Search Documents

By J. H. Hollomon, J. C. Fisher

The fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actua1 and the theorcticallY computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commcrcinlly available materials. Computatiolls have been made,,2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most importallt of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect conccrns the relation between deformation and the stress required for fracture, Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior com-pressive deformation, This marked ani-sotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffe, et al.3 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence, of the measured fracture stress from the theoretical value, the size effect, and the ergence of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the clement of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only docs the magnitude Of the Fracture stress depend upon the size and shape of these particles. but also its dcpendencc upon strain is affected by changes in 'hap' an' size Or the particles. The precipitate resulting from the age hardening Of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends 0' the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrate' by Griffith4 '0 arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of suficient magnitude to raise the stress at this location to a value comparable with the theoretical strength Of the material. If the cracks were reduced in size, Griffith showed that the observed fracture slrength the by virtue Of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

Jan 1, 1971

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By Sam Tour

OF the new alloys achieving commercial prominence during the year, an aluminum-silicon magnesium casting alloy, which is similar in many respects to the 4 per cent copper alloy, developed about 1921, which has attained such a wide field of service, may be mentioned. The new alloy, like the old, is a heat-treatable type and develops about the same physical properties. The alloy casts easily and is relatively insensitive to high pouring temperatures. Its ability to produce substantially leak- proof castings is noteworthy. A second casting alloy development is the new Aluminum Co. of America No. 132, "Lo-Ex" piston alloy, a result of nearly eight years of research. The alloy contains about 14 per cent silicon and varying amounts of nickel, copper, and magnesium. It exhibits a low coefficient of expansion and thus permits small piston clearances. Its lower specific gravity is a further advantage.

Jan 1, 1932

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

By W. O. Hotchkiss

RECOVERY and profits in the mining business do not go hand in hand. Some part of an orebody can usually be recovered at a lower cost per ton than the whole orebody or a higher proportion of it. Similarly, the total of the profits that may be made from mining an orebody is in itself not a true measure of the value of the business. The yardstick for money value should be present worth, and this is particularly so for purposes of com-parison. A simple example, well within the bounds of practicability, illustrates these points: Assume a mine to have known ore reserves of 4,000,000 tons. The ore is of uniform grade but is so situated that 1,000,000 tons could be mined more cheaply than the remainder. Present operations are on the basis of complete recovery of the ores. Output is 100,000 tons per year at a profit of $1 per ton. It is estimated that the 1,000,000 tons of readily accessible ore could be mined at the same production rate but at a profit of $2 per ton. For an output of 100,000 tons each year at a profit of $1.00 per ton, the mine will have a life of 40 years; will produce $4,000,000 of total profit, and, at Hoskold rates of 8 and 4 per cent, will have a present value of $1,104,690. If only the easy one-quarter of the ore is considered, with an output of 100,000 tons each year, at a profit of $2.00 per ton, that part of the mine will have a life of 10 years, will produce total profits of $2,000,000, and at rates of 8 and 4 per cent will have a present value of $1,224,800. . Under conditions such as these, then, one-quarter of the reserve ore promptly mined is worth some 10 per cent more than the entire reserve would be on an average basis extending over the longer period. Assume further that one-half, or 2,000,000 tons, of the reserves could be promptly mined at the same yearly rate of 100,000 tons at a profit of $1.50 per ton. Then this part of the mine would have a life of 20 years, would produce total profits of $3,000,000, and would have a present value of $1,320,630; approximately 20 per cent greater than for the whole ore-body on an average basis for the longer period.

Jan 1, 1936

By J. M. Markowitz

The movement of hydrogen in two-phase Zircaloy-2 under the influence of a thermal gradient was studied in specimens of cylindrical geometry. A gross displacement of hydrogen toward the cooler regions of the specimen was observed with consequent copious precipitation of 6-ztrconium (ZrH) there. The kinetics of the diffusion are analyzed and discussed. X HE temperature-gradient redistribution of hydrogen in a-Zircaloy-2 has been treated both theoretically and experimentally Hydrogen moves toward the cold side of the temperature gradient until a steady state has been established; tendency for further hydrogen movement because of temperature differences is nullified by the tendency to move in the reverse direction because of the concentration gradient. The steady state condition is described by the equation in which iV is the concentration of hydrogen at a point in the specimen corresponding to absolute temperature T, R is the gas constant,k is a constant of integration, and Q is a parameter called the heat of transport, characteristic Of the particular system. The value of Q has been determined for hydrogen in Zircaloy-2 by several investigators, using Eq. [11. There is considerable variation in the results, the cause of which has not been resolved; reported values lie in the range 3 to 6 kcal per mole. The physical situation for two-phase thermal migration is much more complex. The -phase boundary for the solubility of hydrogen in Zircaloy-2 ranges from a concentration of 25 ppm at 200°C to a maximum of about 600 ppm at 550°C.4a Thus, if the concentration of hydrogen in Zircaloy-2 is sufficiently great (>600 ppm), the specimen will be entirely two-phase, consisting of a matrix of a-Zircaloy-2 surrounding particles of zirconium hydride. At time zero, with a temperature gradient imposed, the relative amounts of hydride and a-phase in each infinite-simally thin isothermal section of the specimen can be determined from the phase diagram by the lever rule. Moreover, the concentration of hydrogen in the matrix phase varies from point to point, following the a solubility line. Over most of this temperature range (<450°C) 6 phase, Fig. 3, has a constant concentration.5 The diffusion rate toward the cold side should be governed by 1) the slope of the a solubility line and 2) the temperature gradient, The extra complication of two-phase thermal diffusion lies in the fact that migration of hydrogen would leave the a-phase concentration gradient unaffected, since it is fixed at any temperature only by the solubility; gross concentration changes would reflect only the relative amounts of matrix and hydride, which could vary continuously at every point. Migration of hydrogen out of a region would lead to dissolution of hydride, and

Jan 1, 1962

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1893 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management ` 188, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Haward-Canfleld Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By Charles Pack

EXTENSIVE progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,1 the author defined die castings as "metal castings made by forcing molten metal, underpressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, "slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to descriptive names, have adopted the name of spritzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1930

By Charles Pack

Extensive progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,l the author defined die castings as "metal castings made by forcing molten metal, under pressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, L&apos;slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to desecriptive names, have adopted the name of sprilzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1931

By S. B. Christy

The fact that many millions of gold have been extracted by the cyanide process, during the last five or six years, from South African tailings which could not be profitably worked by any other method previously tried upon them, lends a peculiar practical interest to this branch&apos; of metallurgy. Numerous writers have recently made valuable contributions on the process without exhausting the many complexities of the subject. Among the first American writers on the subject in its modern aspect were two former students of the University of California, Mr. Louis Janin, Jr., and Mr. Charles Butters. Young Janin was one of the first to enter this field, and performed much useful experimental work in the early stages of the history of the process. At about the same time, Mr. Charles Butters, who had left California to erect chlorination works for the Robinson mine at Johannesburg, became interested in the cyanide process, and, after getting the chlorination plant in working order, put up, for working the tailings from the Robinson mine, a cyanide plant which achieved the first large-scale success ever made with this process. The papers which Charles Butters, together with John E. Clennell and Edgar Smart, have contributed on the chemistry of the process, were among the first to give any adequate idea of its nature.* Another important contribution to the literature of the subject is the paper of Dr. A. Scheidell, published in 1894 as a " Bulletin of the California State Mining Bureau." This contains an admirable summary of the state of the art at the time of its publication.

Jan 1, 1897

By Charles Will Wright

I. INTRODUCTION. THE application of the camera as an adjunct to topographic mapping began practically with its invention, and it has been employed with varying success since that time. With the exception of the camera to be described, the plate-camera has been universally used in this work, thus giving a projection of the area photographed on a flat surface. From such projections or photographs, by the rules of geometry and of perspective, points defining topographic features and seen from at least two camera-stations may be projected upon a ground-plane-the map.1 In 1904 I employed the plate-camera for this purpose in Alaska, but found that the labor necessary to plot the maps, even in a general way, was long and tedious. In 1905 a small Eastman panoramic camera was fitted with spirit-levels, a sightalidade and a transparent scale, introduced inside the camera to register the degree-points in the sky-line of the film-negative; also, arrows to indicate the horizon-line. This was, on the whole, successful; but the details in the topography were not brought out in the views with sufficient clearness, and the photographs were too small. These difficulties were overcome by obtaining a larger and more carefully constructed instrument, which was satisfactorily employed in the field during the year 1906. A panoramic view is made up of an integral number of perspective views upon flat surfaces, and logically is the most ac-

Jan 1, 1908

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.&apos;s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By J. R. Linney

APPROXIMATELY 5,788,000 long tons of crude ore was produced by the Eastern magnetite industry in 1946, or a drop of 26 per cent compared -with 1945. Decrease in production -throughout the industry varied from :8 per cent for the mine with the lowest reduction to 49 per cent for the mine -with the highest reduction. At the Chateaugay mine, operated by :the Republic Steel Corp. at Lyon Mountain, N. Y., 426,900 long tons of crude ,ore was produced, yielding 129,500 long tons of concentrates or a reduction of 46 per cent compared with the previous year. Owing to a strike the mine was closed down from Jan. 21 to July 29. At the Mineville mines, also operated by Republic Steel, output was 755,000 long tons of crude ore or a reduction of 49 per cent compared with 1945. The yield from the crude ore production consisted of 51,500 long tons of lump ore and 380,000 long tons of concentrates. The Mineville plant did not operate from March 17 through July 28, on account of the strike. The Fisher Hill mine, which produced 93,000 long tons of crude ore, included in the above figures, has not operated since March 17, 1946.

Jan 1, 1947