Search Documents

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By Albert G. Anderson

I'm sure many of you have wondered what the term "Cross Flow Filtration" means. I shall explain it so that you more clearly understand it, and I hope you will be able to make it a useful tool for you in the future. In the simplest form of cross flow filtration contaminated fluid. or feed stream, is fed at a high velocity down the center of a porous tube, clear fluid weeps through the porous wall of the tube while the suspended solids concentrate in and are swept away by the feed stream. (See figure A). The high velocity flow of the feed stream tends to keep the inside of the tube free from a build up of contamination. By utilizing this cross flow approach to filtration, we have been able to concentrate such things as paint pigments, titanium dioxide, iron oxide, precipitated metals such as uranium yellowcake or silver, cadmium, some metal hydroxides, as well as gelatinous particles such as yeast cells. You will recognize that cross flow filtration lends itself to a recirculation loop system due to the necessity of maintaining a high velocity on the inside of the tube. This means that we generally have a storage tank from which we are recirculating, and the solids will concentrate in the storage tank. (See figure B). The storage tank design becomes an integral part of the total system and is very important to the total function of the system. The cross flow filter system requires only low pressure, and will work with centrifugal pumps, diaphram pumps or in some cases no pump at all. As an example, if we wanted to filter a 10 GPM (37.8 liters/min.) stream that contained 1% of submicronic particulate, we would flow the 10 GPM (37.8 liters/min.) into the storage tank and recirculate through the filter at a flow of anywhere from 30 GPM to 100 GPM (113.6 to 378.5 liters/min.) depending upon the filterability of the particles from the liquid. As the contaminated fluid recirculates, the solids will build up in the storage tank and loop until they reach a level, which is dependent upon the design of the tank. Then the settling rate in the tank becomes equal to the amount of the solids being fed to the tank, and as a result you reach an equilibrium in the amount of solids being presented to the inside of the porous tubing. We have in effect created a dynamic settling tank or thickener. A flow of 10 GPM (37.8 liters/min.) of clear filtrate comes off for either recycle or disposal with periodic removal of thick mud from the bottom of the tank. The thick mud can be either processed through a centrifuge, a rotary drum filter. a flat bed pressure type filter, or other means. Often the small volume of filtrate from the mud de-watering stream can be recycled back into the recirculation tank so that any fines in the feedback are again concentrated, thus closing the loop on the continuous process 100% removal system. Cross flow filtration will not do efficient molecular separation. We work primarily with discrete solids but we do separate them totally from the liquid carrier fluid. I know some of you will raise your eyebrows when I say that we remove 100% of the particulate, but in measurement tests, we have measured the filtrate cleanliness with instruments that record as low as .05 ppm and the instruments read zero, so that it is less than .05 ppm.

Jan 1, 1980

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,' the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*' specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By R. M. Goldhoff, H. J. Beattie

The high-temperature properties of a 1 Cr-Mo-V forging steel are described. A series of controlled heat treatments was designed to delineate the effects of austenitizing and tempering treatments, temile strength, and grain size on such properties. Studies indicate that the mechanical properties and their varlations under creep can be described by the initial metallurgical structures and their changes droPirzg exposure, particulavly the carbide reactions. Such structures are described and correlated with the mechanical properties. FOR many years the large steam turbine industry has relied on the 1 Cr-Mo-V type forging steel for critical applications. Because of its adequate heat resistance and relative economy, it is currently in use in the temperature range up to about 1050" to 1075°F. Attempts to understand the large property variations attainable in this steel involve the structural modifications due to the wide latitude in its heat treatment. The heat treatment essentially involves a two-step process which includes solution-ing of carbides in the austenite range followed by a suitable tempering treatment below the critical to adjust the level of properties. The latter step is referred to as "secondary hardening" and is basically an ordinary aging reaction involving carbides. In the commercial heat treatment of large components of such steel, homogenizing and stress-relief anneals may be included and have some importance in determining subsequent properties. Several studies of the engineering properties of this steel as a function of transformation micro-structure have been reported.1 3 However, in this steel the carbide reactions, which are a function of composition and heat treatment, appear to be the property-controlling factor rather than the micro-structure defined as a transformation product. Thus, the tempering resistance of this type of alloy steel is mainly a function of the size and distribution of alloy carbides.4 However, it is also necessary to consider the stability of the microstructure and the effect of dynamic carbide reactions on subsequent properties. It is the purpose of this paper to show the interdependence of properties and corresponding structures, particularly carbide reactions, developed for a limited set of controlled heat-treatment conditions applied to 1 Cr-Mo-V steel. MATERIALS AND PROCEDURE The material for this work came from a large production forging whose chemical composition is shown in Table I. The property data accumulated on this steel as a function of heat treatment were room-temperature tensile and smooth- and notch-bar creep rupture at 1050°F (notch geometry: shank diameter = 0.357 in., depth = 50 pct, radius = 0.005 in.). To achieve controlled structural variations the temperature and time of both austenitizing and tempering were varied in a manner to produce a series of eight steels each at one of two grain sizes and one of two hardness levels in proper combination for valid comparisons. This will be clear upon examination of Table I. Structural studies involved the use of optical and electron microscopy as well as X-ray and selected-area electron diffraction. To reveal the nature of carbide precipitations, electrolytic extraction techniques were used with subsequent analysis of the residue by X-ray diffraction. Weight losses of the steel specimens during electrolysis were measured and successive chemical fractionations of the residues were applied and checked by X-ray examination. The details of fine structural distributions, morphologies, and crystallography of the precipitates as well as dislocation distributions were investigated by examining in the electron microscope three common types of preparation. a) Relief Replicas. Mechanically polished sections were etched in 2 pct nital, replicated with a nitrocellulose film, which was shadowed by chromium vapor deposited at a glancing angle of 20 deg. b) Extraction Replicas. A thin film of carbon was vapor-deposited on the polished and etched surface. The carbon films were then etched off and gathered on electron-microscope supporting grids. The carbides left imbedded in the carbon replica in their original distribution were then examined crystallo-graphically by selected-area electron diffraction. c) Thin Films. Specimens were mechanically ground and polished down to a thickness of 0.001 to 0.003 in. Final thinning was done electrolytically in a "chrome-acetic" electrolyte. When holes began to appear in the foil, the voltage was interrupted and applied in several 1-sec bursts. Sections of the foil between holes were thin enough to pass a 100-kv electron beam that carries an image.

Jan 1, 1965

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the seasor1 of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By Samuel Daniels

THE Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such con¬dition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400° to 600° F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400° F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600° F., the AI-Cu-Fe-Mg alloy at about 700° F. The former starts to reharden at 700° F., the latter at 800° F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500° and of 700° F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500° and 700° F. Although the latter can be made harder initially than the AI-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. CERTAIN aluminum alloys have been used for pistons and other parts operating at temperatures up to 650° F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance o corrosion. In the piston, the inertia forces and the bearing loading and with this the vibration are decreased. The piston head functions at a lower temperature (about 200° F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design.

Jan 2, 1926

By H. Le Chatelier

SILICA brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bred, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guérineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time we have intended to give an example of the manner in which scientific methods may be put to practical application in the solution of industrial problems. Although our work has been confined to samples of only a few grams, we are nevertheless convinced that our information can be directly utilized by brick-works of which the output is measured in thousands of tons

Jan 9, 1918

By J. B. Scuffham, G. Eggett, W. R. Hopkins

With solvent extraction now being accepted as a major method for recovering copper from leach liquors, the authors' company decided that in tankhouse design full advantage was not being taken of the benefits available from sol- vent extraction produced electrolytes. Consequently, a major development program was undertaken to examine means of operating such tankhouses with current densities in excess of current electrowinning practice. Techniques investigated included high circulation of liquors, current reversal and the application of ultrasonics. At the same time there was a necessity for improving the quality of cathodes produced from electrolytes of high free acid content. The application of anodes which are capable of reducing or eliminating the lead content of cathodes is described in the paper. The other problem area in eletrowinning from solvent extraction produced electrolytes is the production of a higher degree of acid mist. Techniques for alleviating this problem are described bearing in mind their possible effects on the solvent extraction section of the plant.

Jan 1, 1973

By William E. Ford, Edward Salisbury Dana

Examination in the Wet Way Examination by Means of the Blowpipe 479. The complete investigation of the chemical composition of a .mineral includes, first, the identification of the elements present by qualitative analysis, and, second, the determination of the relative amounts of each by quantitative analysis, from which last the formula can be calculated. Both processes carried out in full call for the equipment of a chemical laboratory. An approximate qualitative analysis, however, can, in many cases, be made quickly and simply with .few conveniences. The methods employed involve either (a) the use of acids or other reagents " in the wet way," or (b) the use

Jan 1, 1922

By T. F. Baily

DURING the period of the War, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the FIG. 1.-EXPERIMENTAL FURNACE. 5000 KW. CAPACITY: 150 TONS 2 PER CENT. SILICON PIG IRON PER DAY. electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted at Canton, Ohio, in

Jan 1, 1930

Discussion of the paper of DORSET A. LYON and ROBERT M. KEENEY, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin. No. 92, August, 1914, pp. 1791 to 1800. LAWRENCE ADDICKS, Chrome, N. J.-I read this paper for the first time this afternoon, and it is really worthy of a much more careful reply than I can make with such a short time to consider it, but I just want to say that I differ with Dr. Lyon in his premises and conception of what happens in a refining furnace. He cites steel as an instance where the production of special grades justifies the high cost of power in an electric furnace, and goes on to say the same will be true in the case of copper, for the reason that you will get a better quality of product. I don't think you will get a higher grade of copper,. or a better conductivity, as I will explain in a moment. The cost of fuel in the Eastern plants is somewhere between 30c. and 40c. per ton of copper refined, and, if my memory serves me correctly, in an open-hearth steel furnace it is something like $1.25, so it is evident that steel could be handled to better advantage than copper on the basis of fuel. Now, taking the Great Falls plant to compare with is not quite fair, because that plant operates under peculiar conditions. The furnaces are relatively small; the coal is very bad and is very high in sulphur. No one would think of using a coal with 3.6 per cent. sulphur were anything better available. Due to these conditions, the amount of slag is inordinate, it being quoted as 3.5 per cent., and it is necessary to use lime, as there is a tendency to have troubles from arsenic owing to the very high current density used. I think he has taken about as hard a case as he could pick out. Now as to the conductivity of copper, my own idea about the reason that melted copper does not give as high a conductivity as pieces drawn directly from a cathode, or native copper, is that in the latter case the impurities are present as a mechanical mixture, while after melting they are chemically combined with the copper, which is a very different condition. Further, it is necessary to take the sample from a relatively smooth and consequently pure part of the cathode, as otherwise it would not draw. The same with the mass of copper; you pick out a good solid part of the copper, which is not representative. In fact, the refiners have all found they could not take fair samples of cathodes for a chemical analysis. It is always customary to use wire-bar copper -for the purpose of sampling, and the impurities are several times as great as shown by samples taken from .the cathodes. I think if we examine all of the examples he has given of cases where copper is higher in conductivity, it will fit with that explanation. For example, the Elmore process is a direct electrolytic deposit. Incidentally, at the present time there are a number of ex-

Jan 12, 1914

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker's etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By S. S. Shen, M. J. Pool, P. J. Spencer, J. R. Guadagno

VERY few thermodynamic data are available for rare-earth alloys, partly because of the difficulties of obtaining the metals in sufficiently pure form and also because of their comparative scarcity up to the present time. The rare earths form a very interesting series in the periodic table in view of the progressive filling of their 4f subvalence electron shell and would be expected to provide useful information with regard to alloying characteristics of transition elements. It has been found in recent calorimetric investigations that the heats of solution of a number of the rare-earth metals in liquid tin are highly exothermic.1-4 Exceptionally strong bonding between rare-earth and tin atoms is clearly indicated in the liquid solutions. Continued thermodynamic studies of the behavior of rare earths in solution could thus contribute a great deal to present theoretical knowledge of alloying behavior and would yield an insight into bonding of a strength hitherto unencountered in liquid alloys. The determination of the heats of solution of the pure components in liquid tin is an essential preliminary to calorimetric work of this nature. Heats of solution of praseodymium, neodymium, and samarium in liquid tin at 750" ' and the heats of mixing of Pr-Nd solid solutions' have already been determined in this laboratory. The present investigations with lanthanum continue the study of rare-earth elements. Details of the construction and operation of the liquid metal solution calorimeter used in this work have been published previously by Pool and Peluso and no further description will be given here. The lanthanum used in heat of solution determinations was supplied by Lunex who quoted the purity as 99.9 pct. Their detailed analysis of the material is given in Table I. Samples of 0.0003 to 0.0005 g-atom were used for each run and great care was taken to remove all surface oxide prior to weighing. The samples were stored at all other times in a beaker of oil to prevent their otherwise rapid oxidation. The compounds LaSn (Cudu, L1P type structure) and La&, (structure not classified) were prepared from the appropriate quantities of the two pure components by arc melting under a purified argon atmosphere and once again great precautions were taken to avoid any subsequent oxidation of the specimens. Although no structural examination of the compounds was made, the consistency of thermodynarnic measurements carried out on twenty or so individual samples of each indicates that the compounds were in fact homogeneous, single phase alloys. Samples of the compounds consisting of 0.0003 to 0.002 moles were used in the calorimetric measurements. A solvent bath consisting of approximately 80 g of 99.9 pct pure Sn was used for each series of runs and its heat capacity was determined at regular intervals throughout the experiments using pure tin or tungsten calibration samples. Measurements were made of the heat of solution of lanthanum in liquid tin at 725", 750C, and 775°K and at compositions up to 2.21, 4.76, and 5.25 at. pct La at the three temperatures respectively. In every case, the heat of solution of lanthanum remained constant at its limiting value, within experimental limits, up to the highest lanthanum concentration investigated. Since no change in was observed, it was concluded that the liquid/liquid + LaSn, phase boundary had not been

Jan 1, 1969

By J. C. Scully

In June, 1965, Sanderson and scully5 reported at the Conference on Environment Sensitive Mechanical Properties of Materials at the Research Institute for Advanced Studies at Baltimore that thin foils of titanium could be prepared by chemical polishing in a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. The technique is simpler than that since reported by Rice and Orava. As-received annealed titanium (containing 0.8 pct Fe and 30 ppm H) in the form of sheet 0.05 cm thick is placed in the solution and moved up and down. The reaction is violent but suitable foils are obtained very easily and consistently. A typical micrograph is shown in Fig. 3. The small precipitates were not identified. Yamane and ueda6 observed many spotlike features which they referred to as small dislocation loops. While their spots may be due to the reaction of the warm foil with the air as suggested by Rice and Orava, the precipitates in Fig. 3 are also found when foils of titanium are prepared by electro-polishing at low temperatures and subsequently examined in the electron microscope without any inter- mediate warming. Furthermore, they are not a surface effect. It is necessary to add that alloys of titanium cannot be so easily thinned by the chemical polishing solution described above since it contaminates the a, phase with hydrogen and produces y hydride. These matters are described at length in a paper7 and their relevance to stress corrosion is considered elsewhere.'-* Author's Reply The authors are grateful to Dr. Scully for bringing to our attention his hitherto unpublished technique for thinning unalloyed titanium, and deeply regret the unintended apparent duplication. The chemical thinning solution (7 parts HNO3 and 3 parts HF, by volume) reported by us is the same as that with which, for some period in the past, we had experienced success in the preparation of foils from single and polycrystalline niobium. Its subsequent effective application to titanium was a logical step, which, clearly independently of Scully, was conceived by Mr. Rice, to whom full credit is due. A few comments are warranted concerning some of the details of the preceding Discussion. It is evident to the discerning reader that the two thinning techniques under consideration are chemically almost identical, and in that sense are equally "simple". The chemical aspect is, of course, the one of primary importance in both communications. Thereafter, the relative simplicity is dictated by the mechanics of the actual thinning operation selected by the individual investigator. Our standard dimpling, or dishing, procedure was chosen with a view toward providing, for the electron transparent areas of the sample, the maximum protection from extraneous deformation during handling. That the long, straight dislocations visible in Scully's electron micrograph of a seemingly recovered structure closely resemble handling dislocations would tend to indicate the merit of our adopted technique. Features similar to those which Scully has attributed to precipitates, without any apparent diffraction contrast confirmation, were not observed in any of our clean foils taken from annealed or deformed specimens. This was admittedly somewhat surprising since the 3700 ppm (nominal) Fe in the A-70 commercial-grade titanium examined should have given rise to TiFe precipitates. Presumably these existed but were un-resolvable. Curiously, Scully's "precipitate1' density is fairly high although the iron content quoted was less than one-fourth of that in our material. One is forced to conclude from the evidence that prior thermal and mechanical treatments are responsible for the two different types of structure observed.

Jan 1, 1968

By Harold Margalin, Elmars Ence

M. H. Mueller, M. V. Nevitt, and H. W. Knott (Argonne National Laboratory)—We have reported1 the crystal structure of Ti2CU as body centered tetragonal with a. = 2.944A and co = 10.786A, six atoms per unit cell, and space groupl4/mmm(MoSi2 type). This cell is larger but definitely related to the unit cell reported by the authors. It permits definite positions for the titanium and copper atoms in the cell located as follows: 2 Cu (a) 0 0 0; 1/2 1/2 1/2 4 Ti (e) 0 0 z; 1/2 1/2 1/2 + z; 0 0z; 1/2 1/2 1/2- z where z = 0.341 The face centered tetragonal cell reported by the authors can be transformed to a small body centered tetragonal cell with flo (small bet) = ao(fct)v2 Both unit cells have the same CO. Neither the face centered tetragonal cell with four atoms per unit cell nor the small body centered tetragonal cell with its two atoms per unit cell lend themselves conveniently to an orderly arrangment of the 2 to 1 ratio of titanium to copper atoms. When the co of this small body centered cell is tripled, however, a large body centered tetragonal cell results with six atoms per unit cell as described above. We had also noted that the X-ray patterns of Ti2Cu indicated that the structure could be approximately described by the face centered tetragonal cell as reported by the authors; how- ever, there was evidence for a few additional very weak lines whose positions indicated a larger unit cell. Since the X-ray scattering amplitudes of titanium and copper are nearly equal, it is evident that it is difficult to distinguish their positions especially from X-ray powder patterns. It was therefore decided to look at a powder pattern obtained by neutron diffraction since the scattering amplitudes of the two elements are considerably different in magnitude and opposite in sign. The sample used for neutron diffraction was selected from a group of three alloys prepared by arc melting using crystal bar titanium of 99.92 pet nominal purity and 99.999 pet pure Cu. The alloys designated as A, B, and C had the following respective compositions: Ti-32.8 at. pet Cu, Ti-33.3 at. pet Cu, and Ti-33.8 at. pet Cu. On the basis of the melting losses incurred, it was established that the actual concentration of either component in any of the alloys probably did not deviate from the intended value by as much as 0.1 at. pet. The alloys were annealed for 5 days at 700°C in evacuated Vycor capsules and quenched in tap water. The metallographic structures of these alloys are shown in Fig. 1. None of the alloys contained sufficient second phase to permit its positive identification. Since alloy B contained the least amount of second phase and since its composition placed it closest to the ideal stoichiometry, it was chosen for the neutron diffraction study. The oxygen content of alloy B was found by chemical analysis to be 0.06 at. pet. This particular intermetallic compound is especially suitable for investigation with neutron diffraction since if the titanium and copper atoms have a random statistical distribution, a near null-matrix would result in which there would be practically no coherent scattering of neutrons, and hence no Bragg diffraction peaks. Such a condition could come

Jan 1, 1962

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett's analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.'' Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett's analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.'' Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

By R. Shuttleworth, R. Smith

A Knudsen effusion tnethod I~as been used lo measure the vapor pressure of pure iron in the temperature range 1000° to 1500°C. Neutron-irradiated , natural iron was used and the Mn'~proclzdced by the (n, p) reaction removed by evaporation at high temperature. The results can be represented by the equation: where pM - 1.088 x 107 atm and T, = 20,890°K. A value of 100.2 kcal per g- atom was obtained for AH;. THE vapor pressure of pure iron in the temperature range 1000" to 1500°C has been measured. Radioactive iron and a Knudsen cell technique were used and the Mn' produced by an (n, p) reaction removed by evaporation at high temperature. From the variation of vapor pressure with temperature values of the enthalpy and entropy of solid iron have been found. Previous workers2 used a Lang-muir method and measurements were made over a smaller temperature range than that in this work. EXPERIMENTAL The apparatus used was similar to that of Pyle and Shuttleworth, and McLellan and Shuttle worth. However, because of the higher temperatures the Knudsen cell was machined from tungsten bar and the flanged furnace tube was beryllia. Heating was by passing a high current (70 amp at 7 v for 1500°K) through a strip of tantalum foil laid across the top of the cell and through a turn of molybdenum wire around the furnace tube. This method of heating ensured that the top of the cell was slightly hotter than the base and prevented condensation and re-evaporation from the orifice. The temperature was measured by means of a pt/Pt 13 pct Rh thermocouple spot-welded to the base of the crucible. To ensure accurate temperature measurement the iron was in the form of a thin disc (0.75 cm diam by 0.075 cm) which lay on the base of the cell. The high-purity iron was irradiated in the Harwell pile for a week at a neutron flux of 1.2 X 10" neutrons per sq cm per sec. The isotopes fe'~ and Fe" are produced by (n! y) reactions but only Fe", half-life 45.1 days, is a emitter; Mn which is also a y emitter, half-life 300 days, is produced simultaneously by an (n,p) reaction.' Immediately after irradiation of natural iron the ratio of ~e" to Mn y activity was 100:l. However, manganese is very much more volatile than iron and almost all the y activity of the condensate is due to Mn'~. Thus it was essential to eliminate all the manganeses before any measurement of the vapor pressure of iron was made and this was done by preliminary heating for 20 hr at 1400°C. For each determination the iron was dissolved from the target with acid and the y activity compared to a known weight of iron. By means of a y-ray spectrometer the y-activity measurements were made at the 1.09-mev peak of the 17e5' spectrum where the background was of the order of 3 cpm. Despite the low specific activity of ~e" a mass of 10- " g of iron could be determined corresponding to a vapor pressure of about l0-'' atm. RESULTS The vapor pressures were calculated from the equation: Where m is the mass of iron effusing in a time t through an orifice of area a2, r is the radius of the target, Z is the distance from the orifice to the

Jan 1, 1965

By E. P. Miesch, P. B. Crawford

A study was made of the effect of permeable and impermeable lenses in a reservoir on the production capacity of a well. Both steady-state and unsteady-state data were obtained. An electrical resistivity model was used to obtain the steady-state data and thermal models. were constructed to obtain the unsteady-state data. The productivity of a well is affected very greatly only when the lenses are close to the well. The effect of circular lenses on the productivity ratio can be correlated with the distance from the center of the lens to the center of the well divided by the radius of the lens. When this dimensionless distance is equal to six or greater, the effect of the lenses on production capacity will be negligible. The pseudo steady-state productivity of a heterogeneous reservoir can be predicted using steady-state data. INTRODUCTION Many analytical solutions of reservoir behavior assume that reservoir rock is uniform and homogeneous. Although this assumption is used, all of the data from core analyses and well logging indicate that the reservoirs are heterogeneous. Very little work has been done on the performance of heterogeneous reservoirs. The work of Landrum,l et al. showed that transient phenomena in oil reservoirs could be studied with thermal models. Pickering and Cotman2 used thermal models to study flow in stratified reservoirs and investigated the effect of inhomo-geneities in oil reservoirs on transient flow performance. Loucks3 made a mathematical study of the pressure build-up in a system composed of two concentric regions of different permeability. Root, Silberberg and Pirson4 studied the effect of the growth of the flooded region on water influx predictions using a thermal model consisting of three concentric cylindrical regions of different thermal properties which simulated the aquifer, the flooded region and the unflooded portion of the original hydrocarbon region. Tomme, et a1.5 made a mathematical study of vertical fractures. The object of this investigation was to study the effect of highly permeable and impermeable lenses in the vicinity of the wellbore on the pressure depletion history of the well. Steady-state data were obtained for both conductive and nonconductive lenses that completely penetrated the formation. The lenses were symmetrically located at various distances from the wellbore. The unsteady-state data were obtained on seven thermal models. EXPERIMENTAL EQUIPMENT AND PROCEDURE STEADY-STATE DATA The steady-state data were obtained from an electrical resistivity model 30 in. in diameter and approximately 11/2 in. deep. The outside of the model was lined with a 30-in. diameter copper strip, which served as the outer boundary of the reservoir. The bottom was covered with a sheet of plexiglass so that it would be nonconductive. The model was filled with a slightly saline solution. The well size was varied from an 0.064-in. diameter copper wire to a 10-in. diameter copper cylinder. Readings were taken with an impedance bridge using AC current to prevent polarization at the contacts. Copper and wax lenses were used to represent infinitely conductive and nonconductive lenses, respectively. The resistance was first measured for each well diameter with no lenses in the reservoir. Then the conductive and nonconductive lenses were spaced symmetrically at various distances from the well and the resistance read from each lens location. The diameters of the conductive lenses were 3, 1.022 and 0.624 in., and those of the nonconductive lenses were 3, 2.25 and 1.563 in. The ratio of each resistance reading to the resistance reading with no lenses in the reservoir

Jan 1, 1965

By Shun-ichi Satoh

Studies by many authorities have proved that nitrogen exerts an injurious influence upon iron and steel, but in the casehardening of steel by carbon, nitrogen has the advantage of accelerating the process of cementation. Its influence upon special steels is quite remarkable; it can produce the hardest layer ever known in metallurgical products—a fact hit upon by A. Fry and studied and ascertained by L. Guillet. As there have been very few investigations on the influence of nitrogen on special steels, the writer has listed important articles dealing with this problem and has conducted experiments on nitrification. He also has tested the influence of nickel upon the penetration of nitrogen in electric-arc welding. Nitrogen Process for Surface Hardening In 1919, Siegmonl conducted an experiment known as "Versticken" by treating steel with ammonia gas and found that the steel thus treated has the properties of resisting corrosion. In 1922, L. E. Benson3 nitro-genized iron and steel by sodium nitrate. Fry3-"studied the nitrogen process for surface hardening and published the results of his studies in 1923, 1924 and 1926. Guillet tested special steels containing various elements with the current of ammonia at 500' to 510' C.10, 11, 12, and determined the hardness of some of them at various temperatures.13 He also conducted corrosion tests14 in 1927. Fry15 stated that tinplat-ing could prevent nitrogen from penetrating into steel in the course of nitrification. In 1927, Guillet 65 described the historical notes of the nitrification; and many applications of nitrification were published in the Kruppsche Monatshefte.51, 59, 62, 63, 64-74~75 H. K. Herschman66 conducted the wear test of the nitrified steel. Gunnar Hägg investigated

Jan 1, 1930