well recogilized. The literature, however, contains little quantitative in- formation on the relative performances of the two types of cleaners. The object of the present report is to present a detailed comparison of the performances of two pneumatic units and one wet-washing process treating coal from the same bed. Although the information in this report demonstrates that the performance of the pneumatic cleaners is not as good as that of those employing water, it must not be construed as reflecting on the usefullless of such equipment. Performance is often secondary to other factors in the selection of coal-cleaning equipment, and the advantages inherent in pneumatic processes frequently outweigh the limitations imposed by their performance. Specific gravity and particle size are the principal factors that influence the separation of coal from impurity in either pneumatic or wet processes; consequently, the tools available for this investigation were the float-and-sink bath and the screen. Accordingly, the raw coal, clean coal, and refuse samples representing the operation of each type of cleaning unit were first separated into a series of density fractions by means of the float-and-sink bath, and then each density fraction was screened into a series of size fractions. By this procedure the raw coal, clean coal, and refuse were subdivided into components of restricted ranges in density and size. From these data it was possible to determine how the cleaning unit disposed of each component of the raw coal; that is. what proportion of each component is sent to clean coal or rejected as refuse.

Jan 1, 1947

By H. F. Yancey, M. K. Geer

Investigations of the fundamental factors involved in the performance of various coal-cleaning processes have constituted a substantial portion of the research 011 coal cleaning conducted by the Bureau of Mines. These detailed studies of the mechanism of separating coal from impurity in various cleaning devices were undertaken to provide the coal industry with information that is helpful in selecting the type of cleaner most suitable for treating a particular coal. Previous reports describing these investigations have dealt with the wet table,1 the pneumatic table,' and the plunger,3 pulsator.4 and Baum types5 of jigs. The present report compares the performance of three commonly used units treating the same coal—a pneumatic jig, also known as the air-flow. cleaner, a pneumatic table, and a Baum-type jig. Object and Plan The fact that pneumatic coal-cleaning processes are less efficient than wet-washing methods because they are unable to make as sharp a separation between coal and impurity is well recogilized. The literature, however, contains little quantitative in- formation on the relative performances of the two types of cleaners. The object of the present report is to present a detailed comparison of the performances of two pneumatic units and one wet-washing process treating coal from the same bed. Although the information in this report demonstrates that the performance of the pneumatic cleaners is not as good as that of those employing water, it must not be construed as reflecting on the usefullless of such equipment. Performance is often secondary to other factors in the selection of coal-cleaning equipment, and the advantages inherent in pneumatic processes frequently outweigh the limitations imposed by their performance. Specific gravity and particle size are the principal factors that influence the separation of coal from impurity in either pneumatic or wet processes; consequently, the tools available for this investigation were the float-and-sink bath and the screen. Accordingly, the raw coal, clean coal, and refuse samples representing the operation of each type of cleaning unit were first separated into a series of density fractions by means of the float-and-sink bath, and then each density fraction was screened into a series of size fractions. By this procedure the raw coal, clean coal, and refuse were subdivided into components of restricted ranges in density and size. From these data it was possible to determine how the cleaning unit disposed of each component of the raw coal; that is. what proportion of each component is sent to clean coal or rejected as refuse.

Jan 1, 1947

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By John Brown

As a part of a symposium on the relations of structure to ore deposi-tion, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replace-ment deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifica-tions, to mineralization in unmetamorphosed limestone. In metamorphosed forma-tions, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a lime-stone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone-is of little or no importance.

Jan 1, 1940

By Edwin Hopkins

THE year 1923 started a few days after the Venezuelan Oil Concessions, Ltd., discovered a 140,000-bbl. well at. La Rosa and a well of between 2500 and 5000 bbl. at La Paz, on the opposite side of Lake Maracaibo. These nearly simultaneous events changed, overnight, the general aspect of oil affairs in Venezuela. Up to that time, big things had been expected by the companies then in the district, but many major companies had shown little interest in the country. Within a few weeks the Pure Oil. Co. and the Gulf Oil Corpn. entered the field and acquired large properties. The Texas Co. purchased several concessions and the Standard of California, Atlantic Refining Co., and Mexican Petroleum Co. established offices. Representatives of many other companies visited the district during the first few months of the year. The sudden influx of buyers naturally caused a great rise in prices and this, together with overproduction in the United States, doubtless caused the slowing up of concession transfers in the latter part of the year. The following property transfers occurred: (1) The Gulf Oil Corpn. contract with the Maracaibo Oil Exploration Corpn., whereby the Gulf acquired the right to select 100,000 acres from the Maracaibo's zones. (2) The Gulf Co. purchase of one-quarter interest in seven concessions of the New England Oil Corpn., Ltd. (3) The Gulf Oil Corpn. purchase of several concessions of Kunhardt and others in the Perija district. (4) The Gulf Oil Corpn. purchase of certain portions of the one-kilometer Lake zone that were not covered by parcels or Government reserves (namely the "sobrantes"). (5) Pure Oil Co. purchase of all Government reserves turned back by Maracaibo Oil Exploration Corpn. in the districts of Mara and Miranda. (6) Standard Oil Co.: of New Jersey deal with the British Controlled Oilfields, Ltd., for control of approxi-mately the eastern third of the .district of Buchivacoa, state of Falcon. (7) Royal Dutch deal with the British Controlled Oilfields, Ltd., for the control of the central third of the district of Buchivacoa, Falcon. (8) The Texas Co. purchase of several concessions in Perija and one west of Mene Grande on the east side of Lake Maracaibo. (9) Purchase by the British Equatorial Oil Co., Ltd., of Goverment reserves corresponding to certain Creole Syndicate parcels under the margin of Lake Maracaibo near La Paz. (10) The Lago Petroleum Co. acquired a concession on all of Lake Maracaibo except a 1-Km. strip along the shore.

Jan 3, 1924

By Frederick Laist

0. C. RALSTON, Salt Lake City, Utah.-I have merely glanced over this paper, consequently, I am hardly in a position to discuss it intelligently. There is one thing, however, that is of interest, that is, the claim that the oil mixture which they have chosen is the best adapted to the work at hand. I would like to ask Mr. Mathewson if they still feel that that is the case-if that really does give the best grade of concentration and the best extraction for the same money, compared to any particular oil mixture which they could get. E. P. MATHEWSON, Anaconda, Mont.-We are still using that mixture, and we consider it the most economical mixture used. DAVID COLE, El Paso, Texas.-I would like to ask Mr. Ralston if there are some other mixtures that would be better? E. P. MATHEWSON.-We are open to suggestions. 0. C. RALSTON.-My own paper on oils* calls attention to the fact that certain hardwood oils, especially the tars, are now being burned or wasted. A great deal of hardwood tar is available as low as 4 or 5 c. per gallon, that being its value as fuel under the boilers. As a matter of fact, a great deal of testing has been done with only the commercial products that are as a usual ride sold on the market. Very little hardwood tar is sold on the market. In asking a great many people who have tested flotation oils, I have not heard hardwood tar mentioned very often. I think I would add to that that the hardwood tars can probably be bought in quantity comparable with the sludge acid at Anaconda, and. should contain a greater proportion of the frothing constituent, and at a price fairly commensurate with what they pay for the sludge acid. E. P. MATHEWSON.-I would like to make a correction in one statement I made that there has been no change made in the mixture. This change has been made: We found that the amount of wood creosote in treating the sand from tables was extremely small, and we tried some experiments on a large scale, dropping it out and using simply the sludge acid and sulphuric acid. We found that this gave practically as good results as wood creosote. We use wood creosote in treating the slimes. We find it necessary in that operation. DAVID COLE.-I would like to ask, what is sludge acid?

Jan 10, 1916

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objection- able to the buyer. It is still extensively practiced on the plus 1-in. sizes, and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for efficient hand picking. At most mines an attempt is made to remove the visual impurities at one or more of the following places in the surface plant:2 (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors;. (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each-piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not 'exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and-rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft, in width, so that a picker on either side will be able to remove impurities from the center of

Jan 1, 1943

By Charles R. L. Oder, Howard W. Miller

Approximately 5000 tons of zinc ore a day was mined during 1943 in the Mascot-Jefferson City district in East Tennessee. This ore came from the Kingsport formation, a part of the Knox dolomite, of Ordovician age. The Kings-port is composed of 350 to 400 ft. of limestone and dolomite. Thin cherts, sandy layers and shales are numerous. Frequently, the limestones are altered to crystalline dolomite. The Kingsport is divisible into four main lithologic zones. These divisions are illustrated in an accompanying table, which gives detailed sections of the ore-bearing beds as found in the mines and shows the exact positions of the various ore zones within the formation. Key beds are described and the practical applications of stratigraphy in mapping, prospecting and mining are discussed. Introduction The Mascot-Jefferson City zinc district is in Knox and Jefferson Counties, in the Great Valley of East Tennessee. It extends from Mascot, I3 miles northeast of Knoxville, to Jefferson City, about 30 miles northeast of that city. The American Zinc Company of Tennessee is producing from five mines in the district, in which it has operated for more than 30 years. The only other important producer is the Universal Exploration Co. The approximate daily production of the district in 1943 was 5000 tons of sulphide ore, grading from 2.5 to 6 per cent zinc. Small amounts of oxidized ore are mined intermittently. The Knox dolomite has been described by various geologists,'-' but no detailed descriptions of the rock sections revealed by mining have been published. Rock units are not conspicuously different and careful study is required to distinguish them. Nevertheless, familiarity with the stratigraphy of the mineralized zones is essential to successful exploration and extraction of the ores; therefore the purpose of this paper is to give detailed stratigraphic sections as measured in the mines, to discuss their important features and to show their relationship to the stratigraphy of the district. Generalized Section Table I gives the most characteristic general features of the major stratigraphic units. The formation names given in parenthesis are locally and widely used terms, the correlations of which are not necessarily established. For this reason they are put in quotation marks and are replaced by more restricted terms. The names "Mascot" and "Kingsport" were adopted from local towns. They were chosen jointly by Josiah Bridge, of the Federal Geological Survey, and the senior author for use in their separate unpublished manuscripts describing the Knox dolomite in East Tennessee. Descriptions of the type sections may soon be published. The name "Longview" was first applied by Butts6 in Alabama.

Jan 1, 1949

By Howard W. Miller, Charles R. L. Oder

Approximately 5000 tons of zinc ore a day was mined during 1943 in the Mascot-Jefferson City district in East Tennessee. This ore came from the Kingsport formation, a part of the Knox dolomite, of Ordovician age. The Kings-port is composed of 350 to 400 ft. of limestone and dolomite. Thin cherts, sandy layers and shales are numerous. Frequently, the limestones are altered to crystalline dolomite. The Kingsport is divisible into four main lithologic zones. These divisions are illustrated in an accompanying table, which gives detailed sections of the ore-bearing beds as found in the mines and shows the exact positions of the various ore zones within the formation. Key beds are described and the practical applications of stratigraphy in mapping, prospecting and mining are discussed. Introduction The Mascot-Jefferson City zinc district is in Knox and Jefferson Counties, in the Great Valley of East Tennessee. It extends from Mascot, I3 miles northeast of Knoxville, to Jefferson City, about 30 miles northeast of that city. The American Zinc Company of Tennessee is producing from five mines in the district, in which it has operated for more than 30 years. The only other important producer is the Universal Exploration Co. The approximate daily production of the district in 1943 was 5000 tons of sulphide ore, grading from 2.5 to 6 per cent zinc. Small amounts of oxidized ore are mined intermittently. The Knox dolomite has been described by various geologists,'-' but no detailed descriptions of the rock sections revealed by mining have been published. Rock units are not conspicuously different and careful study is required to distinguish them. Nevertheless, familiarity with the stratigraphy of the mineralized zones is essential to successful exploration and extraction of the ores; therefore the purpose of this paper is to give detailed stratigraphic sections as measured in the mines, to discuss their important features and to show their relationship to the stratigraphy of the district. Generalized Section Table I gives the most characteristic general features of the major stratigraphic units. The formation names given in parenthesis are locally and widely used terms, the correlations of which are not necessarily established. For this reason they are put in quotation marks and are replaced by more restricted terms. The names "Mascot" and "Kingsport" were adopted from local towns. They were chosen jointly by Josiah Bridge, of the Federal Geological Survey, and the senior author for use in their separate unpublished manuscripts describing the Knox dolomite in East Tennessee. Descriptions of the type sections may soon be published. The name "Longview" was first applied by Butts6 in Alabama.

Jan 1, 1949

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By K. C. Mills, E. T. Turkdogan

The results on the rates of vaporization of Fe-Ni alloys, levitated by an electromagnetic field in a stagnant atmosphere of helium, are shown to be in close agreement with those predicted theoretically. AS shown in Part I of this series of papers, the rates of vaporization of metals enhanced by convection currents are increased further by the process of condensation of metal vapor when there is a steep temperature gradient in the boundary layer. At the time this theoretical work was completed one of the authors (K. C. Mills) had already carried out some experimental work on the rates of vaporization of molten Fe-Ni alloys. The experimental work was done under conditions which make it possible to compare the experimental rate data with those predicted on theoretical grounds. EXPERIMENTAL The object of the experiments was to evaluate the activities in a number of binary metal systems. The details of the experimental technique are given in another paper by Mills, Kinoshita, and Grieveson,2 and, for the present purpose, a brief mention of the relevant features of the experimental method will be adequate. Using an induction coil, the metal weighing about 1 to 1.5 g was levitated by the electromagnetic field in a stagnant atmosphere of pure helium. The helium was freed from oxygen and water vapor in the usual manner, and its pressure in the vaporization chamber was maintained at 1 atm through a bleeder device. The vaporization chamber consisted of a pyrex tube, 2.8 cm diam, with a side arm connected to the helium bleeder. The bottom of the tube, shaped conical, was surrounded by the induction coil, and the top was sealed with an optical flat for the purpose of measuring the melt temperature with a two-color optical pyrometer. By suitable adjustment of the high-frequency power input, the metal was brought to the desired temperature in about 30 sec of levitation. After a specified vaporization time, e.g., 3 to 4 min, the alloy was quenched by switching off the power. The amount of metal vaporized was determined from the difference between the initial and final weights of the sample. During the vaporization time, temperature fluctuations of about ±10°C were observed. COMPARISON OF EXPERIMENTAL DATA WITH THEORETICAL VALUES The experimental results are given in Table I. As already mentioned, the attainment of the vaporization temperature took about 30 sec from the moment of levitation. Therefore, the times recorded in Table I are 30 sec less than the total time; this is considered to be a reasonable estimate of actual vaporization times.

Jan 1, 1964

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By S. G. Valentine

BLAST-FURNACE blowing engines are broadly of two main types: either steam- or gas-driven reciprocating engines, or turbine-driven rotary engines. Some results of experience with a furnace blown by an engine of the latter type may be of sufficient general interest to relate. The first engine of this type was installed at Oxford Furnace, New Jersey, before the writer's connection with this plant, in March, 1910. This furnace uses chiefly New Jersey magnetites and had been in blast seven months on its old engines when the turbo blower was started. It was 80 ft. high by 17 ft. 6 in. bosh and 11 ft. hearth diameter. It is of interest to see from the records what happened when the turbo engine was put to work. But of course, as the old blowing equipment was rather antiquated, consisting of two I. P. Morris engines with air cylinders 72 by 72 in., in good running order, however, it is evident that the comparison between their work and that of the turbo blower cannot be interpreted as being between machines that were respectively of equal excellence as representatives of their types. Still the results were gratifying and -interesting. The records show that, with the old engines blowing 13,630 cu. ft: of air per minute, measured by piston displacement, the furnace was working up about 480 tons of stock per 24 hr. and producing an average of 132 tons per day and a maximum of 166 tons. The rotary blowing engine installed was a General Electric Co. machine, the driving end being a Curtis steam turbine and the air end a six-stage rotary compressor, all running at about 1,500 to 1,600 rev. per minute, and having a capacity of 25,000 cu. ft. of air per minute up to 25 lb. pressure, and equipped with an automatic constant-volume variable-speed governor. After running this blower, for a period equal to that covered above by the old engines, at an average rate of 15,000 cu. ft. of air per minute, the furnace worked up an average of about 592 tons of material and produced an average of 170 tons per day. Thus, on an apparent increase of 10 per cent. in the air volume there was an increase of about 23.5 per cent. in the materials worked up and of about 28.8 per cent. in the product. For the first calendar month's operation of the turbo blower, on an average of 15,040 cu. ft of air per minute, there is

Jan 2, 1914

By A. A. Collins

OF widespread interest to all lead metallurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process. † Older Methods Three older methods, i.e., 1. Dross plus siliceous ore and limestone. 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and anti- mony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from I to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about impossible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it was decided to experiment with the soda process. The Soda Process After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other sugge~ted the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1949

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By G. A. Crowe, W. T. Bishop

WHILE the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,2 by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,3 cadmium,3.4 cobalt,4 copper,3-9 gold,10 iron,3,11 lead, 3,12,13 molybdenum," nickel,4.8,9 tin,15 and zinc3,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. PRINCIPLE OF THE METHOD The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1946

By C. E. Berry

NATURAL stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may he lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. MATERIALS TESTED I. Belgian Silex.-Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.-Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.-Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.-Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1946

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3'4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946