Search Documents

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module [(Fig. 1)]. The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information.

Jan 1, 1985

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

Smoky Valley Mining Company, Round Mountain, Nevada, was the pioneer operation designed for large scale heap leaching of crushed gold ores. It is located in the Big Smoky Valley which stretches 160 km (100 miles) through central Nevada west of the Toiyabe Mountain Range. Gold was first-discovered at Round Mountain, 88 km (55 miles) north of Tonopah, in 1905; and mining in the area included placer operations, which ran from 1946 to about 1960. Smoky Valley Mining Company is a partnership of Felmont Oil Co., Case-Pomeroy & Co., and Copper Range Co., with the latter being wholly owned by Louisiana Land and Exploration Co. In 1969, an option on the Round Mountain property was acquired by Copper Range, and during 1974 a decision was reached to proceed with mine development and plant construction. Ore reserves were reported at 10,537,000 mt (1 1,617,000 st) of 2.09 g per mt (0. 061 oz per ton) gold using a cut- off grade of 0.69 g (0.02 oz). Silver content was approximately 2.4 g per mt (0.07 oz per ton) and the waste to ore ratio was about 1: 1. By the end of 1976 heap leaching was in operation. The ore is a rhyolite tuff, sometimes described as a gold porphyry with highly abrasive qualities but which does not break down into slimes upon contact .with cyanide solutions. Gold is unevenly distributed through the ore but as a whole it is in a very finely divided state. Climatic conditions are extreme in central Nevada. Summers are hot and dry while winters are windy and cold with subfreezing temperatures. Elevation of the property is about 1,920 m (6,300 ft). Precipitation averages 203 mm (8 in.) per year. Until February of 1980, leaching was continued until the temperature reached minus 2ºC (28º F), and about 10 months leaching was the average. Water for the operation is drawn from the Toiyabe Mountains through a 13. 7 km (8. 5 mile) pipeline, originally installed in 1915, or from wells in the valley bottom. The plant requires make-up water at the rate of about 1,500 liters per min (400 gpm). On a schedule of three shifts, seven days per week, the daily output at Round Mountain amounts ,to 12, 700 mt (14, 000 st) consisting of 6,350 mt (7,000 st) each of ore and waste. Ore is hauled with a fleet of 45 mt (50 st) trucks and dumped into the 1,0.70 by 1,650 mm (42 by 65 in. ) gyratory primary crusher located near the pit. The primary

Jan 1, 1981

By Paul Hunt

UP TO June, 1923, the Park-Utah mine had shipped about 94,000 tons of a direct-smelting ore of a gross value of $4,200,000, or about $45. a ton. These values were in gold and silver only, although the ore carried small amounts of lead, copper and zinc. Freight, treatment and deductions had averaged $15.40 a ton. At the expiration of the Pittman Silver Act there was in sight about 30,000 tons of a similar ore with a gross value of about $15 a ton in gold and silver, and a large body of partly developed lead-zinc ore of a gross value of about $20 a ton, 40 per cent. of which was represented by the lead-zinc content and the balance by the silver and gold. Mine costs had been high during the life of the Pittman Act, but as a large part of the profits had gone into equipment of the mine and the orebodies were large and had good walls, we knew that mine costs could be greatly reduced. We were therefore faced by the necessity of getting lower freight and smelter rates or of concentrating the ore. We did obtain better freight rates on lower grade ore, and a favorable smelting rate on the small tonnage of siliceous silver-gold ore, but this smelter rate could not be applied to the lead-zinc ore with any profit to ourselves. The Judge mill of the Park City Mining & Smelting Co., with which we were affiliated, was running to capacity; if we built our own mill it meant a 5-mile freight haul to a satisfactory millsite and a year's delay. Fortunately, the International Smelting Co. had just inherited a mill at Tooele which, with some changes, was about double the capacity required for its own ores. Flotation tests were run on Park-Utah ore and a contract entered into with a low base treatment charge per ton, the tariff being largely fixed by the metallurgical deductions. This contract has been admirably calculated so that the miner can follow a lean orebody to its limit. Such a procedure has no doubt made it difficult for the smelting company at times, but it has resulted in finding ore extensions that otherwise might have been missed, so in the long run it has profited too. A flat rate per ton would have been like mining up to the claim endlines in a great many of the stopes. In order to offer such a contract it can be inferred that the smelting company must have been able to make high recoveries and high-grade products on a very lean ore.

Jan 1, 1928

ASDIE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows: the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. Robert W. Hunt Medal and Prize The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered by the Iron and Steel Division. Awards of the medal have been made as follows: 1920—Robert Woolston Hunt. 1926—Charles Lewis Kinney, Jr. 1928—John A. Mathews. 1929—Edgar Collins Bain. J. E. Johnson, Jr., Award This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-chairman

Jan 1, 1929

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By T. E. Leontis

Several publications1-7 during the past few years have demonstrated the markedly greater effect of cerium, as compared to all other alloying elements, in enhancing the strength and creep resistance of magnesium at elevated temperature either with or without the presence of other elements. In the work reported in Ref. 1-6, the cerium was added in the form of Mischmetal, which contains all the rare earth elements in essentially the same proportions as they occur in monazite sand, the principal ore of these metals. Mellor and Ridley7 have presented the creep characteristics at 200°C of magnesium alloys prepared both with pure cerium and with Mischmetal. Up to the present time, however, no comprehensive study of the effect of the various component elements of Mischmetal on the properties of sand-cast magnesium has been made. This hiatus in magnesium technology undoubtedly is associated with the difficulty in obtaining the rare earth metals separately. This investigation provides such a survey, the object of which was to determine which of the elements present in Mischmetal contributes the greatest effect in developing high strength and high resistance to creep at elevated temperatures. Toward this end the compositional variation of these properties has been determined as a function of temperature in the following alloy systems: 1. Magnesium-Mischmetal 2. Magnesium-cerium-free Misch- metal 3. Magnesium-didymiuin 4. Magnesium-praseodymium- lanthanum 5. Magnesium-cerium 6. Magnesium-lanthanum This designation, based on the names of the metals as furnished by the producer, is used throughout the paper in order to avoid the complicated system of listing all the elements present in the more complex alloys. The composition of the metals and the alloys is discussed in detail below. Preparation of Alloys ALLOYING INGREDIENTS The chemical composition of each of the six alloying ingredients used to prepare the alloys reported in this paper is given in Table 1. In each case, the percent total rare earths, percent cerium, percent neodymium, percent praseodymium, and percent thorium were determined in addition to the listed impurities. The percent lanthanum was determined by difference from the total rare earth content and consequently includes the other elements (samarium, terbium, yttrium, etc.) present in Mischmetal. These additional elements, however, seldom amount to more than 1 to 2 pet of the total rare earth content of Mischmetal. The iron content of the Mischmetal is considerably lower than that of the other metals. This grade of Mischmetal is now readily available. The metals are listed in the order of decreasing complexity. Elimination of the cerium from Mischmetal results in what the trade calls "Cerium-free Mischmetal." Carrying the separation a step further by eliminating the lantha-

Jan 1, 1950

By F. S. Norcross

MANGANESE has long been considered one of the United States' most important strategic raw materials. Its indispensability in steel manufacture makes it vital to the nation's industrial life. Coupled with this indispensability is the fact that domestic producers have not been able as yet to supply more than a small part of the nation's manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is consumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevailing prices. Dependence upon foreign sources thrust the United States into serious difficulties during the World War. At the start of hostilities in 1914, the nation was obtaining about four-fifths of its ore from the Eastern Hemisphere. Domestic production had been negligible, amounting to only 3000 to 7000 tons a year. As the war continued, shipments from the East, endangered by sea attack and blockade, dwindled rapidly. Imports from Brazil mounted. In this grave emergency, the United States, starting almost from scratch and under the stimulus of high prices, succeeded by 1918 in producing a peak of 311,000 tons, about 3 5 per cent of its consumption that year. Since the war, the United States has depended upon foreign sources for more than nine-tenths of its high-grade ore. During 1936, 1937 and 1938, imports for consumption averaged 736,000 tons a year. During the same period, domestic shipments averaged 21,000 tons a year. Of the imports, the U.S.S.R. accounted for an annual average of 280,000 tons, the Gold Coast 208,000 tons, India 74,000 tons, and Brazil 72,500 tons. But India and Brazil, which in 1936 ranked third and fourth in the list of importers, were displaced in 1937 and 1938 by a new and much nearer source-Cuba. From less than 1 per cent of United States imports in 1931, the island republic increased its shipments to more than 27 per cent in 1938. Cuba's average for this three-year period was 97,000 tons, and its total for 1938 was 131,000 tons.

Jan 1, 1940

By M. D. Hassialis

THE claim is made in a number of patents1,2,3,4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S¬R[=]-R’ (where x = r,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using Biphenyl sulphide, ditolyl disulphide and dinapthyl disulphide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed was that of Moses, Hess, and Perkins. A sample of ore weighing 500 grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a 2-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8: 1. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of 12: 1. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. CONTACT-ANGLE TESTS In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcocite, chalcopyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

E. P. Pfleider, University of Minnesota I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. R. H. Merrill, U. S. Bureau of Mines, Denver Federal Center The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability. G. A. Leonards, Purdue University I was interested in Mr. Lane's observations concerning the correspondence between rate of slide movement with rise of reservoir. Perhaps the most interesting feature is that the rate of movement at the time the rock slope failed was less than the rate at an earlier time when it did not fail. This is difficult to explain from current slope stability theory. K. S. Lane, U. S. Army Corps of Engineers I believe that reduced rate of movement is the result of the progressive type of failure, such as described by Patton and Deere. which occurs along the sliding surfaces. It is difficult to analytically define the progressive failure condition for inclusion in slope stability conditions, but its existence should be recognized in design. We should also realize that many apparently stable slopes undoubtedly contain overstressed regions. To design a slope with no overstressed region would be uneconomical and conservative. D. H. Deere I would pose the question-"What is the meaning of a factor of safety of one?" We were involved in the design of a large, irregularly shaped, underground cavity with an unsupported span of several hundreds of feet. Tests on rock specimens indicated a strength of 1300 lb per sq in. The RQD would have been between 90 to 100 percent indicating excellent structural continuity. In-situ stress determinations indicated an approximately hydrostatic state of stress at a level of 1400 lb per sq in. Calculation of stress concentrations at the walls indicated that the stresses there would be about 3000 to 4000 lb per sq in. Admittedly the rock is in a confined condition everywhere except at the very skin of the wall and the rock walls would thus on the average be somewhat stronger. Allowing for the effect of restraint the factor of safety was found to be less than 0.5 over a region several feet into the wall. Construction was started, using rockbolts only to support the walls. Failure around the immediate skin occurred after each

Jan 1, 1967

By J. E. Gould, H. J. Hand

MANY independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final deoxidation In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding over-deoxidation to minimize the amount of inclusions present and to make as sound a steel as possible For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or long FeO values The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishing the state of oxidation at a given time Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors Data obtained are from actual furnace operations, the metal test being of the spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States Steel Corporation This method of taking open-hearth metal temperature was invented by Collins and Oseland,1 and was developed into its present form by L 0 Sordahl,2 of the Research Laboratory The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications 3,4,5 Slag components were obtained by chemical analysis Data were taken from four 165-net-ton furnaces during the working period of the heat Recognizing that additions of ore affect the

Jan 1, 1942

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral rutile. United States consumption of titanium dioxide in concentrates for these applications in 1982 was as follows: pigments, 630,000 st; titanium metal, 31,000 st; and welding rod coatings, 5,000 st. The only commercially important titanium ore minerals at the present time are ilmenite and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) stated that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlined the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during that time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, VA, and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, FL, for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for low-grade sands, led to a return of activities in this area. The large deposits near Tahawus, NY. were brought into production in 1942 by National Lead Co. (now NL Industries, Inc.), and by 1949 this company was the leading producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec. The large Trail Ridge sand deposit in Florida was discovered by E. I. du Pont de Nemours & Co., Inc. geologists in cooperation with the US

Jan 1, 1983

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

Rates and patterns of gas flow in an experimental blast furnace were investigated by measurements, at three levels, of gas compo-sitions and temperatures and by direct determination of gas transit time by a new method employing mercury vapor as a tracer. Infer-ences were drawn about localized reaction zones and the mechanism of the onset of' channeling. LACK of precise knowledge of the nature of gas movement in the blast furnace has always been an impediment to better understanding of the blastfurnace process as a whole. The effects upon operation of various types of charge distribution are very largely brought about by the modifications to gas flow which they occasion. Intelligent evaluation of these effects demands a better understanding of the factors influencing gas flow and the ways in which the flow pattern is altered by conditions existing in the stock column. The same knowledge is required before a fundamental approach can be made to the problem of establishing optimum lines for new furnaces. An experimental furnace is operated at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Advantage was taken of experimental operation to conduct an investigation to develop and evaluate methods of study which could be applied later to industrial furnaces. The gas composition and temperature determinations were made as a preliminary study so far as gas flow was concerned but yielded significant information relating to other processes occurring within the furnace. The direct measurement of gas transit times by the mercury-vapor method constituted the major object of the investigation. Development of the mercury-vapor method was carried out while the data on gas composition and temperature were being collected. A complete description of the principle and development of the mercury-vapor method is beyond the scope of this paper but is available elsewhere. The results obtained and some consideration of the method's effectiveness and its potential value in the study of industrial problems will be treated here. DESCRIPTION OF FURNACE The general lines of the experimental blast furnace are shown in Fig. 1. The hearth diameter was 3 ft at the beginning of the investigation, and this was later enlarged to 3 ft 9 in. and finally to 4 ft to increase capacity. Tuyere to stockline height is 21 ft 4 in. The bosh depth is 3 ft 4 in. over which it opens to a width of 5 ft, and this diameter is carried up for 2 ft in a cylindrical section. The inwall batter of 1/2 in. per ft. is considerably less than in larger installations This may have influenced the movement of gaseous and solid materials. The furnace is inside a laboratory building and is charged from outside by a skip and hoist. Feeding into the first of three bell chambers, the stock is distributed by rotating the upper bell, the other two being used to obtain an effective gas seal. Three water-cooled tuyeres, with a nozzle dia-

Jan 1, 1960