Search Documents

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By E. A. Gulbransen, W. S. Wysong

The behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a a Or as an important component in alloys in high temperature Oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a micro-balance study of the following problems: (1) the oxidation behavior in the ternperature range of 25 to 550°C (') the reduction with pure hydrogen Of thin Oxide films formed On tungsten, and (3) the volatility Of thin Oxide films On tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the Oxide to to ratio is greater than one, the oxide is not considered protective, ('1 the meta1 readily Oxidizes at temperatures from 30" to 55o°C (3) the oxides WO² and WO³ are reduced at temperatures as low as 500°C. by hydrogen, and (4) the Oxide WO3 is volatile at temperatures from 800 to 1100°C. Literature The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°c. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides, Schei14 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bed-worth's5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.? They have reported that WO3 is the stable oxide in contact with the metallic substrate up to approximately 600°C while wo³ forms first at 7oo°c. Hagg and Magneli8 have recently reported a study of the lattice structures . observed in the tungsten oxidcs using the X-ray diffraction method. In addition to an a-phase WO3 and a '-phase WO2, they reported the existence of two new phases. A 8' phase, homogeneous between

Jan 1, 1949

By J. G. Mravec

The SO-called gas-tube method as developed by Hare, Peterson and Soler for determining the type and content of gases in molten steel is particularly adapted for determining the hydrogen content in molten steel. The development of this method has been quite completely discussed in a paper published by these co-workers in 1937.' The purpose of this paper, therefore, is to familiarize with this method those who arc not well acquainted with it. The principle of the gas-tube method is as fol1ows: One end of an evacuated gas tube is sealed with a very thin copper disk. when this end of the tube is immersed in a test spoonful of molten steel, the copper disk melts almost immediately, allowing a portion of the steel to be drawn up into the evacuated space. Any dissolved gases, and those produced by reactions between the components of the steel during freezing, are liberated into the unfilled portion of the sampling tube. A blob of steel that forms on the immersed end of the tube after the sample is drawn up seals up the end, making it airtight again. The evolved gases are subsequently drawn out of the gas tube through a suitable valve and analyzed by means of an Orsat apparatus. The volume of the sampling tube is sufficiently large so that a pressure considerably below atmospheric is produced after the gas evolution. The low pressure is necessary to effect a nearly complete removal of gases from the steel. Construction oF Sampling Tube The sampling gas-tube apparatus is illustrated in Fig. I. Seamless S.A.E. tubing used for section A is first cut into 7-ft. lengths. Through cxperiencc it was found necessary to use two sizes of tubing for this part, "is-in. and 3/4-in., respectively. The smaller tubing is generally used on the hotter or lower carbon steels. If the inside wall of the tube A is coated with grease or oil, it should be burned out before being machined as follows: One end is machined on the inside diameter to a depth of 34 in., so as to form a seat for a 7/8-in copper disk, which is stamped out from 0.005 to 0.007-in. thick copper sheet. The other end is machined on the outside diameter to a diameter of 1 5/16 in., to take a small reservoir or trap member I?. About 4 in. below the same end, a 1/2-in. hole is drilled to receive the 1/2-in. copper tubing leading to the large reservoir C. The inside of tube A is then thoroughly cleaned with a round wire brush, such as is generally used to clean out shotgun barrels. It is very important that the surface be absolutely free of rust or any nonmetallic coating. Next, the thin copper disk is soldered in place with low-melting silver solder.

Jan 1, 1945

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By D. W. Mitchell

While pure magnesium does not corrode rapidly the presence of even very small quantities of certain other metals accelerates corrosion remarkably. Because magnesium is such an electropositive metal (E° = +2.34 volts)' the presence of substances that permit galvanic activity is extremely undesirable. It is stated that as little as 0.017 pct of iron in magnesium causes a marked increase in the corrosion rate.2 Magnesium and its alloys are commonly melted in iron or steel pots; consequently the commercial metal has the opportunity to pick up iron if it has that tendency. Quantitative data on the solubility of iron in magnesium are of practical as well as of academic interest. Some magnesium alloy castings tend to have large grain size unless suitable treatment is given to the liquid metal just prior to casting. One method of grain refinement consists of "superheating" the metal just prior to casting. "Superhcating" is heating to a temperature 100 to 200°C above the casting temperature and holding for a short period of time. Superheated metal has a much finer grain than unsuperheated metal. A satisfactory explanation of this phenomenon has not been forthcoming. One hypothesis attributes the grain refinement in the superheated metal to precipitation of some phase that is mis-cible at the temperature of superheat but not miscible just below the casting temperature and which is thought to provide nucleating centers for crystallization. This phase, if the foregoing hypothesis is correct, would probably be a metal or an intermetal-lic compound. Of the metals likely to be found in magnesium alloys, iron is one of the most likely candidates for the role of grain refiner for iron occurs in small quantities in all commercial magnesium and magnesium alloys. A. Beck³ states that magnesium, in either the liquid or the solid state, cannot dissolve iron and that iron exists as a finely divided suspension which does not settle out because of its extreme fineness. Beck also presents a micrograph showing a large iron dendrite in magnesium but does not comment on the crystallization of iron from a solution supposed to contain none. It is doubtful that dendrite formation from suspended iron -would be possible. This suspension theory is the basis of patents4 covering the removal of iron from magnesium by allowing the iron particles to act as nuclei for the formation of primary magnesium crystals which can be separated by segregation. Also covered by patents is the removal of iron by the addition of another metal to form an intermetallic compound with the iron which, because of its increased particle size, is able to settle out of the molten metal. Here, too, quantitative information on the extent of iron solubility in liquid magnesium is of more than theoretical interest. M. Hansen,5 in his critical collection of the data on binary alloys, states that iron is not soluble in liquid magnesium. W. R. D. Jones% ho studied the physical properties of low iron magnesium alloys observed a 57°

Jan 1, 1949

By J. Leja, A. Pomianowski

This paper deals with equimolar solutions of xanthate and alkyl trimethyl ammonium bromide adsorption on copper, nickel and sphalerite powders. After an exposition of the experimental methods used and the results obtained, a thorough discussion leads to the conclusion that some molecular association between xanthates and CnTAB's does take place in the bulk of the solution as well as at the air/liquid interface. A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 to 400 mµ) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed, the half life of which was established as 29±3 days at 22°C and pH ~ 6. In mixed solutions of longer xanthate homologues (e.g. hexyl and nonyl) and equimolar CnTAB, colloidal precipitates are gradually formed which contain primarily the corresponding xanthate molecules. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 to 10"3 M solutions of KEtX alone and in equimolar mixtures of KEtX and CI2TAB. Presence of C12TAB caused a two to three fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and nickel powders (and in their rates of abstraction) but had no effect on the abstraction of xanthate by unactivated sphalerite (equivalent to less than a monolayer). The adsorption of C12TAB itself from the mixed solutions was very low, at most one monolayer only, and was not influenced by the nature of the solid powder used. A change in the rates of abstraction, observed with copper powder, was interpreted as a completion of a multilayer coating (completely enveloping the grains of powder) following which the rate of reaction between solution and substrate becomes controlled by diffusion through this coating. Work of Buckenham and Schulmanl on molecular associations between different collectors has shown unusual synergistic effects in flotation of individual minerals using mixtures of xanthates and alkyl trimethyl ammonium bromides. The objectives of the present work were: 1) to determine whether these molecular associations between the two types of collectors (indicated by strong surface tension lowering in Buckenham and Schulman's work) take place at the air/liquid interface only or in the bulk of solution as well 2) to establish whether different solids adsorb any species from the mixture of these amphipatic molecules preferentially or as molecular complexes 3) to establish whether there are any differences in the kinetics of adsorption. Metallic copper and sphalerite powder were chosen as adsorbents since they represent two extremes since copper readily adsorbs multilayers of xanthate (and is easily floated with ethyl xanthate) while unactivated sphalerite does not appreciably adsorb xanthate but is known to be readily floated by the amine type collectors. Metallic nickel was included because the infrared spectroscopic work2 on xanthate

Jan 1, 1964

By E. C. Carris

THE loading of bituminous coal mechan¬ically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous pro¬duction in the United States was loaded by mechanical means. During the past i6 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all¬time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase in mechanical cleaning. The importance of mechanical cleaning of coal was recognized many years before the mechanical loader was introduced, because of the impossibility of cleaning manually the sizes below 2 in., and the increasing competition from other fuels. Utilization of mechanical loaders without mechanical cleaning on the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely intro¬duced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problems have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expendi¬tures; the solution taking the pattern of rearranging and improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. LARGE IMPURITIES The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1946

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the. north-easterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By Martin S. Maier, H. R. Nelson

THE diffusion of metals plays an important role in many metallurgical processes, 1,2 as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystallization and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved.1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms-self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radio-activity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes-lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-10 and bismuth10 using natural radioactive isotopes, and of gold11 and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited on one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc, 14-16 silver,17 and copper.18 The second method was used for the work described in this paper. MATERIALS The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by 1/8 in. thick. Samples of high-purity copper described by Phillips and Skinner19 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to I700°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid,i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By W. E. Hess

AT the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed. Prior to the introduction of continuous miners the Pittsburgh seam at the Vesta mines averaged 72 in. of mineable coal, overlain with 12 to 16 in. of draw-slate, which weathers on exposure to air and is not firm enough to be held in place. Immediately overlying the drawslate is a wild or rooster coal, very irregular in thickness, varying from 12 to 30 in. Above the rooster coal the strata consists predominately of shales or lime shales and sandstone. Just before the introduction of continuous miners in the Vesta mines, however, a definite change took place in the character of the roof structure overlying the coal seam, see Fig. 1. Thickness of laminated roof immediately overlying the rooster coal varies with localities and introduces a problem in roof control. In fact, a set of eight main entries being developed in Vesta NO. 4 mine entered an area with so difficult a roof structure that management considered abandoning the section altogether. In this locality the roof consisted of thin alternate layers of roof coals and shales, with an occasional irregular seam of slick slate, the whole being laced with slips, and the coal itself being cut by clay veins and spars. In an effort to overcome some of the difficulties, roof bolting was introduced in 1949. This made it possible to recover coal from an area which otherwise would have been economically unmineable. There have been very few roof bolt failures. When conventional machines were replaced by continuous miners there were changes in the development of butt entries. By these changes it was hoped: 1—to speed development, 2—to provide as much solid coal as possible for the machine on retreat, 3—to avoid the necessity of crossing entries already driven, 4—to facilitate ventilation, 5—to provide a roadway for shuttle car haulage which would eliminate the necessity of running through doors or curtains, 6—to provide better roof control by increasing the distance between the center lines of entries, and 7—to provide more coal when the machine was in position to load.

Jan 1, 1956

By A. Dubé, G. Letendre, C. E. Beaulieu

An experimental study has been made of the time dependence of internal .friction and modulus of rigidity in- freshly quenched steels at room temperature. The effects of frequency, composition, and various thermal treatments are given. The kinetic 1aws observed cannot be fully explained by the so-called first stage of tempering and the transformation of retained austenite. It is suggested that the observed phenomena are due to the progressive immobilization of dislocations introduced by the martensitic transformation. It is generally agreed that the conversion of tetraginal martensite into cubic ferrite and ce-mentite occurs in three stages which at moderate rates of heating take place in the following temperature ranges:'-3 a) The first stage involves mainly a partial loss of tetragonality of martensite and the formation of ?-carbide between 95" and 175oC. b) The second stage consists of the decomposition of retained austenite between 230 and 290' C. c) The third stage covers the formation of ce-mentite between 290o and 400' C. The kinetic laws of these heterogeneous reactions have also been the subject of isothermal studies. Thus, Roberts, Averbach. and cohen3 report a very low reaction rate with a eutectoid steel at room temperature. For example, less than 10 pet of the contraction associated with the first stage is observed after 50 hr at room temperature. Hollonlon, Jaffe, and Buffum4 show that under the same conditions less than 10 pet of the tetragonality is lost. These results have led to the belief that martensite is a relatively stable phase at room temperature. On the other hand, it is well known that important structural changes occur in martensitic steels during the first few minutes at room temperature after quenching. This pretempering has at least two important consequences. In the first place, freshly quenched steels have a tendency to crack at room temperature, a fact which leads to the necessity of tempering as soon as possible after the quench. Another important consequence of pretempering a steel for short periods of time at room temperature is the stabilization of the retained austenite. Thus, as shown by Cohen,5 a very pronounced stabilization is effected with holding periods of 30 min at room temperature. Since these two effects are apparently not caused by the heterogeneous reactions mentioned above, they must be related to the rearrangement of structural defects within the martensite and retained austenite. According to the modern theory of dislocations, the shears required to effect the austenite-marten-site transformation may be realized through the motion of dislocations at the austenite-martensite interface and within the martensite plates.6 In this way, a martensitic transformation closely resembles a plastic deformation. In cold-worked solids, high concentrations of dislocations are left immediately after the plastic deformation and it seems reasonable to assume that appreciable densities of dislocations should also appear in the wake of a martensitic transformation. A considerable part of the high hardness of martensite would then originate in the obstruction of dislocations in analogy

Jan 1, 1961

By M. Muskat, H. H. Evinger

ALTHOUGH the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.1 In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was. measured and an attempt was made to determine the effectiveness of 'sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to determine the effect of tamping were performed by Snelling and Hall,2 Small charges (20 grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.3 The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.5 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By Falih Ergunalp

REGULAR production of chrome in Turkey started in 1860 with the operation of the Bursa deposits (5, Fig. I). Others were discovered at Makri, near Fethiye (3, Fig. I). For 33 years Turkey remained the principal source of this mineral. While new discoveries were coming in elsewhere, Turkey's output declined until 1921, as a result of four successive wars, which ruined the economics of the country. In 1927 a revival came with the production of 18,000 tons. In that year the Société Minière de Fethiye was formed. This company now operates mines in the Vilayets of Aydin, Denizli, Burdur and Mentese, and it has reached a maximum production of between 80,000 and 90,000 tons annually. The Turkish output therefore increased from 29,000 tons in 1930 to 55,000 tons in 1931; and to 119,009 tons in 1934. The second phase in the increase in chrome production in Turkey came about in 1935, when the Government decided to reorganize and control the mineral industry of the country according to the principles of "government control" of the present regime. Up to that time the mineral resources of the country had been exploited by private concerns. In 1935, the M.T.A. (Maden Tetkik ve Arama) Institute (Institute of Mining Research and Geological Survey) was established by the Government to do the geological and geophysical survey work and discover new mineral resources for the country. Before the establishment of the M.T.A. Institute, the chief chrome-producing region was Fethiye (3 and 4, Fig. I). As a result of the extensive work of this bureau, many new chrome deposits have been discovered and are now in production. The operational field of the mineral industry was given to Eti Bank, another Government-sponsored and Government-controlled establishment. Eti Bank gradually took over the exploitation of existing mines by purchasing them from privately operated companies. Attention was first given to the Zonguldak collieries and to the different chrome deposits scattered over the country. The Guleman mines (14, Fig. 1) were developed and put in operation in 1936. Since then the bulk of Turkish chrome output has come from this mine, which yields the highest grade ore in the world (averaging 52 per cent Cr2O3). In 1939, the recently discovered chrome deposits to the north of Eskisehir went into production, yielding ore having a Cr2O3 content of 51 to 52 per cent. Today, more than ever, the efforts of both the M.T.A. Institute and the Eti Bank are concentrated on finding new deposits and placing them in operation. There are still many promising regions of the country that merit systematic surveying and prospecting for chrome ores. Thus it is probable that Turkey will continue to make noteworthy progress in chrome output. As the annual chrome production of

Jan 1, 1944

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By E. V. Potter, H. C. Lukens

INTRODUCTION IN general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation' the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. APPARATUS The apparatus used in these investigations is essentially the same as that used in the manganese work' and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in ' gas volume are measured by volume gauge C which is essentially another mercury manometer in which . the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 61 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within ± 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. METHOD The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient time intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1948

By A. A. Watts, R. I. Jaffee, F. C. Holden, H. R. Ogden

Hypoeutectoid Ti-Cu alloys are responsive to heat treatment, and considerable variation of mechanical properties may be produced by transformation of the ß phase. Control of cooling rate, isothermal transformation, or quench tempering determine the transformation structure and properties. The transformation products are similar to those of carbon steel. THE equilibrium diagram for the Ti-Cu system has been studied by various investigators, and the most recent diagram is that determined by Jou-kainen, Grant, and Floe.' The titanium-rich portion of this diagram is reproduced in Fig. 1. The alloy compositions and annealing temperatures used in this work are shown. The Ti-Cu alloys containing up to 17 wt pct Cu are representative of an active eutectoid alloy system. Joukainen et a1.l have stated that ß phase cannot be retained on quenching and this has been confirmed in the present work. The similarity between the Ti-Cu system and the Fe-C system is evident and, as will be shown later, many of the transformation products appear to have similar microstructures. Heat treatments in this program were designed to produce the structures of primary interest for study and determination of mechanical properties. Experimental Procedures Preparation of Alloys: Five ½ lb ingots, ranging in composition from 0.8 to 6.83 pct Cu, were prepared by double arc melting in an atmosphere of high purity argon. Titanium melting stock was obtained from high purity iodide titanium, and copper additions were made from copper wire clippings. Segregation was reduced by inversion melting, in which the once-melted ingots were inverted in the crucible and remelted. The double-melted ingots were forged at 1600°F to ¾ in. diam rods, with both heating and forging operations being carried out in air. Surface scale was removed by grit blasting and grinding, after which the forgings were vacuum annealed at 900°C. The alloys then were swaged to ¾ in. diam rod at 750°C and test specimens were cut from this material. The vacuum annealing operation was to remove dissolved hydrogen, which is commonly present in the iodide titanium as-received. Although vacuum fusion analyses were not obtained for all these alloys, past experience indicates that the 6 hr treatment with a limiting pressure of 10- to 10-5 mm of Hg is sufficient to reduce the hydrogen level to 10 to 30 ppm. Vacuum fusion analysis of the 0.8 pct Cu alloy showed 19 ppm of hydrogen. In addition to the five hypoeutectoid alloys, three 15 g ingots were prepared with nominal copper additions of 9, 10, and 11 pct. Fabrication procedures were similar, except that these alloys were rolled to 0.040 in. sheet. Microstructure specimens only were obtained. Table I shows analyzed compositions and fabrication temperatures for these alloys. Heat Treatments: All heat treatments were made in potentiometer-controlled, resistance-wound tube

Jan 1, 1956

Book Review MEXICO UNDER CARRANZA. By Thomas E. Gibbon, Los Angeles, California. Doubleday Page and Co., New York, 1919, 270 pp., 711/2 X 5 in. $1.50. A vivid, accurate, convincing summing up of the Mexican problem as it confronts us today, devoid of sensationalism or bigotry. A compelling narrative of the relations of the Carranza Government and our own from Oct. 15, 1915, when it was recognized as the de facto government of Mexico, to the present time. It shows the absolute lack of promises kept or lived up to either with its own people or the United States. This is not done by invective or the indiscriminate use of adjectives but by quoting from the instruments on record on both sides of the case. The driving of the Red Cross out of Mexico, which condemned many of the native peons to starvation, and the interference with the Pershing Punitive Expedition are merely mentioned, but the crying crime against the Mexican people, who have sunk to unbelievable depths of misery obscured, but not exceeded, by the sufferings in Europe, is held up in a clarified light. Two illuminating chapters are devoted to the character and treatment of foreign investments in Mexico, Which are a complete refutation of the common statement that Mexico has been exploited remorselessly by the foreign investor. The conces-sions given by Diaz in the days of his regime most condemned are nowise as large nor the land grants as extensive nor the title so absolute as those granted to the railroad builders of our own transcontinental systems and other of our nationally subsidized works. This is not left to further argument but is settled by quoting the various official instruments and not at all in a tedious way. The author's concluding chapter is a picture of the Mexican people from Aztec times, when they had reached a civilization which gave them a better calendar than the Roman Empire ever had until modern times, to their present unhappy and pitiful condition. He concludes, basing his findings on parallel historical downfalls of a once proud people, that present conditions are the natural result of the absolute domination of an alien minority. He grants, of course, that there are many estimable Latin-Mexicans of integrity, ability and charm, but maintains that the dominant minority has continually degraded in fulfillment of the sociological law that the sure revenge of the servile class is found in the corruption of the master class. The book is replete with historical and literary allusions which, added to the pleasing style of the accomplished author, make fascinating the account of one of the world's great tragedies. Mr. Gibbon is a lawyer who has spent much time in Mexico and shows an understanding of the native people not shared by all writers on the Mexican problem. A distinct addition to all literature on the subject. P. E. B.

Jan 8, 1919

By M. C. Leverett, M. E. True, W. B. Lewis

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942