Search Documents

By T. E. Evans, C. T. Baroch

ZrB2 was produced in batches of 4 to 6 Ib by interaction of ZrO2, B4C, B203, and carbon at around 2000°C in a simple graphite resistance furnace. Techniques of production are discussed and the final design of a suitable furnace is described in detail. Several other borides were made by the same technique and the process appears to have possibilities for commercial production. N seeking out new hard and refractory com- pounds, many researchers have turned to the investigation of the borides and excellent papers have been published on the properties of these compounds. Few papers, however, have appeared on the techniques and problems concerned with the production of these high temperature substances. This report describes progress made in developing a method for preparing zirconium diboride, ZrB2, on a pilot plant scale. The literature of the borides and other refractory hard metals recently has been reviewed, annotated, and classified so completely' that it is needless to attempt such an outline here. It is enough to say that three borides of zirconium have been reported: ZrB, ZrB2, and ZrB12.2 ZrB2 is the most stable of these and is especially stable in the presence of carbon up to and including its melting point of around 3000°C. Like most borides, it can be prepared in several ways. It can be prepared by synthesis of the elements, but these are expensive and difficult to produce in a high state of purity. Obviously, production directly from the oxides would have decided economic advantages. In electrolytic production such as that of calcium boride,:' the product is recovered as a sludge mixed with electrolyte; and separation of product from adhering electrolyte and regeneration of the electrolyte is an involved and difficult process. The work on borides was started on a small scale in 1948. Late in 1949, Naval Ordnance expressed a specific interest in ZrB2 and the project then centered on this compound. After the usual experimental work necessary in a new field, ZrB2 of good quality was produced by heating mixtures of B4C, ZrO2, B2O3, and carbon to a temperature of about 2000 °C in a resistance-type electric furnace. Over 100 lb was made for experimental use tests, and the method of production probably could be expanded into a commercial operation. A similar process has been described by Kieffer and coworkers.' The main chemical problems were the development of proper charges to insure complete reduction of the elements, determination of the proper temperature range at which these reductions took place, and adoption of techniques necessary to pre- vent inclusion of such impurities as carbon and nitrides. The mechanical problems consisted of developing a simple practical furnace that would attain the high temperatures required and permit use of a controlled atmosphere when necessary and determining of suitable refractories. Both problems were solved by designing a crucible resistance furnace. Crucible Resistance Electric Furnace Attempts were first made to produce ZrB2 in an electric arc furnace, but such a furnace would not provide the degree of carbon control required for producing clean graphite-free borides, so it was decided to try working in a crucible. Obviously, the furnace would have to be constructed of graphite, as the temperatures required are too high for other refractories or heating elements. Crucibles were made by hollowing out segments of graphite electrodes, which were fitted with a cover and clamped between two electrodes so that the current passing through the thin wall of the crucible would generate heat, using the principle of the Helberger crucible furnace."? Preliminary tests with this type of furnace were encouraging and led to the furnace design shown in Fig. 1. The essential components were a thin-walled graphite crucible resting on a graphite block, which formed the lower electrode assembly, and a top electrode assembly swung from a pipe column making contact with the top of the crucible. The space around the crucible was filled with graphite prepared from waste electrodes crushed to about ¼ in. This packing had excellent insulating properties, both electrically and thermally, and could be removed easily and quickly from around the crucible by means of an industrial vacuum cleaner. The largest resistor crucibles were machined from 8 in. electrode stock and were 26 in. long, with a side wall Yi in. thick and a 1 in. bottom. Temperatures were determined optically by sighting down a 1 in. hole drilled longitudinally through the top electrode and the crucible cover. Sealing this hole at the top was a water-cooled brass sight-glass assembly, shown in Fig. 2. An opening was provided for a light flow of helium to keep the sight opening clear of smoke, and a glass prism above the sight glass changed the line of sight to the horizontal for easier reading. More recently, the prism and optical pyrometer were replaced by a photoelectric recording pyrometer. At first the charges were placed directly in the resistor crucible but this meant that everything had to be withdrawn from the furnace every time the charge was emptied. Later, smaller crucibles were made up that could be placed inside the resistor

Jan 1, 1956

By Edgar C. Bain

A NUMBER probably a sizable group of person with a dominant interest in metals maintain contact with the developments in ferrous metallurgy by reading week by week, as time permits, some four or five periodical devoted in considerable part to this field. It seems possible that some of these, like ourself, find it difficult to see the net results of the development day by day in clear perspective, The impression sometimes seems blurred by the uninterrupted succession of so many accounts, or out of focus from the very impact of so many reports of new things enthusiastic, well written, and understandable though they usually are. It is at times almost as though one were trying to observe, from a fastmoving vehicle, objects all too near at hand. Or perhaps this impression is merely a manifestation of our individual hyperopia ; in which case we should content ourself with an observation that it would be more satisfactory on the whole to discuss in 1941 the metallurgical advances of 1930-35 than those of

Jan 1, 1941

By Everett D. Jackson

The largest deposits of chromite in the United States occur in tabular layers in the lower part of the Stillwater Complex, Montana. Nearly 900,000 long tons of chromite concentrates have been produced from mines and mills in this area, and reserves equivalent to more than 2,500,000 long tons of Cr2O3 remain in the ground. Layered concentrations of chromite (known as chromitite zones) occur only within olivine-rich layers of the Peridotite member of the Ultramafic zone of the Stillwater. As many as thirteen chromitite zones, lying conformably one above another, have been found, but only five of them are thick enough to be of any conceivable economic interest, and only two of them have been mined to date. Individual chromitite zones can be recognized by their distinctive internal character and by their stratigraphic position in the Peridotite member. The chemical composition of chromite varies consistently between and within the different chromitite zones. The zones range in thickness from about an inch to more than 12 feet, and the Cr2O3, content of their chromite ranges from 36.6 to 49.2 weight per cent. In any given area, the G chromitite zone is the thickest, but the chromite of the H chromitite zone has the highest grade. Laterally, the thickness of the chromitite zones is related to the thickness of the Peridotite member; in general all are thicker in the eastern part of the Stillwater than in the western part.

Jan 1, 1968

By C. Alstetter, V. Kerlins

By using alloys with subzero Ms temperatures, this investigation demonstrates that the amount of decomposition of martensite during the quench from austenite may be considerable and especially so in specimens of large cross -sections and high Ms temperatures. The activation energy for decomposition as measured dilutometrically is PREVTOUS investigations of the initial decomposition of Fe-C system martensite have invariably been limited to alloys having M, temperatures above a function of the amount of transformation which has taken place. The amount of transformation is a linear finction of log time. A correction term to the activation energy is derived for dilatometric measurements in which no end-point of the transformation is detected. room temperature. In such alloys the martensite is tempered during the quench to an extent dictated by the quench rate and temperature of formation. This tempering, called quench-tempering, Q-tempering, self-tempering, or auto-tempering, although frequently acknowledged, has not been studied or treated quantitatively. To do so one should obtain absolutely untempered martensite and study its decomposition. This as-formed martensite could be obtained either by extremely rapid quenching, requiring very thin specimens, or by lowering the martensite formation temperature range. The second alternative is more effective, because

Jan 1, 1963

By OTTO HERRES

TITANIUM is estimated to be the ninth most plentiful element, ranking after iron, aluminum, and magnesium, and ahead of copper, lead, and zinc. Vast quantities of titanium are widespread throughout the world in ore deposits and beach sands. Before the war, processing plants were operated in England, France, Italy, Czechoslovakia, Norway, Russia, Australia, United States, and Japan. In spite of its widespread occurrence, however, the U. S. Department of Justice has held the titanium industry to be a world monopoly and action was taken in the Federal court during the summer of 1945 to enjoin international patent and marketing agreements and to restore free competition. Possibly the rather surprising lack of public familiarity with this industry of international importance arises from its astonishingly rapid development and growth in the strong hands of some of the greatest chemical companies in the world, including the important foreign companies, Imperial Chemical Industries (British), Montecatini (Italian), I. G. Farben (German), and Titan Kogko Kabushiki Kaisha (Japanese). The rapid growth of the titanium industry in the United States is indicated by a tenfold increase of ore imports in the 1930 to 1940 decade before the war began to affect shipments from overseas. The fact that the industry formerly derived practically all ore for chemical processing in American plants from foreign sources probably also accounts for lack of general public knowledge of titanium. In 1939, to meet the requirements of increasing demand for the white pigment. titanium dioxide, more than 250,000 tons of titanium concentrates moved to this country, principally from the Travancore coast of India where the ilmenite concentrate from the beach sand runs as high as 60 per cent in titanium dioxide. Global warfare put a stop to shipping and thus gave rise to the development of titanium mining on a substantial scale in the United States during 1941.

Jan 1, 1946

By B. A. Wilcox, A. H. Clauer

The steady-state creep of TD Nickel NL + 2 001 pct TltOz) has been studied orer the telirperatve range 325&apos; to 1100O and the stress range 15,000 to 36,000 psi. At high temperatures (aboue 0.5 T& gran-boundary slzding is the )nost znportant )node of creep deformation, and the steady-state creep rate, is, can be related to stress and temperature by: where Q = 190 kcal pev mole and n has an unusually high value of 40. A creep mechanism based on cross slip of dislocations around The O2 particles can satisfactovily explain the low-temperature (T < 0.5 T,) cveep behavior, and the follo wing relation is applicable: Q, (a) is found to decrease from 57 to 46 kcal per mole as the stress is increased from 32,000 to 36,000 psi. THERE have been a variety of theories proposed to explain the influence of dispersed second-phase particles on the yield strength and flow stress of metals, and these have been reviewed recently by Kelly and icholson.&apos; However, only several attempts2"4 have been made to develop mechanistic treatments which characterize the creep behavior of dispersion-strengthened metals, and to date these have not been fully evaluated experimentally. weertman2 and Ansell and weertman3 proposed a quantitative creep theory for coarse-grairzed dispersion-strengthened metals, based on the concept that the rate-controlling process for steady-state creep was the climb of dislocations over second-phase particles, as suggested by choeck. The theory predicted that the steady-state creep rate, <,, was proportional to the applied stress, a, for low stresses and that is a4 o for high stresses. The activation energy for creep, Q,, was equivalent to that for self-diffusion, Qs.d., in the matrix. Some limited experimental evidence in support of this theory was obtained on a recrystallized Al-Alz03 S.A.P.-type alloy by Ansell and Lenel.6 Ansell and weertman3 also developed a semiquanti-tative theory for high-temperature creep of lineg-rained dispersion-strengthened metals in order to explain their results on an extruded S:A.P.-type alloy, which had a fine-grained fibrous structure. They suggested that the rate of dislocation generation from grain boundaries was the rate-controlling process, and fitted their results to the equation: where Q, was found to be 150 kcal per mole, i.e., QC- 4Q,.d. in aluminum. Similar high activation energies for creep7-&apos;&apos; and tensile deformation" of dispersion-strengthened alloys have been observed by other investigators for S.A.P.,&apos;" indium-glass bead omosites, and Ni + A1203 alls.&apos; There is no general agreement regarding the mechanisms involved in the creep of dispersion-strengthened metals, and this is due in part to the lack of detailed studies relating the structures of crept specimens to the mechanical behavior. The present investigation on thoriated nickel was undertaken with the aim of studying the structural changes which occur during creep of a dispersion-strengthened alloy and rationalizing the observed mechanical behavior in terms of the creep structures. EXPERIMENTAL METHODS The material used in this investigation was 1/2-in.-diam TD Nickel bar, which contained 2.3 vol pct Tho,. Obtained from E. I. duPont de Nemours & Co., Inc. The final fabrication treatment by DuPont consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fine-grained fibered structure with an average transverse grain size of -1 p and a longitudinal grain size of 10 to 15 p. Selected-area diffraction indicated that the fiber axis was parallel to (OOl), in agreement with the results of Inman eta1." All creep specimens were vacuum-annealed at 1300°C for 3 hr prior to testing. Transmission electron microscopy showed that the only structural change due to annealing was a slight decrease in dislocation density, confirming the reported high degree of structural stability.13 Furthermore, recrys-tallization or grain growth during creep was never observed. The structure typical of uncrept material (after the 1300 C, 3-hr anneal) is shown in Fig. 1. The grain boundaries are predominantly high angle and. although some areas show a tangled cell structure, the grain interiors are relatively dislocation-free. Individual dislocations are strongly pinned by the Tho2 particles; i.e., very rarely did dislocations move within a thin foil. The grey "halos" around some of the larger particles which protrude out of the foil surface arise from contamination in the electron microscoge. The Tho, particle size ranged from -100 to IOOOA, and the distribution is shown in Fig. 2. The technique used to obtain the data in Fig. 2 consisted of dissolving the nickel matrix in acid, collecting the Tho2 particles on cellulose acetate, and measuring about 1000 particle diameters in the electron microscope. Similar results were obtained by measuring about 600 particles in thin foils, an; the average particle size was found to be 2r, = 370A. Using the data in Fig. 2 (annealed structure), the mean planar center-to-center particle

Jan 1, 1967

By AIME AIME

APROXIMATELY one third of the world&apos;s iron ore is mined in the United States; and about 80 per cent of this third is mined in the Lake Superior ore region, and about 60 per cent in Minnesota. The Lake Superior iron ore region covers a vast area in the vicinity of Lake Superior that contained in early geological times large areas of iron-bearing sediments, which today form metamorphosed iron-bearing rocks, such as jasper, chert, taconite, and slates. Concentration of the iron content chiefly through solution and resultant removal of silica produced the ore bodies we find today in rock folds as on the Menominee range, at dike or impervious wall intersections such as on the Gogebic range, and blanket-type enriched ore bodies ly¬ing on or within the ore formation, such as occur on the Mesabi and in steeply pitching ore lenses elsewhere. In many places, folding and subsequent erosion of the tops of the folded areas has resulted in steep dips in the ore formation and contained ore bodies. The upper eroded edges are mostly buried under glacial over-burden. The slightly dipping Mesabi formation is the principal exception as to steeply dipping ore bodies.

Jan 1, 1941

By P. E. Busby, C. Wells

FURTHER study of data used in determinations of 1—rates of diffusion of boron in austenite and 2—solubilities of boron in the a and phases of iron and steel&apos; has provided an equation for the diffusion of boron in a iron. In brief, the previously published data were accumulated from the results of deboron-izing (and decarburizing) experiments carried out in the range of 700° to 1300°C. Diffusion coefficients (D?) for boron in austenite were calculated using the Grube solution of Fick&apos;s law. However, only solubility values were estimated from the discontinuous concentration-penetration curves, Fig. 1, which are characteristic of diffusion in two phases. Dr. Carl Wagner&apos; has recently provided a solution for calculating D values from penetration curves of this type as follows: Cl1.1 —C8/C8- C11.1 = vp ? e ? erf (?) and D = ?/4?2 t where C11,12, C8, C11, and E have the values shown in Fig. 1. D is the diffusion coefficient, sq cm per sec; t is time of deboronizing anneal, see; and ? is a di-mensionless parameter. For a given diffusion experiment, the value of ? can be readily obtained by graphical solution from a plot of y vs the right-hand part of Eq. 1. D may then be evaluated from Eq. 2. The avplication of this solution to previously re-ported results, of which excerpts are given in Table I, permits the calculation of diffusion coefficients for boron in a iron. On the basis of these meager data, it is tentatively concluded that the diffusion of boron in a may be represented by the equation Da = 1011 e-92,900/RT where R is the gas constant, cal X 0C-1 X mol-1; and T is the absolute temperature, OK. Although the frequency factor, 106 sq cm per sec, is admittedly several orders of magnitude higher than expected, the value of Q, 62,000 cal per mol, appears reasonable and is, in fact, very similar to that for the self-diffusion of iron. It is pertinent to mention at this point that the value of Q obtained for the diffusion of boron in austenite by means of the Wagner solution is 19,000 cal per mol and is in excellent agreement with the value previously reported1 in the equation DT = 2xl0-3 e-21,000/RT [4] which was determined by the application of the Grube solution to other data. The fact that determined constants A and Q in the equation D? = A e-Q/RT were practically the same, independent of whether the Wagner or Grube solutions were used in determinations of D values, strengthened the authors&apos; belief that the computed values of D (Table I) using the Wagner solution are reliable. The relative values in Eqs. 3 and 4 for the diffusion of boron in the a and ? phases, respectively, suggest that boron forms a substitutional solid solution in a iron and an interstitial solid solution in ? iron. The same tentative conclusion has been reached by McBride et al.3 on the basis of relative solubilities, atom diameter, and the size of the interstitial hole in a and ? iron. In connection with the data for test 14 listed in Table I, it is of interest to calculate the solubility of boron in a iron using the D value given by Eq. 3. As might be anticipated from the small movement of the interface in test 14, proper substitutions in Eqs. 2 and 1 give a low value, approximately 0.0004 pct B, at 850°C. Apparently at 835°C (test 13) it is possible to obtain 0.0018 pct B, and at 850°C only 0.0004 pct B into solution in the a phase before a second phase appears. These observations are consistent with the Fe-B constitution diagram proposed by McBride, Spretnak, and Speiser.3 References P. E. Busby, M. E. Warga, and C. Wells: Diffusion and Solubility of Boron in Iron and Steel. Trans. AIME (1953) 197, p. 1463; Journal of Metals (November 1953). &apos;W. Jost: Diffusion in Solids, Liquids, Gases. (1952) pp. 69-71. New York. Academic Press Inc. "C. C. McBride, J. W. Spretnak, and R. Speiser: A Study of the Fe-Fe2B System. Trans. ASM (1954) 46, p. 499.

Jan 1, 1955

By Paul Weir

PRODUCTION METHODS in the bituminous coal mines in the United States are undergoing many changes. Although the primary object of these changes is the production of a better product at a cheaper cost there are other considerations such as the improvement of conditions under which miners live and work. The almost complete unionization of the manual workers in the industry during the past four years has &apos;brought with it a stabilization of wages on a relatively high basis and of hours of work per day and per week on a relatively low basis. With differentials in wages between producing districts firmly established, and with a nation- wide and uniform application of in-

Jan 1, 1937

By John E. Murphy, Ernest L. Ohle

Hematite-magnetite ore bodies at Iron Mountain, Missouri, have produced nearly 9 million tons of iron ore concentrates since 1844. The ore minerals occur principally as open-space filling in fractured and brecciated andesite porphyry with very minor replacement of the wall rocks. The enclosing rocks are Precambrian in age and consist of a series of dacite, rhyolite, and andesite flows aggregating about 2000 feet in thickness. All of the ore is in andesite and the mineralization is Precambrian in age. The shape of the ore bodies, the breccia character of the ore, and the gangue mineralogy are believed to be unique. One of the two main ore bodies is crudely dome-shaped with a tendency for development of concentric mineralized shells; the other is an elongated lense in plan but hook-shaped in cross section. Both have strong linear elements striking northeast, east-west, or northwest. Various modes of origin for the structures and for the tension breccias have been suggested, but none is completely satisfactory. Hematite is the main ore mineral; magnetite is subordinate. Important gangue minerals are andradite, quartz, calcite, actinolite, apatite, epidote, and chlorite. Although some evidence favors injection of an iron-rich melt, other evidence suggests ore formation by a high temperature, water-rich solution.

Jan 1, 1968

By Granville S. Borden

TAXES in general are onerous and are not a pleas- ant subject for discourse. There are, however, some very cogent reasons why we should dedicate a part of our thoughts and services to the solution of our taxation problems: The happiness of every individual in the United States depends on the maintenance of a stable government. The collection of taxes is an indispensable function of a stable government, and the power to collect taxes depends in part on the question whether taxes are fair and equitable. As representatives of the mining industry it is our duty to .protect it from tax burdens that are discriminatory or- unjust, As citizens we find that taxation is incessantly endeavouring to unravel the knots in our purse-strings. Many members of the Institute may be consulted .by clients on taxation problems, especially the phases which re- late to depletion and valuation. It is the hope of the writer that the discussion of some of the current depletion and valuation problems will stimulate interest in the problems, and as a consequence of this new interest facts will be ventilated, opinions rendered and services performed, which will be a means of solving the problems to the satisfaction of all parties interested.

Jan 1, 1929

By WILLIAM COUPER

THE completion of the excavation of the tunnels through Bergen Hill for the extension of the Pennsylvania Railroad into New York City, together with the fact that the excavation for the rest of the tunnel-line has been practically completed for some time past, arouses sufficient interest to justify a description of the engineering- and contracting-work, and the organization by which it has been accomplished. The finishing of the excavation is a long step towards the completion of the entire tunnel-project. It will be interesting to the members of the Institute, who last spring were taken through a great part of this work, to know that by the excavation now completed it is possible to walk by tunnel from a, point near Sunnyside yard, Long Island, east of the 34th Street ferry, to the central passenger station site in the City of New York, and thence by tunnel to the Hackensack meadows, and by an embankment constructed across these meadows to Newark, N. J. This New York tunnel extension is being constructed as a part of the Pennsylvania Railroad system by the Pennsylvania Tunnel & Terminal R. R. Co., a corporation of the States of New Jersey and New York. It extends from a point near Newark, N. J., to the Sunnyside yard, Long Island, as indicated on the accompanying plan.

Jan 7, 1908

By Woolf, W. G.

Filtration of hot (60°C) supersaturated zinc sulphate solution (sp gr 1.540) from slimy leach residues at the electrolytic zinc plant of Sullivan Mining Co., Kellogg, Idaho, is de- scribed. Separation of liquids and solids in the finished leach is by Burt filters modified to meet conditions of high-acid, high-density process for electrolytic zinc. Operating characteristics of the Burt filter on this pulp are presented.

Jan 1, 1950

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By J. F. Tavernelli, L. F. Coffin

The deformation and fracture characteristics of eight metals subjected to fully reversed cyclic strain ranging from 0.2 to 50 pct were investigated at room temperature. Strain-hardening characteristics unique to the interna1 structure of a particular metal were found. Complete removal of the strain-hardening effects resulting from prior deformation was brought about by subsequent cyclic strain. Further support for the validity of the inverse relationship between the plastic strain range and the square root of the number of cycles for failure is given. THE resistance of materials to cyclic plastic strain is of interest both from a fundamental and practical point of view. It is now a well-accepted fact that fatigue failure in metals is a consequence of the localized slip deformation which occurs within the individual crystals of metal.&apos;-&apos; Hence the failure process should be strongly dependent upon the magnitude of the gross cyclic plastic deformation of the metal under conditions where this is a measurable quantity. Therefore, an experimental investigation of metals in which the cyclic plastic strain is the independent variable should shed new light on some of the basic aspects of the problem. From the practical point of view, there are many uses for information relating to the cyclic strain resistance of metals. One is the case of thermal stress fatigue where fatigue failure can occur as a consequence of a com- paratively few cycles of thermally induced mechanical deformation. Another is the mechanical working of metals where large cyclic strains are employed. In recent years several publications have appeared relating to the cyclic-strain resistance of metals,8-11 dealing mostly with the fracture aspects where the temperature is cycled simultaneously with the mechanical strain. Some work has been reported on the cyclic-strain resistance of metals at constant temperature, again oriented more toward the fracture aspects of the problem than the deformation aspects. 12-16 The present research investigation was undertaken to obtain information regarding the deformation characteristics of several metals whose structure-property relationships were simple and straightforward under conditions of both cyclic and monotonic strain. It has been shown for example that under cyclic-strain conditions some materials will strain harden, while other materials, particularly cold-worked structures, strain soften and these effects required further clarification.8,17-19 It was also de-

Jan 1, 1960

By R. D. Carnahan

The authors are to be complimented on their timely study of solution-hardening effects in a bcc metal. Unfortunately there are some misleading aspects of the paper that should be discussed and clarified which is the purpose of this letter. In particular the writer is concerned about the allusions to rate theory of deformation that are inferred by the authors. This position is taken on the basis first of the "weaker" temperature dependence of the yield and flow stresses of the alloy relative to pure niobium and second of the strong temperature dependence of the Young&apos;s modulus of elasticity. It is by now well-recognized that any collection of data points used to determine a flow-stress temperature-dependence relationship must be established under isostructural conditions, i.e., similar or identical sessile and mobile dislocation densities and arrangements. Admittedly this is a formidable experimental undertaking and not what would be expected in an exploratory investigation of the present kind. As an alternative to the former one can consider, however, the temperature dependence of flow stresses at comparable strains. In the present study the authors have elected to use the lower yield stress and ultimate strengths to exhibit the temperature dependence of their alloys except for the data points taken at liquid nitrogen temperature. Here they have used the proportional limit for the yield stress and the fracture stress for the ultimate strength. This seems to be an unrealistic choice particularly in view of the fact that this temperature is below the duc tile-brittle transition region for the alloy and no supporting data points were obtained between -55" and -196°C. If the authors&apos; data in Fig. 2 are extrapolated and data points selected at a constant strain, for example a strain of 0.01, the reader can quickly verify that a temperature dependence exactly paralleling that of pure niobium is obtained.

Jan 1, 1967

By I. H. Warren, E. Devuyst

A review of the physical and chemical aspects of the direct leaching of metal oxides has been given and com- pared to recent data of the authors and co-workers. The physical aspects, including the anisotropy of the dissolution, the hydration and the zero point of charge of some metal oxides are discussed first and then the kinetics of the dissolution of metal oxides are considered. A general mechanism of the leaching of oxides which describes most of the observed results is proposed.

Jan 1, 1973

By William H. Waggaman

CURTAILMENT of the mineral industry as a whole undoubtedly will follow world peace, but the output of certain minerals should pursue a course well above the average on any curve of probable output projected beyond the trends exhibited through 1939. Without speculating on industrial conditions in the pending recomversion period, demand for fluorspar should be greater than before the war because of these factors, introduced by or resulting directly from military necessity: (1) Discovery and development of new deposits. (2) Improved technology in benefication. (3) New and expanded uses for fluorspar and its derivatives. The steel industry has been and continues to be the greatest consumer of fluorspar, and it wag largely to meet the wartime needs for steel that the domestic fluorspar industry has been expanded so greatly. Not only were the search for and development of new deposits of this mineral considered esstinal but the marginal nature of some of the,c- domestic deposits made it necessary to improve mineral dressinc and processing techniques to utilize them

Jan 1, 1945

By Henry Newton

It may seem somewhat a work of supererogation to present to the American Institute of Mining Engineers, composed largely of gentlemen with whom the subject is so familiar, a paper on iron ores and their distribution. To many of them, however, it possibly will not be without interest, as there may be some, like myself, who hare nowhere found a connected account of the character of the deposits and the circumstances upon which are founded the great iron-producing centres of the world. This blank I have endeavored to fill,

By Henry Newton

IT may seem somewhat a work of supererogation to present to the American Institute of Mining Engineers, composed largely of gentle- men with whom the subject is so familiar, a paper on iron ores and their distribution. To many of them, however, it possibly will not be without interest, as there may be some, like myself, who hare nowhere found a connected account of the character of the deposits and the circumstances upon which are founded the great iron-producing centres of the world. This blank I have endeavored to fill,

Jan 1, 1875