Search Documents

By R. E. Robbins, H. R. Brager

THIS note describes an unusual result obtained in an electron microscope investigation of cavities produced in commercial type 304 stainless steel irradiated in a thermal reactor (ETR) at 290°C to a high neutron flu-ence, 6 x loz1 n per sq cm. The analysis of the steel used is given in Table I. The unusual result is that the calculated quantity of helium gas produced by transmutation during the irradiation, 12 ppm, is less than one-tenth the amount of gas necessary to balance the surface tension of the observed cavities produced in the steel during ETR irradiation. Therefore, the cavities would be expected to behave like voids; however, they behave like "gas filled" bubbles. The maximum quantity of helium produced in the steel by B" transmutation was 8 ppm. In addition, the amount of helium formed by (n, (1) fast neutron reactions with the major alloy constituents and nitrogen was calculated to be 4 ppm based on the tabulated differential or effective fission-averaged cross sections of elements in type 304 stainless steel irradiated in typical thermal reactors.', In previous investigations concerning commercial austenitic stainless steel irradiated in a thermal reactor, the amount of helium gas calculated to be produced by transmutation has always been significantly greater than the amount calculated on the basis that the bubbles were gas filled, PPs= 2y/R. The balance of the gas was assumed to be in bubbles smaller than could be detected on the electron micrographs. Accordingly, the bubbles were attributed to helium produced from transmutation of impurity boron by thermal neutrons. These bubbles were not uniformly dispersed in the matrix but were located principally at grain boundaries, or were radially positioned around a few precipitates located in the matrix and at the grain bundaries., 4 Voids have also been observed in austenitic stainless steel irradiated at high temperature to high neutron fluences in the EBR-I1 and Dounreay Fast Reactors. The voids were uniformly distributed throughout the matrix. The amounts of helium gas produced by transmutation during these irradiations were less than one-tenth the amounts needed to balance the surface tension of the voids formed by the fast reactor irradiation. The fast reactor results are quite analogous to those reported here for the ETR irradiated steel. Electron microscope examination of the fast reactor irradiated material after a 1 hr postirradiation annealing at 900°C disclosed that essentially all the voids had been eliminated. The authors stated that the voids had developed due to the high concentration of vacancies produced during irradiatin., 6, ' The microstructure of the ETR irradiated material as-tested at 75O°C, Fig. 1, contained about 2 X lot5 cavities per cm3 with an average diameter of 110A. With the Van der Waals b correction and y = 1500 ergs per cm2, 300 ppm He would balance the surface tension of the observed cavities. Stereoscopic examination of the electron micrographs showed that the cavities were neither preferentially located near the grain boundaries nor highly concentrated at specific regions or precipitates. The cavities were nearly uniformly distributed throughout the matrix, on dislocations and at grain boundaries. These observations imply that the cavities were not the sole results of B'O

Jan 1, 1969

By C. W. Price, G. A. Wheeler

BERYLLIUM has always been a difficult material to prepare for metallographic examination. Severe surface deformation occurs during mechanical grinding and polishing, and a suitable bright-field etchant has not been developed. Certain electrolytic techniques produce satisfactory polishes, but these techniques have not yielded entirely consistent results. Furthermore, they have not provided satisfactory bright-field etches. The purpose of this paper is to describe an electrolytic polishing technique that can also provide an excellent bright-field etch. In addition to the bright-field etch, other advantages of this technique are excellent reproducibility, rapidity, and ease of polishing and etching. Experimental Technique. Specimen Preparation. Beryllium specimens may be either mounted or unmounted for the use of this technique, and the size of the specimens is not important. Specimens with surface areas up to 4 sq cm have been electrolytically polished and etched successfully with this technique. The most important requirement is to provide a good electrical contact to the specimens, preferably on the back of the specimens. When specimens are mounted, a hole is drilled through the back of the mount so that the specimen can be contacted with a probe. Conventional metallographic grinding techniques are used to prepare the specimens for electrolytic polishing. The specimens are ground on silicon carbide papers. Grinding through the usual series of papers down to the 600-grit paper is recommended to minimize the electropolishing time, although successful electrolytic polishes and etches have been obtained by grinding only through the coarser papers. A continuous flow of water is used during grinding to provide lubrication and to minimize contamination. Mechanical polishing is not required because high rates of material removal are achieved with the electrolytic polishing. Polishing. Most of the results reported in this paper were obtained with a "Disa-Electropol", manufactured by Struers Scientific Instruments of Copenhagen, Denmark. Satisfactory results have also been obtained with the conventional beaker technique of electrolytic polishing, however, the conditions applicable to both the Disa unit and the beaker technique will be described. Stainless-steel cathodes are used in both techniques. In the beaker technique, a flat cathode, with an area at least twice that of the specimen, is used, and the specimen is held parallel to the cathode. The distance between the specimen and the cathode affects the quality of the electropolish. This distance is set at about 7 mm in the Disa unit; the same distance produces the best results in the beaker technique. Specimen-cathode distances greater than about 20 mm produce considerable relief, while distances less than 7 mm cause high current densities that are difficult to control. An electrolyte of 2 pct HC1, 2 pct HNO3, and 2 pct HCIOl in ethylene glycol gives the most satisfactory results for both electrolytic polishing and etching. This electrolyte was developed by altering the composition of a similar electrolyte used for electrolytic lapping1 and adding HClOl to improve the etching characteristics of the electrolyte. Variations of from 0.25 pct to as much as 5 pct of each of the acids do not significantly affect the results, but the greatest amount of control and reproducibility can be obtained with the composition of 2 pct of each acid. Generally, lesser amounts of the acids produce lower polishing and etching rates, while greater amounts of acids cause high current densities that are difficult to control.

Jan 1, 1968

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952

By R. E. Maringer, B. A. Wilcox, A. H. Clauer, J. H. Sovik

Internal friction measurements from 25° to 1100°C have been made on specimens machined from TD nickel bar. The use of miniature torsional pendulum specimens alloived damping measurements to be made on specimens whose axes were parallel to the original bar axis, at 45 deg to the bar axis, and at 90 deg to the bar axis. There was a marked difference in damping with varying specimen orientation, and this was related to the pronounced micro structural anisotropy of this material. Varying the microstructure by cold working plus re crystallization annealing also greatly affected the damping behavior. Recrystallization essentially removed the broad peak found at 400° to 650°C in as-received TD nickel, and in addition greatly lowered the background damping. DlSPERSION hardened metals such as SAP-type alloys (Al + AI2O3) and TD nickel (Ni + 2 pet ThO2) have been developed primarily to improve high temperature strength properties. There have been numerous damping studies on SAP-type alloys,1"9 and one of these6 showed that the damping capacity was greater than that of 99.5 pet pure Al from 25° to 600°C. Several preliminary observations on TD nickel10 and an experimental Ni-ThO2 alloy11 indicated that here, too, the damping capacity was quite high. A high damping capacity in TD nickel, combined with its relatively good high temperature creep strength, could provide an additional benefit for some high temperature structural applications. This work was undertaken to study the internal friction behavior of TD nickel bar over the temperature range 25° to 1100°C. In Ni-ThO2 and Ni-Cr-ThOz alloys, other properties such as steady-state creep rate,12 creep rupture life,12'13 modulus of elasticity,14 and ultimate tensile strength,14 are sensitive to orientation with respect to the primary working direction. Thus, in order to examine anisotropy effects in damping, studies were made on specimens machined with their axes parallel, at 45 deg, and transverse to the original bar axis. MATERIAL DESCRIPTION AND EXPERIMENTAL PROCEDURES The material used in this investigation was from the same £ in. diam TD nickel bar that has been studied previously.13'15 The structure typical of the as-received TD nickel is shown in Fig. 1, and additional details of the structure can be found in Refs. 13 and 15. Elongated grains are parallel to the bar axis and are about 10 to 15 u long and about 1 u in diam. This structure is very stable, since no recrys-tallization or grain growth occurred after annealing for 3 hr at 1300°C.13 The total ThO2 content was 2.3 vol pct and the particles ranged in diameter from 100 to 1000. The average particle diameter was 370Å and the mean planar center-to-center particle spacing was 2340Å. To examine the influence of grain and subgrain structure on damping, a section of TD nickel bar was swaged and drawn at room temperature from 1/2 in. diam bar to 0.040 in. diam wire (99.3 pct re-duction in area). The structure in Fig. 2 resulted after the wire was annealed for 3 hr at 1250°C. The recrystallized grains were much larger than the grains in as-received bar, but still showed considerable elongation in the direction of working. A high

Jan 1, 1970

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.', ' Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds' of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies' of the slags, slag weights, the metal particle theory,' ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat' is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By A. L. Benham, W. E. Dowden, W. J. Kunzman

The mechanism involved in creating a miscible fluid displacement of typical reservoir fluids through porous media by light hydrocarbon mixtures usually involves a number of mixing and separation stages in the contact area. This mechanism has been illustrated on ternary diagrams for miscible displacement of reservoir fluid by rich hydrocarbon gases. A relatively simple method has been devised for calculating the approximate conditions for a miscible displacement of reservoir fluid by rich, light hydrocarbon gases or by LPG mixtures. Miscibility is favored by increased pressures, decreased temperatures, light reservoir fluids and light hydrocarbon-displacing fluids rich in the heavier components. The conditions for miscible displacements of five typical reservoir fluids by various light hydrocarbon mixtures were determined for a range of temperatures from 70" to 260°F and pressures from 1,000 to 3,000 psia. A correlation of these conditions was obtained using the variables of temperature, pressure, C,+ molecular weight of the reservoir fluid, C,+ molecular weight of the displacing fluid, and mol per cent methane in the displacing fluid. This correlation has been applied to data appearing in the literature with very good success. A partial check of the correlation has been made using a step-wise procedure with a windowed PVT cell. INTRODUCTION The term, "miscible fluid displacement", may be defined as any oil-recovery displacement process where there is an absence of a phase boundary or interface between the displaced and displacing fluids. A water flood would not be a miscible fluid displacement, although cycling in a condensate reservoir would be. Another example is displacement of oil by gasoline. Not so obvious, however, are the conditions under which fluids (such as propane, mixtures of propane and methane, or other similar systems) will give a miscible fluid displacement of oil. There are four standard miscible-fluid-displacement processes being used for the recovery of oil from an "nderground reservoir—(1) high-pressure dry-gas miscible displacement, (2) rich-gas miscible displacement, (3) miscible slug using a slug of LPG followed by a lean dry gas under miscible conditions, and (4) gas driven-slug process using a slug of LPG followed by a lean dry gas under immiscible conditions. The first problem faced by the engineer designing a miscible displacement process is to determine the conditions for miscibility. A number of papers have included discussions of the process of obtaining miscibility in these processes.1-8 However, methods for calculating the conditions for miscibility have not been published. This paper includes a method for calculating the conditions for a miscible displacement of reservoir fluid by a rich gas (LPG diluted with methane or natural gas). In this paper, a rich-gas miscible displacement process is defined as an oil-recovery process in the reservoir. The cost of a rich-gas miscible displacement will be decreased by diluting the LPG with methane or natural gas as much as possible. Therefore, it is important to be able to predict the maximum dilution for miscibility. MECHANISMS The mechanisms for obtaining miscibility between a displacing mixture of light hydrocarbons and displaced reservoir fluid often involve a number of displacing and mixing stages. As stated previously, the cost of a rich-gas miscible displacement is decreased by diluting available LPG with natural gas. The problem is to predict the maximum dilution allowed while maintaining miscibility. To get a picture of the displacing and mixing stages, it is helpful to consider these complex hydrocarbon mixtures as pseu do-ternary systems. Graphical representation of a complex system as a pseu do-ternary system can be thermodynamically rigorous if enough variables are used to describe the character of each pseudo-component in one of the phases. However, even if the characterization of each pseudo-component is not complete, pseudo-ternary representation does serve to illustrate the mechanism for obtaining miscibility and can be used to make some general conclusions concerning the conditions for obtaining miscibility. A phase diagram for the ternary system, methane-

By G. S. Rice

The subject of dust explosions in coad mines first appears in the Transactions of this Institute following the first great mine disaster that happened in…

Jan 1, 1915

By William E. Greenawalt

Ever since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydroelectric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods. Electrolytic methods are ideally adapted to hydroelectric development, for the load is constant throughout the full twenty-four hours, and the cost of both installation and operation of hydroelectric plants is not appreciably greater when operating for twenty-four hours than when operating for eight or ten hours; whereas, in fuel-power generation, as also in smelting, the cost is more or less in proportion to the fuel and power used. Nevertheless, fuel-power generation presents advantages in electrolytic methods, as the power plant may be located in a favorable place while the leaching and electrolytic plants may be located at the mine. The ultimate possibilities of the wet methods have yet to be determined. The possibilities of smelting have been thoroughly worked out; there is no unsolved major problem in copper smelting, and it has practically reached the limit of its possibilities. It seems hardly probable that any future improvement, either of method or apparatus, will greatly

Jan 1, 1924

By John G. Hall

MANY millions of tons of raw materials are removed each year from open pit mines in the eastern U. S. These materials are used by industry to produce aluminum, asbestos, barite products, building stone, cement, crushed stone, copper, coal, dolomite, garnet, iron, limestone, mica, phosphate, phyrophyllite, titanium products, and wollastonite. Improvements in open pit mining techniques through the years have made open pit mining more and more attractive as compared to underground methods. Today ore deposits that formerly would have been mined underground have proven to yield more profit if mined by open pit methods. Ever-rising labor and material costs have made equipment capable of high-volume production and low-unit cost-and supplies rendering low-unit costs-not only attractive to open pit operations, but essential to their economic existence. During the past year, the major advances have been in drilling and blasting operations, and the application of large capacity materials handling equipment. Mining men from the Great Lakes, Northeast, East Central, and Southeastern regions of our country tell in the following articles of the trends in open pit mining in their areas during 1956.

Jan 2, 1957

By G. Cartaud, F. Osmond

We have already devoted two previous memoirs to this question. In the firstL we collated and discussed the existing literature on the subject; in the second: we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allo-tropic states of iron—a, stable below A2; , stable between A2 and A3; and , stable above A3—all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, and did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier mas even led to think from some of our results that r-iron could very well be a rhom-bohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Jan 1, 1907

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33' API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By C. E. Lesher

Low-TEMPERATURE carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus 3/8 -in- or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal, of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic con-sumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold.

Jan 1, 1940

THE activity of the principal oil fields of Rumania followed the same course as in 1939. It was marked by (1) collaboration between the various companies, particularly in exploiting oil at great depths with a view to rationalizing the exploitation and decreasing the difficulties inherent in very deep drilling; and (2) economy in the exploitation of the older pools in reducing to a minimum the cost of the extraction and working over of wells by the concentration of productive wells in groups. The pooling arrangement continued at Tintea as a measure of conservation, and exploitation of the unitized region went forward on the basis of the norms established in 1939. The same methods were applied in the fields of Liesti, Ceptura and Boldesti. The petroleum industry had some difficulty in providing the necessary material and the hands for work. Importation of material and machines from the United States was virtually stopped. Substitutes were provided from Germany but particularly useful were certain dispositions made by the local metallurgical industry. Despite the higher cost of the production of local material and machines, they were superior to the German product, the difference in quality justifying the higher price charged as the materials were found to be particularly adapted for the purposes of the petroleum industry. The cost of production was still further raised by the work that was imposed for national defense. The rise in costs per meter drilled was 50 per cent over those of 1939. According to bimonthly tables furnished by the Moniteur du Petrole Roumain, the deepest well completed in 1940 was an exploratory well, No. 201 of the Concordia company, drilled at Tintea and suspended at 3338 meters. This depth was reached toward the close of 1939 and the well was not deepened in 1940 became of large deviation from the vertical. The record for productive wells had been held by No. 429 at Tintea, drilled by Unirea to a depth of 3200 m., and in 1938 well No. 317 Cocorasti-Mislea, of the Colombia company, but these records were passed in 1940 by well No. 613 Liliesti of the Con-cordia company, which reached a depth of 3294 m. and had an initial production of 10 tons per day. In 1940, the same number of wells, II, had been drilled to a depth of over 3000 m. as in 1939. Five of these wells are at Tintea and six at Liliesti. Table I lists these very deep holes in the order of their depth. Table i.—Deep Wells Drilled in Rumania in 1940 Initial No. Produc- of Company Field Meters tion, Well Meters Tons per Day 405 Colombia......... Liliesti 3,001 10 629 Unireu............ Tintea 3,005 73 426 Unirea............ Tintea 3,050 48 410 Colombia. ........ Liljesti 3,055 30 627 Concordja (Unirea). Liliesti 3,072 75 430 627ConcordjaConcordia (Unirea). (Unjrea 3,II9 30 618 Colombia......... Liliesti 3,168 70 24 Steaua Romana. . . Tintea 3,184 18 412 24Unirea............ Tintea 3,211 23 613 Concordia......... Liliesti 3,294 10 Production in Rumania in 1940 reached 5,813,000 tons, in contrast to 6,~40,0oo tons in 1939, a decline of 427,000 tons, or 6.8 per cent. Drilling reached 241,500 m., in

Jan 1, 1941

By Theron Wasson

The discovery of two new fields—the Reed City area of Osceola County and the Headquarters field, of Roscommon County —and the important development in Winterfield township, Clare County, again demonstrate the fact that it is the unknown and unexpected that enter very definitely into the oil-producing history of Michigan. This is particularly true in the area of thick glacial drift in the north central part of the state, where the new prolific fields have been discovered this year. This shifts the interest from the southwestern part of the lower peninsula, where a number of pools were rapidly developed during 1939 and 1940, back into the Central Basin area. As a result of strict proration in the new areas, the production for the state of Michigan for the year has not been as great as in 1940 or 1939. In 1941 the total production was 16,300,000 bbl., in 1940 it was 19,551,000 bbl., and in 1939, which was the peak year, it was 23,300,000 bbl. However, the discovery of the new fields this year nearly doubles the estimated reserves for Michigan reported at the end of 1940 In 1941 about 12,000,000 bbl. of oil was produced from the older fields, in which the individual well productions were so small that proration was not an important factor. The total production for the state from the discovery of oil in 1925 through 1941 now stands at 161,205,000 barrels. ActIVe Oil Fields Reed City Field.—In the Reed City field, Lincoln township, Osceola County, only small oil wells were completed during 1939 and 1940. The discovery of much larger production in wells drilled somewhat deeper, by The Pure Oil Co. and the Weber Oil Co., in the early part of 1941, led to the rapid development in this area. Some wells have had initial productions as high as 10,000 bbl. By the end of the year III producing wells were completed, with an average depth of 3600 ft., from the Detroit River formation of Devonian age. The entire development of the field to the end of 1941 was on 20-acre spacing. Headquarters Field.—The Headquarters field, which lies along the line between Clare and Roscommon Counties, was one of the most important discoveries of 1941 and will be the scene of vigorous development during 1942. Production so far has been from the Traverse lime at about 3400 it., and development has indicated that this is probably one of the most productive Traverse pools yet discovered. One well had been given a potential of 10,000 bbl. per day. Dry holes well located in relation to big producers indicate that it is a typical Traverse development. Winterfield Field.-This field, in Winter-field township, Clare County, was discovered late in 1940. By December 1941, 14 Dundee and 5 Traverse producers had been completed. The Dundee lime is found at a depth of 3750 it. and the Traverse lime at 3070 it. Producing conditions in the Dundee seem to be erratic because of varying porosity in the dolomit-ized limestone. Kawkawlin Field.—The Kawkawlin field, which was discovered by the Gulf Refining Co. in 1938, is in Monitor and Kawkawlin townships, Bay County. Small production

Jan 1, 1942

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By C. Feng

HE sensitivity of twinning in molybdenum alloys containing 20 or more at. pct Re was reported by Dickenson and Richardson&apos; and Sims et a1.&apos; The latter3 also studied the effect of twinning on plastic deformation of these alloys. Recently, in this laboratory, the twinning planes in a series of Mo-Re alloys were successfully identified by tracing their boundaries on two known surfaces of the crystals, with the aid of stereographic projection. The nominal alloy composition and the results of the determination are listed in Table I. Metallic powders of molybdenum and rhenium with 99.9 pct purity were mixed, pressed and arc-melted into buttons under purified argon in a water-cooled copper hearth; the buttons were annealed at 2400 °C in vacuum (10-&apos;mm Hg) for 1 hr, remelted under argon and finally reannealed in vacuum at 2400°C for another hour. This treatment yielded a homogeneous alloy. Large-grain specimens devoid of subgrains were obtained with grain diameter varying from 1/8 to 1/2 in. A typical specimen weighed about 15 g. Orientations were determined by taking X-ray back reflection photographs for each grain on a polished surface of the specimens. Two surfaces were cut and polished; the angle between the two surfaces was measured with an accuracy of *2o. The twins were produced by compression in a hydraulic press at room temperature. Usually, several sets of twins could be obtained within each grain. Except in cases where no twins were formed, (Crystals 7, 8, and 9) the twinning planes were identified consistently as the (112) family over a wide range of alloying compositions and surface orientations of the crystals, as indicated in the stereo-graphic triangle in Fig. 1. The twins, however, were not broad enough to accommodate a conventional X-ray beam and no identification could be made of the twinning direction. Nevertheless, the direction must be one that lies in a plane of symmetry perpendicular to the twinning plane. There are only two such possible planes in a bcc lattice, namely the (110) and the (100) planes. Of these, only the (110) planes are perpendicular to (112), and the <111> direction is the intersection of the two perpendicular planes. It can thus be concluded that <1l1> is the twinning direction. The twinning elements of molybdenum have been reported as the (112) planes and the <111> directions,4 which are also the operative elements in other body-centered-cubic metals, such as W, a-Fe, and ß -brass.5 Thus, the present finding of the twinning elements in Mo- Re alloys supports the concept that twinning formation is mainly governed by the lattice structure. It is of interest to note that for specimens containing 12 at. Pct Re or less, no twins were found after being plastically deformed to as much as 30 pct reduction in height by compression, while for the 35 at. pct Re alloy, twins were formed with less than 1 pct deformation. This, of course, does not exclude the possibilities that for Re-Mo alloys containing 12 pct Re or less, twins could be formed under different conditions, such as at liquid air temperature or under impact loading. The present results, however, suggest that under the same conditions twinning is increasingly sensitive with increasing rhenium content. Consequently, the plastic strain at which twinning starts was found inversely proportional to the amount of rhenium in solid solution with molybdenum. This plastic strain necessary to cause twinning may be used as a criterion in the study of twinning characteristics.

Jan 1, 1961

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.&apos; The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.&apos; The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930&apos;s.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940&apos;s. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.&apos; When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960